74F395 PHILIPS
Document overview
- Manufacturer or author: Provided By digicamel.com
- PDF pages: 7
Technical content
Philips Semiconductors Product specification 74F3954-bit cascadable shift register (3-State)
11990 Oct 23 853–0370 00780
FEATURES
- 4-bit parallel load shift register
- Independent 3-State buffer outputs, Q0–Q3
- Separate Qs output for serial expansion
- Asynchronous Master Reset
DESCRIPTION
The 74F395 is a 4-bit Shift Register with serial and parallel synchronous operating modes and 3-State buffer outputs. The shifting and loading operations are controlled by the state of the Parallel Enable (PE) input. When PE is High, data is loaded from the Parallel Data inputs (D0–D3) into the register synchronous with the High-to-Low transition of the Clock input (CP). When PE is Low, the data at the Serial Data input (Ds) is loaded into the Q0 flip-flop, and the data in the register is shifted one bit to the right in the direction (Q0 Q1 Q2 Q3) synchronous with the negative clock transition. The PE and Data inputs are fully edge-triggered and must be stable one setup prior to the High-to-Low transition of the clock. The Master Reset (MR) is an asynchronous active-Low input. When Low, the MR overrides the clock and all other inputs and clears the register. The 3-state output buffers are designed to drive heavily loaded 3-State buses, or large capacitive loads. The active-Low Output Enable (OE) controls all four 3-State buffers independent of the register operation. The data in the register appears at the outputs when OE is Low. The outputs are in High impedance “OFF” state, which means they will neither drive nor load the bus when OE is High. The output from the last stage is brought out separately. This output (Qs) is tied to the Serial Data input (Ds) of the next register for serial expansion applications. The Qs output is not affected by the 3-State buffer operation. PIN CONFIGURA TION 107 PE VCC Qs CP MR Ds SF00940 98GND OE TYPE TYPICAL fMAX TYPICAL SUPPL Y CURRENT (TOTAL) 74F395 120MHz 32mA
ORDERING INFORMATION
DESCRIPTION COMMERCIAL RANGE VCC = 5V ±10%, Tamb = 0°C to +70°C 16-pin plastic DIP N74F395N 16-pin plastic SO N74F395D INPUT AND OUTPUT LOADING AND F AN-OUT TABLE PINS DESCRIPTION 74F (U.L.) HIGH/LOW LOAD VALUE HIGH/LOW D0 – D3 Data inputs 1.0/1.0 20µA/0.6mA Ds Serial data input 1.0/1.0 20µA/0.6mA PE Parallel Enable input 1.0/1.0 20µA/0.6mA MR Master Reset input (active Low) 1.0/1.0 20µA/0.6mA OE Output Enable input (active Low) 1.0/1.0 20µA/0.6mA CP Clock Pulse input (active falling edge) 1.0/1.0 20µA/0.6mA Qs Serial expansion output 50/33 1.0mA/20mA Q0–Q3 Data outputs (3-State) 150/40 3.0mA/24mA NOTE: One (1.0) FAST unit load is defined as: 20µA in the High state and 0.6mA in the Low state.
Philips Semiconductors Product specification 74F3954-bit cascadable shift register (3-State)
1990 Oct 23 2
VCC = Pin 16 GND = Pin 8 3 4 5 6 D0 D1 D2 D3 Ds 11Qs IEC/IEEE SYMBOL (IEEE/IEC) 2,3D SF00942 1,3D R M1[LOAD] C3/2 SRG4 EN4 M2[SHIFT] 1,3D LOGIC DIAGRAM VCC = Pin 16 GND = Pin 8 SF00943 R Q CLR CP QS R Q CLR CP QS R Q CLR CP QS R Q CLR CP QS Qs OE CP MR PE Ds
Philips Semiconductors Product specification 74F3954-bit cascadable shift register (3-State)
1990 Oct 23 3
MODE SELECT–FUNCTION T ABLE INPUTS OUTPUTS REGISTER OPERATING MODESMR CP PE Ds Dn Q0 Q1 Q2 Q3 OPERATING MODES L X X X X L L L L Reset (clear) H /C0035 l l X L q0 q1 q2 Shift right H /C0035 l h X H q0 q1 q2 Shift right H /C0035 h X l L L L L Parallel load H /C0035 h X h H H H H Parallel load INPUTS OUTPUTS 3-STATE BUFFER OPERATING MODESOE Qn (Register) Q0, Q1, Q2, Q3 Qs OPERATING MODES L L L L Read L H H H Read H L Z L Disable buffers H H Z H Disable buffers H = High voltage level h = High voltage level one set-up time prior to the High-to-Low clock transition L = Low voltage level l = Low voltage level one set-up time prior to the High-to-Low clock transition qn = Lower case letters indicate the state of the referenced input (or output) one set-up time prior to the High-to-Low clock transition X = Don’t care Z = High impedance “OFF” state /C0035 = High-to-Low clock transition ABSOLUTE MAXIMUM RA TINGS (Operation beyond the limits set forth in this table may impair the useful life of the device. Unless otherwise noted these limits are over the operating free-air temperature range.) SYMBOL PARAMETER RATING UNIT VCC Supply voltage –0.5 to +7.0 V VIN Input voltage –0.5 to +7.0 V IIN Input current –30 to +5 mA VOUT Voltage applied to output in High output state –0.5 to +5.5 V IOUT Current applied to output in Low output state Qs 40 mA IOUT Current applied to output in Low output state Q0–Q3 48 mA Tamb Operating free-air temperature range 0 to +70 °C Tstg Storage temperature range –65 to +150 °C RECOMMENDED OPERA TING CONDITIONS SYMBOL PARAMETER LIMITS UNITSYMBOL PARAMETER MIN NOM MAX UNIT VCC Supply voltage 4.5 5.0 5.5 V VIH High-level input voltage 2.0 V VIL Low-level input voltage 0.8 V IIK Input clamp current –18 mA IOH High-level output current Qs –1 mA IOH High-level output current Q0–Q3 –3 mA IOL Low-level output current Qs 20 mA IOL Low-level output current Q0–Q3 24 mA Tamb Operating free-air temperature range 0 70 °C
Philips Semiconductors Product specification 74F3954-bit cascadable shift register (3-State)
1990 Oct 23 4
DC ELECTRICAL CHARACTERISTICS (Over recommended operating free-air temperature range unless otherwise noted.) SYMBOL PARAMETER TEST CONDITIONS 1 LIMITS UNITSYMBOL PARAMETER TEST CONDITIONS 1 MIN TYP 2 MAX UNIT VOH High-level output voltage Qs VCC = MIN, VIL = MAX, VIH=MIN IOH =–1mA ±10%V CC 2.5 V VOH High-level output voltage Qs VCC = MIN, VIL = MAX, VIH=MIN IOH =–1mA ±5%V CC 2.7 3.4 V VOH High-level output voltage Q0–Q3 VIL = MAX, VIH=MIN IOH =–3mA ±10%V CC 2.4 V Q0–Q3 IH=MIN IOH =–3mA ±5%V CC 2.7 V VOL Low-level output voltage VCC = MIN, VIL = MAX, VIH = MIN, IOL = MAX ±10%V CC 0.35 0.50 V VOL Low-level output voltage VIL = MAX, VIH = MIN, IOL = MAX ±5%V CC 0.35 0.50 V VIK Input clamp voltage VCC = MIN, II = IIK –0.73 –1.2 V II Input current at maximum input voltageVCC = MAX, VI = 7.0V 100 µA IIH High-level input current VCC = MAX, VI = 2.7V 20 µA IIL Low-level input current VCC = MAX, VI = 0.5V –0.6 mA IOZH Off-state output current High level of voltage applied Q0–Q3 only VCC = MAX, VO = 2.7V 50 µA IOZL Off-state output current Low level of voltage applied Q0–Q3 only VCC = MAX, VO = 0.5V –50 µA IOS Short-circuit output current3 VCC = MAX –60 –150 mA ICC Supply current (total) ICCH VCC = MAX MR =PE=Dn=Ds=4.5V, OE =GND, CP= /C0035 33 48 mA ICC Supply current (total) ICCL VCC = MAX MR =OE =Dn=Ds=GND, PE=4.5V, CP=/C0035 35 50 mA ICCZ MR =Dn=Ds=GND, OE =4.5V 32 46 mA NOTES: 1. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions for the applicable type. 2. All typical values are at VCC = 5V, Tamb = 25°C. 3. Not more than one output should be shorted at a time. For testing IOS , the use of high-speed test apparatus and/or sample-and-hold techniques are preferable in order to minimize internal heating and more accurately reflect operational values. Otherwise, prolonged shorting of a High output may raise the chip temperature well above normal and thereby cause invalid readings in other parameter tests. In any sequence of parameter tests, IOS tests should be performed last.
Philips Semiconductors Product specification 74F3954-bit cascadable shift register (3-State)
1990 Oct 23 5
AC ELECTRICAL CHARACTERISTICS SYMBOL PARAMETER TEST CONDITION LIMITS UNITSYMBOL PARAMETER TEST CONDITION VCC = +5V Tamb = +25°C C L = 50pF, RL = 500Ω VCC = +5V ± 10% Tamb = 0°C to +70°C C L = 50pF, RL = 500Ω UNIT MIN TYP MAX MIN MAX fMAX Maximum clock frequency W aveform 1 105 120 MHz tPLH tPHL Propagation delay CP to Qn W aveform 1 3.5 5.0 6.0 8.0 8.5 11.0 3.5 5.0 9.5 11.5 ns tPLH tPHL Propagation delay CP to Qs W aveform 1 4.5 5.5 6.0 7.5 8.5 10.0 4.0 5.0 9.5 10.5 ns tPHL Propagation delay tPHL Propagation delay tPZH tPZL Output Enable time to High or Low level W aveform 4 W aveform 5 4.0 3.5 6.5 6.0 9.0 8.0 4.0 3.5 10.0 8.5 ns tPHZ tPLZ Output Disable time from High or Low level W aveform 4 W aveform 5 1.0 1.0 2.5 3.5 4.5 5.5 1.0 1.0 5.5 6.5 ns AC SETUP REQUIREMENTS SYMBOL PARAMETER TEST CONDITION LIMITS UNITSYMBOL PARAMETER TEST CONDITION VCC = +5V Tamb = +25°C C L = 50pF, RL = 500Ω VCC = +5V ± 10% Tamb = 0°C to +70°C C L = 50pF, RL = 500Ω UNIT MIN TYP MAX MIN MAX ts(H) ts(L) Setup time, High or Low Dn to CP W aveform 3 2.5 1.5 3.0 2.0 ns th(H) th(L) Hold time, High or Low Dn to CP W aveform 3 1.5 1.5 1.5 1.5 ns ts(H) ts(L) Setup time, High or Low PE to CP W aveform 3 6.5 6.0 7.0 6.5 ns th(H) th(L) Hold time, High or Low PE to CP W aveform 3 0 0 ns tW (H) tW (L) CP Pulse width High or Low W aveform 1 5.0 4.0 5.5 4.5 ns tW (L) MR Pulse width Low W aveform 2 2.5 3.0 ns tREC Recovery time MR to CP W aveform 2 6.0 7.0 ns
Philips Semiconductors Product specification 74F3954-bit cascadable shift register (3-State)
1990 Oct 23 6
For all waveforms, VM = 1.5V. The shaded areas indicate when the input is permitted to change for predictable output performance. VM VM VM 1/fMAX tPHL tw (L) Qn, Qs tw (H) VM CP tPLH SF00944 Waveform 1. Propagation Delay, Clock Input to Output, Clock Widths, and Maximum Clock Frequency VM VM VM tREC tPHL MR CP Qn, Qs VM tw (L) SF00945 Waveform 2. Master Reset Pulse Width, Master Reset to Output Delay, and Master Reset to Clock Recovery Time SF00946 VM VM VM VM VM VM PE CP VM VMDn ts th VMVM ts th ts th ts th Ds STABLE STABLE W aveform 3. Parallel Enable and Data Setup Time and Hold Time VM VM VM tPHZtPZH VOH -0.3V OE Qn SF00343 Waveform 4. 3-State Output Enable Time to High Level and Output Disable Time from High Level VM VM VM tPLZtPZL VOL +0.3V Qn OE SF00344 Waveform 5. 3-State Output Enable Time to Low Level and Output Disable Time from Low Level
Philips Semiconductors Product specification 74F3954-bit cascadable shift register (3-State)
1990 Oct 23 7
TEST CIRCUIT AND W AVEFORMS tw 90% VM 10% 90% VM 10% 90% VM 10% 90% VM 10% NEGATIVE PULSE POSITIVE PULSE tw AMP (V) tTHL (tf ) INPUT PULSE REQUIREMENTS rep. rate tw tTLH tTHL 1MHz 500ns 2.5ns 2.5ns Input Pulse Definition VCC family 74F D.U.T.PULSE GENERATOR R LC LR T VIN VOUT Test Circuit for 3-State Outputs and Totem-Pole Output (Qs) DEFINITIONS: R L = Load resistor; see AC electrical characteristics for value. C L = Load capacitance includes jig and probe capacitance; see AC electrical characteristics for value. R T = T ermination resistance should be equal to ZOUT of pulse generators. tTHL (tf ) tTLH (tr ) tTLH (tr ) AMP (V) amplitude 3.0V 1.5V VM R L 7.0V SF00957 TEST SWITCH tPLZ closed tPZL closed All other open SWITCH POSITION