74HC1G86GW.125 NXP

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 11

Technical content

2-input EXCLUSIVE-OR function. The HC device has CMOS input switching levels and supply voltage range 2 V to 6 V. The HCT device has TTL input switching levels and supply voltage range 4.5 V to 5.5 V. The standard output currents are half those of the 74HC/HCT86. Table 1. Ordering information Table 2. Marking codes

74HC_HCT1G86_4 © NXP B.V. 2007. All rights reserved.

6.1 Pinning

6.2 Pin description

Table 3. Pin description

74HC_HCT1G86_4 © NXP B.V. 2007. All rights reserved. [1] The input and output voltage ratings may be exceeded if the input and output current ratings are observed. [2] Above 55°C the value of Ptot derates linearly with 2.5 mW/K.

  1. Recommended operating conditions

Table 4. Function table Table 5. Limiting values Table 6. Recommended operating conditions Voltages are referenced to GND (ground = 0 V).

74HC_HCT1G86_4 © NXP B.V. 2007. All rights reserved. Table 7. Static characteristics Voltages are referenced to GND (ground = 0 V). All typical values are measured at Tamb =2 5°C.

74HC_HCT1G86_4 © NXP B.V. 2007. All rights reserved. [1] tpd is the same as tPLH and tPHL . [2] C PD is used to determine the dynamic power dissipation PD (µW). Table 7. Static characteristics …continued Voltages are referenced to GND (ground = 0 V). All typical values are measured at Tamb =2 5°C. Table 8. Dynamic characteristics

74HC_HCT1G86_4 © NXP B.V. 2007. All rights reserved. Product data sheet Rev. 04 — 20 July 2007 6 of 11 NXP Semiconductors 74HC1G86; 74HCT1G86 2-input EXCLUSIVE-OR gate 12. Waveforms For 74HC1G86: VM = 0.5× VCC ; VI= GND to VCC . For 74HCT1G86: VM = 1.3 V; VI= GND to 3.0 V. Fig 5. The input (A and B) to output (Y) propagation delays mna041 tPHL tPLH VM VMA, B input Y output Test data is given inTable8. Definitions for test circuit: C L = Load capacitance including jig and probe capacitance. R T = Termination resistance should be equal to output impedance Zo of the pulse generator. Fig 6. Load circuitry for switching times VCC VI VO mna034 DUT C L 50 pFR T PULSE GENERATOR

74HC_HCT1G86_4 © NXP B.V. 2007. All rights reserved. Product data sheet Rev. 04 — 20 July 2007 7 of 11 NXP Semiconductors 74HC1G86; 74HCT1G86 2-input EXCLUSIVE-OR gate 13. Package outline Fig 7. Package outline SOT353-1 (TSSOP5) UNIT A 1 A max. A 2 A 3 bp LH E Lp wyvce D (1) E(1) Z(1) q REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA mm 0.1 1.0 0.8 0.30 0.15 0.25 0.08 2.25 1.85 1.35 1.15 0.65 1.3 2.25 2.0 0.60 0.15 0°0.1 0.10.30.425 DIMENSIONS (mm are the original dimensions) Note 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 0.46 0.21 SOT353-1 MO-203 SC-88A 00-09-01 03-02-19 w Mbp D Z e 0.15 5 4 q AA2 Lp (A3) detail X L H E E c v M A X A y 1.5 3 mm0 scale TSSOP5: plastic thin shrink small outline package; 5 leads; body width 1.25 mm SOT353-1 1.1

74HC_HCT1G86_4 © NXP B.V. 2007. All rights reserved. Product data sheet Rev. 04 — 20 July 2007 8 of 11 NXP Semiconductors 74HC1G86; 74HCT1G86 2-input EXCLUSIVE-OR gate Fig 8. Package outline SOT753 (SC-74A) REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA SOT753 SC-74A wB Mbp D e A Lp Q detail X H E E v M A AB y 0 1 2 mm scale c X 13 2 Plastic surface-mounted package; 5 leads SOT753 UNIT A 1 bp cD E H E Lp Qy wv mm 0.100 0.013 0.40 0.25 3.1 2.7 0.26 0.10 1.7 1.3 e 0.95 3.0 2.5 0.2 0.10.2 DIMENSIONS (mm are the original dimensions) 0.6 0.2 0.33 0.23 A 1.1 0.9 02-04-16 06-03-16

74HC_HCT1G86_4 © NXP B.V. 2007. All rights reserved. Table 9. Abbreviations Table 10. Revision history

  • The format of this data sheet has been redesigned to comply with the new identity guidelines of NXP Semiconductors.
  • Legal texts have been adapted to the new company name where appropriate.
  • Package SOT353 changed to SOT353-1 inTable1 andFigure7.
  • Quick Reference Data and Soldering sections removed.
  • Section 2 “Features” updated. 74HC_HCT1G86_3 20020515 Product specification - 74HC_HCT1G86_2 74HC_HCT1G86_2 20010406 Product specification - 74HC_HCT1G86_1 74HC_HCT1G86_1 19980805 Product specification - -

74HC_HCT1G86_4 © NXP B.V. 2007. All rights reserved. Product data sheet Rev. 04 — 20 July 2007 10 of 11 NXP Semiconductors 74HC1G86; 74HCT1G86 2-input EXCLUSIVE-OR gate 16. Legal information

16.1 Data sheet status

[1] Please consult the most recently issued document before initiating or completing a design. [2] The term ‘short data sheet’ is explained in section “Definitions”. [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com.

16.2 Definitions

Draft —The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet —A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail.

16.3 Disclaimers

General — Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. Right to make changes —NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use —NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in medical, military, aircraft, space or life support equipment, nor in applications where failure or malfunction of a NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors accepts no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk. Applications —Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Limiting values —Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) may cause permanent damage to the device. Limiting values are stress ratings only and operation of the device at these or any other conditions above those given in the Characteristics sections of this document is not implied. Exposure to limiting values for extended periods may affect device reliability. Terms and conditions of sale —NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms , including those pertaining to warranty, intellectual property rights infringement and limitation of liability, unless explicitly otherwise agreed to in writing by NXP Semiconductors. In case of any inconsistency or conflict between information in this document and such terms and conditions, the latter will prevail. No offer to sell or license —Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights.

16.4 Trademarks

Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. 17. Contact information For additional information, please visit:http://www.nxp.com For sales office addresses, send an email to:salesaddresses@nxp.com Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification.

NXP Semiconductors 74HC1G86; 74HCT1G86 2-input EXCLUSIVE-OR gate © NXP B.V. 2007. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com Date of release: 20 July 2007 Document identifier: 74HC_HCT1G86_4 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section ‘Legal information’. 18. Contents