DATASHEET SEARCH SITE
Document overview
- Manufacturer or author: Provided By digicamel.com
- PDF pages: 30
Technical content
- General description The 74HC193; 74HCT193 is a 4-bit synchronous binary up/down counter. Separate up/down clocks, CPU and CPD respectively, simplify operation. The outputs change state synchronously with the LOW-to-HIGH transition of either clock input. If the CPU clock is pulsed while CPD is held HIGH, the device will count up. If the CPD clock is pulsed while CPU is held HIGH, the device will count down. Only one clock input can be held HIGH at any time to guarantee predictable behaviour. The device can be cleared at any time by the asynchronous master reset input (MR); it may also be loaded in parallel by activating the asynchronous parallel load input (PL). The terminal count up (TCU) and terminal count down (TCD) outputs are normally HIGH. When the circuit has reached the maximum count state of 15, the next HIGH-to-LOW transition of CPU will cause TCU to go LOW. TCU will stay LOW until CPU goes HIGH again, duplicating the count up clock. Likewise, the TCD output will go LOW when the circuit is in the zero state and the CPD goes LOW. The terminal count outputs can be used as the clock input signals to the next higher order circuit in a multistage counter, since they duplicate the clock waveforms. Multistage counters will not be fully synchronous, since there is a slight delay time difference added for each stage that is added. The counter may be preset by the asynchronous parallel load capability of the circuit. Information present on the parallel data inputs (D0 to D3) is loaded into the counter and appears on the outputs (Q0 to Q3) regardless of the conditions of the clock inputs when the parallel load (PL ) input is LOW. A HIGH level on the master reset (MR) input will disable the parallel load gates, override both clock inputs and set all outputs (Q0 to Q3) LOW. If one of the clock inputs is LOW during and after a reset or load operation, the next LOW-to-HIGH transition of that clock will be interpreted as a legitimate signal and will be counted. Inputs include clamp diodes. This enables the use of current limiting resistors to interface inputs to voltages in excess of V CC. 2. Features and benefits Input levels: For 74HC193: CMOS level For 74HCT193: TTL level Synchronous reversible 4-bit binary counting Asynchronous parallel load Asynchronous reset Expandable without external logic Complies with JEDEC standard no. 7A ESD protection: HBM JESD22-A114F exceeds 2000 V MM JESD22-A115-A exceeds 200 V. 74HC193; 74HCT193 Presettable synchronous 4-bit binary up/down counter Rev. 4 — 24 June 2013 Product data sheet
Table 1. Ordering information
Product data sheet Rev. 4 — 24 June 2013 3 of 30 NXP Semiconductors 74HC193; 74HCT193 Presettable synchronous 4-bit binary up/down counter Fig 3. IEC logic symbol CTR4 2CT = 0 1CT = 15 001aag410 4 G1 11 C3 14 R
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx Product data sheet Rev. 4 — 24 June 2013 4 of 30 NXP Semiconductors 74HC193; 74HCT193 Presettable synchronous 4-bit binary up/down counter Fig 4. Logic diagram 001aag412 D0 D1 D2 D3 Q0 Q1 Q2 Q3 TCD PL CPU CPD MR SD FF1 RD Q Q T SD FF2 RD Q Q T SD FF3 RD Q Q T SD FF4 RD Q Q T TCU
5.1 Pinning
5.2 Pin description
[1] LOW-to-HIGH, edge triggered. Table 2. Pin description
= LOW-to-HIGH clock transition. [3] TC D = CPD at terminal count down (LLLL). Table 3. Function table [1]
Product data sheet Rev. 4 — 24 June 2013 7 of 30 NXP Semiconductors 74HC193; 74HCT193 Presettable synchronous 4-bit binary up/down counter (1) Clear overrides load, data and count inputs. (2) When counting up, the count down clock input (CPD) must be HIGH, when counting down the count up clock input (CPU) must be HIGH. Sequence Clear (reset outputs to zero); load (preset) to binary thirteen; count up to fourteen, fifteen, terminal count up, zero, one and two; count down to one, zero, terminal count down, fifteen, fourteen and thirteen. Fig 8. Typical clear, load and count sequence 001aag411 COUNT UP COUNT DOWN 01 3 CLEAR PRESET 1 0 15 14 1314 15 0 1 2 MR(1) PL CPU (2) CPD(2) TCU TCD
[1] The input and output voltage ratings may be exceeded if the input and output current ratings are observed. [2] For DIP16 packages: above 70 C the value of Ptot derates linearly at 12 mW/K. For SO16 packages: above 70 C the value of Ptot derates linearly at 8 mW/K. For SSOP16 and TSSOP16 packages: above 60 C the value of Ptot derates linearly at 5.5 mW/K.
- Recommended operating conditions
Table 4. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V). Table 5. Recommended operating conditions
Table 6. Static characteristics type 74HC193 At recommended operating conditions; voltages are referenced to GND (ground = 0 V).
Table 6. Static characteristics type 74HC193 …continued At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Table 7. Static characteristics type 74HCT193 At recommended operating conditions; voltages are referenced to GND (ground = 0 V).
Table 7. Static characteristics type 74HCT193 …continued At recommended operating conditions; voltages are referenced to GND (ground = 0 V).
At recommended operating conditions; voltages are referenced to GND (ground = 0 V).
[1] t pd is the same as tPHL and tPLH. (CL VCC2 fo) = sum of outputs.
1.5 V; VCC =5V ;
Table 9. Dynamic characteristics type 74HCT193 …continued
Product data sheet Rev. 4 — 24 June 2013 18 of 30 NXP Semiconductors 74HC193; 74HCT193 Presettable synchronous 4-bit binary up/down counter 11. Waveforms Measurement points are given in Table 10. tPLH and tPHL are the same as tpd. Logic levels VOL and VOH are typical output voltage levels that occur with the output load. Fig 9. The clock (CPU, CPD) to output (Qn) propagation delays, the clock pulse width, and the maximum clock pulse frequency 001aag413 CPU, CPD input VI GND VOH VOL Qn output tPHL tPLH tW VM VM 1/fmax Measurement points are given in Table 10. tPLH and tPHL are the same as tpd. Logic levels VOL and VOH are typical output voltage levels that occur with the output load. Fig 10. The clock (CPU, CPD) to terminal count output (TCU,T C D) propagation delays 001aag414 CPU, CPD input TCU, TCD output tPHL VI GND VOH VOL tPLH VM VM
Product data sheet Rev. 4 — 24 June 2013 19 of 30 NXP Semiconductors 74HC193; 74HCT193 Presettable synchronous 4-bit binary up/down counter Measurement points are given in Table 10. tPLH and tPHL are the same as tpd. Logic levels VOL and VOH are typical output voltage levels that occur with the output load. Fig 11. The parallel load input (PL ) and data (Dn) to Qn output propagation delays and PL removal time to clock input (CPU, CPD) 001aag415 Dn input VI GND VI GND VI GND VOH VOL Qn output CPU, CPD input PL input V M VM VM VM tW trec tPLH tPHL Measurement points are given in Table 10. tPLH and tPHL are the same as tpd. Logic levels VOL and VOH are typical output voltage levels that occur with the output load. Fig 12. The master reset input (MR) pulse width, MR to Qn propagation delays, MR to CPU, CPD removal time and output transition times 001aag416 MR input Qn output VOH VOL VI GND VI GND CPU, CPD input VM VM VM 10 % 90 % trec tPHL tTHL tW tTLH
Product data sheet Rev. 4 — 24 June 2013 20 of 30 NXP Semiconductors 74HC193; 74HCT193 Presettable synchronous 4-bit binary up/down counter The shaded areas indicate when the input is permitted to change for predictable output performance. Measurement points are given in Table 10. Logic levels VOL and VOH are typical output voltage levels that occur with the output load. Fig 13. The data input (Dn) to parallel load input (PL ) set-up and hold times 001aag417 Dn input Qn output VOL VOH GND VI GND VI PL input VM tsu th VM tsu th Measurement points are given in Table 10. tPLH and tPHL are the same as tpd. Logic levels VOL and VOH are typical output voltage levels that occur with the output load. Fig 14. The data input (Dn), parallel load input (PL ) and the master reset input (MR) to the terminal count outputs (TCU,T C D) propagation delays 001aag418 PL, MR, Dn input TCU, TCD output t PLH tPHL VM VM VOL VOH GND VI Measurement points are given in Table 10. Fig 15. The CPU to CPD or CPD to CPU hold times 001aag419 CPD or CPU input CPU or CPD input VI GND VI GND VM VM th
Table 10. Measurement points Test data is given in Table 11. Table 11. Test data
Product data sheet Rev. 4 — 24 June 2013 22 of 30 NXP Semiconductors 74HC193; 74HCT193 Presettable synchronous 4-bit binary up/down counter 12. Application information Fig 17. Application for cascaded up/down counter with parallel load 001aag420 data input IC1 IC2 data output up clock down clock carry borrow asynchronous parallel load reset D0 D1 D2 D3 Q0 Q1 Q2 Q3 TCU TCD MR CPU CPD PL D0 D1 D2 D3 Q0 Q1 Q2 Q3 TCU TCD MR CPU CPD PL
Product data sheet Rev. 4 — 24 June 2013 23 of 30 NXP Semiconductors 74HC193; 74HCT193 Presettable synchronous 4-bit binary up/down counter 13. Package outline Fig 18. Package outline SOT109-1 (SO16) X w M θ AA1 bp D HE Lp Q detail X E Z e c L v M A (A )3 A y pin 1 index UNIT A max. A1 A2 A3 bp cD (1) E(1) (1)eH E LL p QZ y w v θ REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA mm inches 1.75 0.25 0.10 1.45 1.25 0.25 0.49 0.36 0.25 0.19 10.0 9.8 4.0 3.8 1.27 6.2 5.8 0.7 0.6 0.7 0.3 8 o o 0.25 0.1 DIMENSIONS (inch dimensions are derived from the original mm dimensions) Note 1. Plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included. 1.0 0.4 SOT109-1 99-12-27 03-02-19 076E07 MS-012 0.069 0.010 0.004 0.057 0.049 0.01 0.019 0.014 0.0100 0.0075 0.39 0.38 0.16 0.15 0.05 1.05 0.0410.244 0.228 0.028 0.020 0.028 0.0120.01 0.25 0.01 0.0040.039 0.016 0 2.5 5 mm scale SO16: plastic small outline package; 16 leads; body width 3.9 mm SOT109-1
Product data sheet Rev. 4 — 24 June 2013 24 of 30 NXP Semiconductors 74HC193; 74HCT193 Presettable synchronous 4-bit binary up/down counter Fig 19. Package outline SOT338-1 (SSOP16) UNIT A1 A2 A3 bp cD (1) E (1) eH E LL p QZ y w v θ REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA mm 0.21 0.05 1.80 1.65 0.25 0.38 0.25 0.20 0.09 6.4 6.0 5.4 5.2 0.65 1.257.9 7.6 1.03 0.63 0.9 0.7 1.00 0.55 o o0.130.2 0.1 DIMENSIONS (mm are the original dimensions) Note 1. Plastic or metal protrusions of 0.25 mm maximum per side are not included. SOT338-1 99-12-27 03-02-19 (1) w M bp D HE E Z e c v M A X A y 1 8 16 9 θ AA1 Lp Q detail X L (A )3 MO-150 pin 1 index 0 2.5 5 mm scale SSOP16: plastic shrink small outline package; 16 leads; body width 5.3 mm SOT338-1 A max.
Product data sheet Rev. 4 — 24 June 2013 25 of 30 NXP Semiconductors 74HC193; 74HCT193 Presettable synchronous 4-bit binary up/down counter Fig 20. Package outline SOT38-4 (DIP16) REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA SOT38-4 95-01-14 03-02-13 MH c (e )1 ME A L seating plane w M e D Z E pin 1 index b 0 5 10 mm scale Note 1. Plastic or metal protrusions of 0.25 mm (0.01 inch) maximum per side are not included. UNIT A max. 12 b1 (1) (1) (1) b2 cD E e M ZHL mm DIMENSIONS (inch dimensions are derived from the original mm dimensions) A min. A max. b max.wMEe1 1.73 1.30 0.53 0.38 0.36 0.23 19.50 18.55 6.48 6.20 3.60 7.80 10.0 inches 0.068 0.051 0.021 0.015 0.014 0.009 1.25 0.85 0.049 0.033 0.77 0.73 0.26 0.24 0.14 0.31 0.39 DIP16: plastic dual in-line package; 16 leads (300 mil) SOT38-4
Product data sheet Rev. 4 — 24 June 2013 26 of 30 NXP Semiconductors 74HC193; 74HCT193 Presettable synchronous 4-bit binary up/down counter Fig 21. Package outline SOT403-1 (TSSOP16) UNIT A1 A2 A3 bp cD (1) E (2) (1)eH E LL p QZ y w v θ REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA mm 0.15 0.05 0.95 0.80 0.30 0.19 0.2 0.1 5.1 4.9 4.5 4.3 0.65 6.6 6.2 0.4 0.3 0.40 0.06 o o0.13 0.10.21 DIMENSIONS (mm are the original dimensions) Notes 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. Plastic interlead protrusions of 0.25 mm maximum per side are not included. 0.75 0.50 SOT403-1 MO-153 99-12-27 03-02-18 w M bp D Z e 0.25 16 9 θ AA1 Lp Q detail X L (A )3 HE E c v M A XA y 0 2.5 5 mm scale TSSOP16: plastic thin shrink small outline package; 16 leads; body width 4.4 mm SOT403-1 A max. 1.1 pin 1 index
Table 12. Abbreviations Table 13. Revision history
- General description updated. 74HC_HCT193 v.3 20070523 Product data sheet - 74HC_HCT193_CNV v.2 Modifications:
- The format of this data sheet has been redesigned to comply with the new identity guidelines of NXP Semiconductors.
- Legal texts have been adapted to the new company name where appropriate.
- Family specification included 74HC_HCT193_CNV v.2 19970828 Product specification - -
Product data sheet Rev. 4 — 24 June 2013 28 of 30 NXP Semiconductors 74HC193; 74HCT193 Presettable synchronous 4-bit binary up/down counter 16. Legal information
16.1 Data sheet status
[1] Please consult the most recently issued document before initiating or completing a design. [2] The term ‘short data sheet’ is explained in section “Definitions”. [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com.
16.2 Definitions
Draft — The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet — A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. Product specification — The information and data provided in a Product data sheet shall define the specification of the product as agreed between NXP Semiconductors and its customer, unless NXP Semiconductors and customer have explicitly agreed otherwise in writing. In no event however, shall an agreement be valid in which the NXP Semiconductors product is deemed to offer functions and qualities beyond those described in the Product data sheet.
16.3 Disclaimers
Limited warranty and liability — Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. NXP Semiconductors takes no responsibility for the content in this document if provided by an information source outside of NXP Semiconductors. In no event shall NXP Semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Notwithstanding any damages that customer might incur for any reason whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of NXP Semiconductors. Right to make changes — NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use — NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors and its suppliers accept no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk. Applications — Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Customers are responsible for the design and operation of their applications and products using NXP Semiconductors products, and NXP Semiconductors accepts no liability for any assistance with applications or customer product design. It is customer’s sole responsibility to determine whether the NXP Semiconductors product is suitable and fit for the customer’s applications and products planned, as well as for the planned application and use of customer’s third party customer(s). Customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. NXP Semiconductors does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer’s applications or products, or the application or use by customer’s third party customer(s). Customer is responsible for doing all necessary testing for the customer’s applications and products using NXP Semiconductors products in order to avoid a default of the applications and the products or of the application or use by customer’s third party customer(s). NXP does not accept any liability in this respect. Limiting values — Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the device. Limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the Recommended operating conditions section (if present) or the Characteristics sections of this document is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. Terms and conditions of commercial sale — NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms , unless otherwise agreed in a valid written individual agreement. In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. NXP Semiconductors hereby expressly objects to applying the customer’s general terms and conditions with regard to the purchase of NXP Semiconductors products by customer. No offer to sell or license — Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification.
Product data sheet Rev. 4 — 24 June 2013 29 of 30 NXP Semiconductors 74HC193; 74HCT193 Presettable synchronous 4-bit binary up/down counter Export control — This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from competent authorities. Non-automotive qualified products — Unless this data sheet expressly states that this specific NXP Semiconductors product is automotive qualified, the product is not suitable for automotive use. It is neither qualified nor tested in accordance with automotive testing or application requirements. NXP Semiconductors accepts no liability for inclusion and/or use of non-automotive qualified products in automotive equipment or applications. In the event that customer uses the product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall use the product without NXP Semiconductors’ warranty of the product for such automotive applications, use and specifications, and (b) whenever customer uses the product for automotive applications beyond NXP Semiconductors’ specifications such use shall be solely at customer’s own risk, and (c) customer fully indemnifies NXP Semiconductors for any liability, damages or failed product claims resulting from customer design and use of the product for automotive applications beyond NXP Semiconductors’ standard warranty and NXP Semiconductors’ product specifications. Translations — A non-English (translated) version of a document is for reference only. The English version shall prevail in case of any discrepancy between the translated and English versions.
16.4 Trademarks
Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. 17. Contact information For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com
NXP Semiconductors 74HC193; 74HCT193 Presettable synchronous 4-bit binary up/down counter © NXP B.V. 2013. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com Date of release: 24 June 2013 Document identifier: 74HC_HCT193 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section ‘Legal information’. 18. Contents