74F50729 PHILIPS

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 12

Technical content

/C0109 /C0110 /C0114 74F50729 Synchronizing dual D-type flip-flop with edge-triggered set and reset with metastable immune characteristics Product specification IC15 Data Handbook

1990 Sep 14

Philips Semiconductors Product specification 74F50729Synchronizing dual D-type flip-flop with edge-triggered set and reset and metastable immune characteristics

21990 Sep 14 853-1390 00420

FEATURES

  • Metastable immune characteristics
  • Output skew less than 1.5ns
  • High source current (IOH = 15mA) ideal for clock driver

applications

  • See 74F5074 for synchronizing dual D–type flip–flop
  • See 74F50109 for synchronizing dual J–K positive edge–triggered flip–flop
  • See 74F50728 for synchronizing cascaded dual D–type flip–flop
  • Industrial temperature range available (–40°C to +85°C)

DESCRIPTION

The 74F50729 is a dual positive edge–triggered D–type featuring individual data, clock, set and reset inputs; also true and complementary outputs. The 74F50729 is designed so that the outputs can never display a metastable state due to setup and hold time violations. If setup time and hold time are violated the propagation delays may be extended beyond the specifications but the outputs will not glitch or display a metastable state. Typical metastability parameters for the 74F50729 are: τ ≅ 135ps and τ ≅ 9.8 X 10 6 sec where τ represents a function of the rate at which a latch in a metastable state resolves that condition and T o represents a function of the measurement of the propensity of a latch to enter a metastable state. Set (SDn) and reset (RDn) are asynchronous positive–edge triggered inputs and operate independently of the clock (CPn) input. Data must be stable just one setup time prior to the low–to–high transition of the clock for guaranteed propagation delays. Clock triggering occurs at a voltage level and is not directly related to the transition time of the positive–going pulse. Following the hold time interval, data at the Dn input may be changed without affecting the levels of the output. PIN CONFIGURATION GND VCC SD1 Q 1 CP1 RD1 RD0 Q 0 CP0 SD0 SF00611 TYPE TYPICAL fMAX TYPICAL SUPPLY CURRENT (TOTAL) 74F50729 120 MHz 19mA

ORDERING INFORMATION

COMMERCIAL RANGE INDUSTRIAL RANGE DESCRIPTION VCC = 5V ±10%, VCC = 5V ±10%, PKG DWG # Tamb = 0°C to +70°C Tamb = –40°C to +85°C 14–pin plastic DIP N74F50729N I74F50729N SOT27-1 14–pin plastic SO N74F50729D I74F50729D SOT108-1 INPUT AND OUTPUT LOADING AND FAN OUT TABLE PINS DESCRIPTION 74F (U.L.) HIGH/ LOW LOAD VALUE HIGH/ LOW D0, D1 Data inputs 1.0/0.417 20µA/250µA CP0, CP1 Clock inputs (active rising edge) 1.0/1.0 20µA/20µA SD0, SD1 Set inputs (active rising edge) 1.0/1.0 20µA/20µA RD0, RD1 Reset inputs (active rising edge) 1.0/1.0 20µA/20µA Q0, Q1, Q0, Q1 Data outputs 750/33 15mA/20mA NOTE: One (1.0) FAST unit load is defined as: 20µA in the high state and 0.6mA in the low state.

1990 Sep 14 3

describe characteristics of some of the products in its family. which will not glitch or display metastable immune characteristics. the metastability characteristics of the part defined by τ and T0. types represent state–of–the–art TTL technology. because input events consist of both of low and high transitions. formula the actual MTBF is 1.51 X 1010 seconds or about 480 years. Figure 1. Test Setup

1990 Sep 14 4

Figure 2. 74F74 Q output triggered by Q output, setup and hold times violated Figure 3. 74F74 Q output triggered by Q output, setup and hold times violated

Philips Semiconductors Product specification 74F50729Synchronizing dual D-type flip-flop with edge-triggered set and reset and metastable immune characteristics

1990 Sep 14 5

MEAN TIME BETWEEN FAILURES (MTBF) VERSUS t’ 7891 0 1012 1011 1010 109 108 107 106 1014 1015 = fC fI t’ in nanoseconds MTBF in seconds one year 106 108 1010 1012 one week 10,000 years 100 years SF00589 NOTE: VCC = 5V, Tamb = 25°C, τ =135ps, To = 9.8 X 106 sec Figure 4. TYPICAL VALUES FOR τ AND T0 AT VARIOUS VCC S AND TEMPERATURES Tamb = 0°C Tamb = 25°C Tamb = 70°C VCC τ T0 τ T0 τ T0 5.5V 125ps 1.0 X 109 sec 138ps 5.4 X 106 sec 160ps 1.7 X 105 sec 5.0V 115ps 1.3 X 1010 sec 135ps 9.8 X 106 sec 167ps 3.9 X 104 sec 4.5V 115ps 3.4 X 1013 sec 132ps 5.1 X 108 sec 175ps 7.3 X 104 sec FUNCTION TABLE INPUTS OUTPUTS OPERATING SD R D CP D Q Q MODE ↑ ↑ X X H L Asynchronous set ↑ ↑ X X L H Asynchronous reset ↑ ↑ ↑ X NC NC Hold NOTES: 1. H = High–voltage level 2. h = High–voltage level one setup time prior to low–to–high clock transition 3. L = Low–voltage level 4. l = Low–voltage level one setup time prior to low–to–high clock transition 5. NC= No change from the previous setup 6. X = Don’t care 7. ↑ = Low–to–high clock transition 8. ↑ = Not low–to–high clock transition LOGIC DIAGRAM VCC = Pin 14 GND = Pin 7 4, 10 3, 11 SD CP Q5, 9 SF00614 2, 12 D 1, 13RD 6, 8 Q

Philips Semiconductors Product specification 74F50729Synchronizing dual D-type flip-flop with edge-triggered set and reset and metastable immune characteristics

1990 Sep 14 6

(Operation beyond the limit set forth in this table may impair the useful life of the device. Unless otherwise noted these limits are over the operating free air temperature range.) SYMBOL PARAMETER RATING UNIT VCC Supply voltage –0.5 to +7.0 V VIH Input voltage –0.5 to +7.0 V IIN Input current –30 to +5 mA VOUT Voltage applied to output in high output state –0.5 to VCC V IOUT Current applied to output in low output state 40 mA Tamb Operating free air temperature range Commercial range 0 to +70 °C Industrial range –40 to +85 °C Tstg Storage temperature range –65 to +150 °C RECOMMENDED OPERATING CONDITIONS LIMITS SYMBOL PARAMETER MIN NOM MAX UNIT VCC Supply voltage 4.5 5.0 5.5 V VIH High–level input voltage 2.0 V VIL Low–level input voltage 0.8 V IIk Input clamp current –18 mA IOH High–level output current VCC ± 10% –12 mA VCC ± 5% –15 mA IOL Low–level output current 20 mA Tamb Operating free air temperature range Commercial range 0 +70 °C Industrial range –40 +85 °C

Philips Semiconductors Product specification 74F50729Synchronizing dual D-type flip-flop with edge-triggered set and reset and metastable immune characteristics

1990 Sep 14 7

DC ELECTRICAL CHARACTERISTICS (Over recommended operating free-air temperature range unless otherwise noted.) SYMBOL PARAMETER TEST LIMITS UNIT CONDITIONS 1 MIN TY.2 MAX VOH High-level output voltage VCC = MIN, VIH = MIN IOH = MAX ±10%V CC 2.5 V VIL = MAX, ±5%V CC 2.7 3.4 V IOH = –15mA ±5%V CC 2.0 V VOL Low-level output voltage VCC = MIN, VIL = MAX, IOL = MAX ±10%V CC 0.30 0.50 V VIH = MIN ±5%V CC 0.30 0.50 V VIK Input clamp voltage VCC = MIN, II = IIK -0.73 -1.2 V II Input current at maximum input voltageVCC = MAX, VI = 7.0V 100 µA IIH High–level input current VCC = MAX, VI = 2.7V 20 µA IIL Low–level input current Dn VCC = MAX, VI = 0.5V -250 µA CPn, SDn, RDn –20 µA IOS Short–circuit output current3 VCC = MAX, VO = 2.25V -60 -150 mA ICC Supply current4 (total) VCC = MAX 19 27 mA NOTES: 1. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions for the applicable type and function table for operating mode. 2. All typical values are at VCC = 5V, Tamb = 25°C. 3. Not more than one output should be shorted at a time. For testing IOS , the use of high-speed test apparatus and/or sample-and-hold techniques are preferable in order to minimize internal heating and more accurately reflect operational values. Otherwise, prolonged shorting of a high output may raise the chip temperature well above normal and thereby cause invalid readings in other parameter tests. In any sequence of parameter tests, IOS tests should be performed last. 4. Measure ICC with the clock input grounded and all outputs open, then with Q and Q outputs high in turn. AC ELECTRICAL CHARACTERISTICS LIMITS Tamb = +25°C Tamb = 0°C to +70°C Tamb = –40°C to +85°C SYMBOL PARAMETER TEST VCC = +5.0V VCC = +5.0V ± 10% VCC = +5.0V ± 10% UNIT CONDITION C L = 50pF, R L = 500Ω C L = 50pF, R L = 500Ω C L = 50pF, R L = 500Ω MIN TYP MAX MIN MAX MIN MAX fmax Maximum clock frequency Waveform 1 105 120 85 75 ns tPLH tPHL Propagation delay CPn to Qn or Qn Waveform 1 2.0 2.0 3.9 3.9 6.0 6.0 1.5 2.0 6.5 6.5 1.5 2.0 7.0 6.5 ns tPLH tPHL Propagation delay SDn RDn to Qn or Qn Waveform 2 2.0 3.0 4.0 5.0 6.5 7.5 1.5 2.0 7.5 8.0 1.5 2.0 7.5 8.0 ns tok(o) Output skew1, 2 Waveform 4 1.5 1.5 1.5 ns NOTES: 1. | tPLH actual –tPHL actual | for any one output compared to any other output where N and M are either LH or HL. 2. Skew lines are valid only under same conditions (temperature, VCC , loading, etc.,).

Philips Semiconductors Product specification 74F50729Synchronizing dual D-type flip-flop with edge-triggered set and reset and metastable immune characteristics

1990 Sep 14 8

Tamb = +25°C Tamb = 0°C to +70°C Tamb = –40°C to +85°C SYMBOL PARAMETER TEST VCC = +5.0V VCC = +5.0V ± 10% VCC = +5.0V ± 10% UNIT CONDITION C L = 50pF, R L = 500Ω C L = 50pF, R L = 500Ω C L = 50pF, R L = 500Ω MIN TYP MAX MIN MAX MIN MAX tsu (H) tsu(L) Setup time, high or low Dn to CPn Waveform 1 1.5 1.5 2.0 2.0 2.0 2.0 ns th (H) th (L) Hold time, high or low Dn to CPn Waveform 1 1.0 1.0 1.5 1.5 1.5 1.5 ns tw (H) tw (L) CPn pulse width, high or low Waveform 2 3.0 4.0 3.5 6.0 3.5 6.0 ns tw (L) SDn, RDn pulse width, low Waveform 3 3.5 4.0 4.0 ns trec Recovery time SDn, RDn to CPn Waveform 3 6.0 6.5 6.5 ns trec Recovery time SDn to RDn or RDn to SDn Waveform 3 6.0 1.0 1.0 ns AC WAVEFORMS For all waveforms, VM = 1.5V. The shaded areas indicate when the input is permitted to change for predictable output performance. VMVM CPn VM VM VM VM VM VM tsu(H) th(H) Dn Qn VM tw (H) 1/fmax tsu(L) t h(L) VMVM tPLH Q n tw (L) tPHL tPHLtPLH SF00049 Waveform 1. Propagation delay for data to output, data setup time and hold times, and clock width, and maximum clock frequency SDn or RDn VM VM trec CPn SF00603 Waveform 3. Recovery time for set or reset to output VMVM R Dn VM Qn VM VMVM tPLH Q n tw (L) tPHL tPHLtPLH SDn VMVM tw (L) SF00050 Waveform 2. Propagation delay for set and reset to output, set and reset pulse width Qn, Qn VM VM tsk(o) Q n, Qn SF00590 Waveform 4. Output skew

Philips Semiconductors Product specification 74F50729Synchronizing dual D-type flip-flop with edge-triggered set and reset and metastable immune characteristics

1990 Sep 14 9

TEST CIRCUIT AND WAVEFORMS tw 90% VM 10% 90% VM 10% 90% VM 10% 90% VM 10% NEGATIVE PULSE POSITIVE PULSE tw AMP (V) tTHL (tf ) INPUT PULSE REQUIREMENTS rep. rate tw tTLH tTHL 1MHz 500ns 2.5ns 2.5ns Input Pulse Definition VCC family 74F D.U.T.PULSE GENERATOR R LC LR T VIN VOUT Test Circuit for Totem-Pole Outputs DEFINITIONS: R L = Load resistor; see AC ELECTRICAL CHARACTERISTICS for value. C L = Load capacitance includes jig and probe capacitance; see AC ELECTRICAL CHARACTERISTICS for value. R T = Termination resistance should be equal to ZOUT of pulse generators. tTHL (tf ) tTLH (tr ) tTLH (tr ) AMP (V) amplitude 3.0V 1.5V VM SF00006

Philips Semiconductors Product specification 74F50729Synchronizing dual D-type flip-flop with edge-triggered set and reset and metastable immune characteristics

1990 Sep 14 10

DIP14: plastic dual in-line package; 14 leads (300 mil) SOT27-1

Philips Semiconductors Product specification 74F50729Synchronizing dual D-type flip-flop with edge-triggered set and reset and metastable immune characteristics

1990 Sep 14 11

SO14: plastic small outline package; 14 leads; body width 3.9 mm SOT108-1

Philips Semiconductors Product specification 74F50729Synchronizing dual D-type flip-flop with edge-triggered set and reset and metastable immune characteristics yyyy mmm dd 12 Definitions Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Disclaimers Life support — These products are not designed for use in life support appliances, devices or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes — Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Philips Semiconductors

811 East Arques Avenue

P.O. Box 3409 Sunnyvale, California 94088–3409 Telephone 800-234-7381  Copyright Philips Electronics North America Corporation 1998 All rights reserved. Printed in U.S.A. print code Date of release: 10-98 Document order number: 9397-750-05216 /C0109 /C0110 /C0114 Data sheet status Objective specification Preliminary specification Product specification Product status Development Qualification Production Definition [1] This data sheet contains the design target or goal specifications for product development. Specification may change in any manner without notice. This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips Semiconductors reserves the right to make chages at any time without notice in order to improve design and supply the best possible product. This data sheet contains final specifications. Philips Semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. Data sheet status [1] Please consult the most recently issued datasheet before initiating or completing a design.