74F620 PHILIPS

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 12

Technical content

/C0109 /C0110 /C0114 74F620 Octal bus transceiver, inverting (3tate) 74F623 Octal bus transceiver, non–inverting (3tate) Product specification IC15 Data Handbook

1989 Apr 06

Philips Semiconductors Product specification 74F620/74F623Transceivers 74F620 Octal Bus Transceiver, Inverting (3-State) 74F623 Octal Bus Transceiver, Non-Inverting (3-State)

21990 Apr 6 853–0379 96249

FEATURES

  • High-impedance NPN base inputs for reduced loading (70µA in High and Low states)
  • Ideal for applications which require high output drive and minimal bus loading
  • Octal bidirectional bus interface
  • 3-State buffer outputs sink 64mA and source 15mA
  • 74F620, inverting
  • 74F623, non-inverting

DESCRIPTION

The 74F620 is an octal transceiver featuring inverting 3-State bus-compatible outputs in both send and receive directions. The outputs are capable of sinking 64mA and sourcing up to 15mA, providing very good capacitive drive characteristics. The 74F623 is a non-inverting version of the 74F620. These octal bus transceivers are designed for asynchronous two-way communication between data buses. The control function implementation allows for maximum flexibility in timing. These devices allow data transmission from the A bus to the B bus or from the B bus to the A bus depending upon the logic levels at the Enable inputs (OEBA and OEAB). The Enable inputs can be used to disable the device so that the buses are effectively isolated. The dual-enable configuration gives the 74F620 and 74F623 the capability to store data by the simultaneous enabling of OEBA and OEAB. Each output reinforces its input in this transceiver configuration. Thus, when both control inputs are enabled and all other data sources to the two sets of the bus lines are at high impedance, both sets of bus lines (16 in all) will remain in their last states. TYPE TYPICAL PROPAGATION DELAY TYPICAL SUPPLY CURRENT (TOTAL) 74F620 3.5ns 80mA 74F623 4.5ns 105mA

ORDERING INFORMATION

VCC = 5V ±10%, Tamb = 0°C to +70°C PKG DWG # 20-pin plastic DIP N74F620N, N74623N SOT146-1 20-pin plastic SOL N74F620D, N74623D SOT163-1 INPUT AND OUTPUT LOADING AND FAN-OUT TABLE PINS DESCRIPTION 74F(U.L.) HIGH/LOW LOAD VALUE HIGH/LOW A0 - A7, B0 - B7 Data inputs 3.5/1.16 70µA/70µA OEBA , OEAB Output Enable inputs 1.0/0.033 20µA/20µA A0 - A7 Data outputs 150/40 3mA/24mA B0 - B7 Data outputs 750/106.7 15mA/64mA NOTE: One (1.0) FAST unit load is defined as: 20µA in the High state and 0.6mA in the Low state. PIN CONFIGURATION – 74F620 10 11

1 VCC

PIN CONFIGURATION – 74F623 10 11

Philips Semiconductors Product specification 74F620/74F623Transceivers

1990 Apr 6 3

LOGIC SYMBOL – 74F620 18 17 16 15 B0 B1 B2 B3

1 OEAB

VCC = Pin 20 GND = Pin 10 14 13 12 B4 B5 B6 A2 A3 45 6 A4 A5 A6 A0 A1 LOGIC SYMBOL – 74F623 B0 B1 B2 B3 VCC = Pin 20 GND = Pin 10 B4 B5 B6 B7 A2 A3 45 6 A4 A5 A6 A0 A1 18 17 16 15 14 13 12 11 IEC/IEEE SYMBOL (IEEE/IEC) – 74F620 EN1 EN2 SF01127 IEC/IEEE SYMBOL (IEEE/IEC) – 74F623 SF01128 EN1 EN2

Philips Semiconductors Product specification 74F620/74F623Transceivers

1990 Apr 6 4

LOGIC DIAGRAM – 74F620 VCC = Pin 20 GND = Pin 10 SF01129 OEBA OEAB B3A3 119 LOGIC DIAGRAM – 74F623 VCC = Pin 20 GND = Pin 10 SF01130 OEBA OEAB B3A3 119 FUNCTION TABLE INPUTS OPERATING MODES OEBA OEAB 74F620 74F623 L L B data to A bus B data to A bus H H A data to B bus A data to B bus H L Z Z L H B data to A bus B data to A bus L H A data to B bus A data to B bus H = High voltage level L = Low voltage level X = Don’t care Z = High impedance “off” state

Philips Semiconductors Product specification 74F620/74F623Transceivers

1990 Apr 6 5

(Operation beyond the limits set forth in this table may impair the useful life of the device. Unless otherwise noted these limits are over the operating free-air temperature range.) SYMBOL PARAMETER RATING UNIT VCC Supply voltage –0.5 to +7.0 V VIN Input voltage –0.5 to +7.0 V IIN Input current –30 to +5 mA VOUT Voltage applied to output in High output state –0.5 to +VCC V IO Current applied to output in Low output state A0–A7 48 mA IOUT C urrent applied to output in Low output state B0–B7 128 mA Tamb Operating free-air temperature range 0 to +70 °C Tstg Storage temperature range –65 to +150 °C RECOMMENDED OPERATING CONDITIONS SYMBOL PARAMETER LIMITS UNITSYMBOL PARAMETER MIN NOM MAX UNIT VCC Supply voltage 4.5 5.0 5.5 V VIH High-level input voltage 2.0 V VIL Low-level input voltage 0.8 V IIK Input clamp current –18 mA IO High level output current A0–A7 –3 mA IOH High-level output current B0–B7 –15 mA IO Low level output current A0–A7 24 mA IOL Low-level output current B0–B7 64 mA Tamb Operating free-air temperature range 0 70 °C

Philips Semiconductors Product specification 74F620/74F623Transceivers

1990 Apr 6 6

DC ELECTRICAL CHARACTERISTICS (Over recommended operating free-air temperature range unless otherwise noted.) NO TAG LIMITS SYMBOL PARAMETER TEST CONDITIONS NO TAG MIN TYP NO TAG MAX UNIT A0–A7 IO = 3mA ±10%V CC 2.4 V VO High level output voltage B0–B7 VCC = MIN, VIL= MAX IOH = –3mA ±5%V CC 2.7 3.3 V VOH High-level output voltage B0 B7 VIL = MAX , VIH = MIN IO = 15mA ±10%V CC 2.0 V B0–B7 IOH = –15mA ±5%V CC 2.0 V A0 A7 IO = 24mA ±10%V CC 0.35 0.50 V VO Low level output voltage A0–A7 VCC = MIN, VIL= MAX IOL = 24mA ±5%V CC 0.35 0.50 V VOL Low-level output voltage B0 B7 VIL = MAX , VIH = MIN, IOL = 48mA ±10%V CC 0.38 0.55 V B0–B7 IOL = 64mA ±5%V CC 0.42 0.55 V VIK Input clamp voltage VCC = MIN, II = IIK –0.73 –1.2 V II Input current at maximum input voltage OEBA , OEAB VCC = 0.0V, VI = 7.0V 100 µA I in ut voltage others VCC = 5.5V, VI = 5.5V 1 mA IIH High-level input current OEBA , OEAB VCC = MAX, VI = 2.7V 20 µA IIL Low-level input current OEAB only VCC = MAX, VI = 0.5V –20 µA IOZH +IIH Off-state output current, High-level of voltage appliedA0–A7 VCC = MAX, VI = 2.7V 70 µA IOZL +IIL Off-state output current, Low-level of voltage applied B0–B7 VCC = MAX, VI = 0.5V –70 µA IOS Short-circuit output cur- NO TAG A0–A7 VCC = MAX –60 –150 mA IOS rentNO TAG B0–B7 VCC = MAX –100 –225 mA ICCH OEBA =OEAB=4.5V; A0–A7=GND 70 92 mA 74F620 ICCL VCC = MAX OEBA =OEAB=4.5V; A0–A7=4.5V 84 110 mA ICC Supply current ICCZ OEAB=GND; OEBA =A0–A7=4.5V 84 110 mA ICC y (total) ICCH OEBA =OEAB=4.5V; A0–A7=4.5V 110 140 mA 74F623 ICCL VCC = MAX OEBA =OEAB=4.5V; A0–A7=GND 110 140 mA ICCZ OEAB=GND; OEBA =A0–A7=4.5V 99 130 mA NOTES: 1. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions for the applicable type. 2. All typical values are at VCC = 5V, Tamb = 25°C. 3. Not more than one output should be shorted at a time. For testing IOS , the use of high-speed test apparatus and/or sample-and-hold techniques are preferable in order to minimize internal heating and more accurately reflect operational values. Otherwise, prolonged shorting of a High output may raise the chip temperature well above normal and thereby cause invalid readings in other parameter tests. In any sequence of parameter tests, IOS tests should be performed last.

Philips Semiconductors Product specification 74F620/74F623Transceivers

1990 Apr 6 7

AC ELECTRICAL CHARACTERISTICS – 74F620 LIMITS SYMBOL PARAMETER TEST CONDITION VCC = +5V Tamb = +25°C C L = 50pF, RL = 500Ω VCC = +5V ± 10% Tamb = 0°C to +70°C C L = 50pF, RL = 500Ω UNIT MIN TYP MAX MIN MAX tPLH tPHL Propagation delay An to Bn Waveform 2 2.5 1.0 4.5 2.5 6.5 4.5 2.0 1.0 7.5 5.0 ns tPLH tPHL Propagation delay Bn to An Waveform 2 2.5 1.0 4.5 2.5 6.5 4.5 2.0 1.0 7.5 5.0 ns tPZH tPZL Output Enable time to High or Low level, OEBA to An Waveform 3 Waveform 4 3.0 4.0 7.5 7.5 10.5 10.5 2.5 3.5 11.5 11.5 ns tPHZ tPLZ Output Disable time to High or Low level, OEBA to An Waveform 3 Waveform 4 2.5 2.0 4.5 4.5 7.5 7.0 2.0 1.5 8.0 7.5 ns tPZH tPZL Output Enable time to High or Low level, OEAB to Bn Waveform 3 Waveform 4 4.5 4.5 7.5 7.5 10.5 10.0 4.0 4.0 11.5 11.0 ns tPHZ tPLZ Output Disable time to High or Low level, OEAB to Bn Waveform 3 Waveform 4 3.0 4.0 6.5 6.5 9.5 9.5 2.5 3.5 10.5 10.5 ns AC ELECTRICAL CHARACTERISTICS – 74F623 LIMITS SYMBOL PARAMETER TEST CONDITION VCC = +5V Tamb = +25°C C L = 50pF, RL = 500Ω VCC = +5V ± 10% Tamb = 0°C to +70°C C L = 50pF, RL = 500Ω UNIT MIN TYP MAX MIN MAX tPLH tPHL Propagation delay An to Bn Waveform 1 2.0 3.0 4.0 5.0 5.5 7.0 2.0 2.5 6.5 7.5 ns tPLH tPHL Propagation delay Bn to An Waveform 1 2.0 2.5 4.0 4.5 5.5 6.5 2.0 2.5 6.5 7.5 ns tPZH tPZL Output Enable time to High or Low level, OEBA to An Waveform 3 Waveform 4 5.0 5.0 8.5 7.5 10.5 9.5 5.0 5.0 12.0 10.0 ns tPHZ tPLZ Output Disable time to High or Low level, OEBA to An Waveform 3 Waveform 4 2.5 2.5 4.5 4.5 6.5 6.5 2.5 2.5 7.5 7.0 ns tPZH tPZL Output Enable time to High or Low level, OEAB to Bn Waveform 3 Waveform 4 5.0 4.5 8.0 7.0 10.0 9.0 5.0 4.5 11.5 9.5 ns tPHZ tPLZ Output Disable time to High or Low level, OEAB to Bn Waveform 3 Waveform 4 3.0 4.0 6.0 7.0 8.5 9.0 3.0 4.0 10.0 10.0 ns

Philips Semiconductors Product specification 74F620/74F623Transceivers

1990 Apr 6 8

For all waveforms, VM = 1.5V. VMVM VMVM Bn or An An or Bn tPLHtPHL SF01131 Waveform 1. For Inverting Outputs VMVM VMVM Bn or An An or Bn tPLH tPHL SF01132 Waveform 2. For Non-Inverting Outputs VM VM VM tPHZtPZH VOH -0.3V SF01133 An or Bn OEBA OEAB Waveform 3. 3-State Output Enable Time to High Level and Output Disable Time from High Level VM VM VM tPLZtPZL VOL +0.3V An or Bn OEBA SF01134 OEAB Waveform 4. 3-State Output Enable Time to Low Level and Output Disable Time from Low Level TEST CIRCUIT AND WAVEFORMS tw 90% VM 10% 90% VM 10% 90% VM 10% 90% VM 10% NEGATIVE PULSE POSITIVE PULSE tw AMP (V) tTHL (tf ) INPUT PULSE REQUIREMENTS rep. rate tw tTLH tTHL 1MHz 500ns 2.5ns 2.5ns Input Pulse Definition VCC family 74F D.U.T.PULSE GENERATOR R LC LR T VIN VOUT Test Circuit for 3-State Outputs DEFINITIONS: R L = Load resistor; see AC electrical characteristics for value. C L = Load capacitance includes jig and probe capacitance; see AC electrical characteristics for value. R T = Termination resistance should be equal to ZOUT of pulse generators. tTHL (tf ) tTLH (tr ) tTLH (tr ) AMP (V) amplitude 3.0V 1.5V VM R L 7.0V SF00777 TEST SWITCH tPLZ closed tPZL closed All other open SWITCH POSITION

Philips Semiconductors Product specification 74F620, 74F623Transceivers

1990 Apr 06 9

DIP20: plastic dual in-line package; 20 leads (300 mil) SOT146-1

Philips Semiconductors Product specification 74F620, 74F623Transceivers

1990 Apr 06 10

SO20: plastic small outline package; 20 leads; body width 7.5 mm SOT163-1

Philips Semiconductors Product specification 74F620, 74F623Transceivers

1990 Apr 06 11

Philips Semiconductors Product specification 74F620, 74F623Transceivers yyyy mmm dd 12 Definitions Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Disclaimers Life support — These products are not designed for use in life support appliances, devices or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes — Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Philips Semiconductors

811 East Arques Avenue

P.O. Box 3409 Sunnyvale, California 94088–3409 Telephone 800-234-7381  Copyright Philips Electronics North America Corporation 1998 All rights reserved. Printed in U.S.A. print code Date of release: 10-98 Document order number: 9397-750-05146 /C0109 /C0110 /C0114 Data sheet status Objective specification Preliminary specification Product specification Product status Development Qualification Production Definition [1] This data sheet contains the design target or goal specifications for product development. Specification may change in any manner without notice. This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips Semiconductors reserves the right to make chages at any time without notice in order to improve design and supply the best possible product. This data sheet contains final specifications. Philips Semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. Data sheet status [1] Please consult the most recently issued datasheet before initiating or completing a design.