74F393 PHILIPS

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 8

Technical content

/C0109 /C0110 /C0114 74F393 Dual 4-bit binary ripple counter Product specification IC15 Data Handbook

1988 Nov 01

Philips Semiconductors Product specification 74F393Dual 4-bit binary ripple counter

21988 Nov 01 853–0295 94977

FEATURES

  • Two 4-bit binary counters
  • Two Master Resets to clear each 4-bit counter individually

DESCRIPTION

The 74F393 is a Dual Ripple Counter with separate Clock (CPn) and Master Reset (MR) inputs to each counter. The two counters are identified by the “a” and “b” suffixes in the pin configuration. The operation of each half of the 74F393 is the same. The counters are triggered by a High-to-Low transition of the Clock (CP a and CPb) inputs. The counter outputs are internally connected to provide Clock inputs to succeeding stages. The outputs of the ripple counter do not change synchronously and should not be used for high speed address decoding. The Master Resets (MR a and MRb) are active High asynchronous inputs; one for each 4-bit counter. A High level in the MR input overrides the Clock and sets the outputs Low. PIN CONFIGURATION GND VCC Q1b Q2b Q3b Q0b CP b MRb CP a MRa Q3a Q0a Q1a Q2a SF00704 TYPE TYPICAL fMAX TYPICAL SUPPLY CURRENT (TOTAL) 74F393 125MHz 40mA

ORDERING INFORMATION

VCC = 5V ±10%, Tamb = 0°C to +70°C PKG DWG # 14-pin plastic DIP N74F393N SOT27-1 14-pin plastic SO N74F393D SOT108-1 INPUT AND OUTPUT LOADING AND FAN-OUT TABLE PINS DESCRIPTION 74F (U.L.) HIGH/LOW LOAD VALUE HIGH/LOW CP a, CPb Clock inputs 1.0/1.0 20µA/0.6mA MR a, MRb Master Reset inputs 1.0/1.0 20µA/0.6mA Q na – Qnb Data outputs 50/33.3 1.0mA/20mA NOTE: One (1.0) FAST unit load is defined as: 20µA in the High state and 0.6mA in the Low state. LOGIC SYMBOL

1 CP a

Q0a Q1a Q2a Q3a Q0b Q1b Q2b Q3b

2 MR a

VCC = Pin 14 GND = Pin 7 IEC/IEEE SYMBOL (IEEE/IEC) SF00706 CTR DIV 16 CT=0 CTR DIV 16 CT=0

Philips Semiconductors Product specification 74F393Dual 4-bit binary ripple counter

1988 Nov 01 3

3, 11 Q1n 4, 10 Q2n 5, 9 Q3n 6, 8 2, 12 CP n MRn VCC = Pin 14 GND = Pin 7 SF00707 CP Q R D J CP Q R D J CP Q R D J CP Q R D J1, 13 QKQ KQ KQK FUNCTION TABLE COUNT OUTPUTS COUNT Q 0n Q 1n Q 2n Q 3n

0 L L L L

1 H LLL

2 L HLL

3 H HLL

4 L L H L

5 H LHL

6 L HHL

7 H HHL

8 L L L H

9 H LLH

10 L HLH

11 H HLH

12 L L H H

13 H LHH

14 L HHH

15 H H H H

H = High voltage level transition L = Low voltage level ABSOLUTE MAXIMUM RATINGS (Operation beyond the limits set forth in this table may impair the useful life of the device. Unless otherwise noted these limits are over the operating free-air temperature range.) SYMBOL PARAMETER RATING UNIT VCC Supply voltage –0.5 to +7.0 V VIN Input voltage –0.5 to +7.0 V IIN Input current –30 to +5 mA VOUT Voltage applied to output in High output state –0.5 to VCC V IOUT Current applied to output in Low output state 40 mA Tamb Operating free-air temperature range 0 to +70 °C Tstg Storage temperature range –65 to +150 °C RECOMMENDED OPERATING CONDITIONS SYMBOL PARAMETER LIMITS UNITSYMBOL PARAMETER MIN NOM MAX UNIT VCC Supply voltage 4.5 5.0 5.5 V VIH High-level input voltage 2.0 V VIL Low-level input voltage 0.8 V IIK Input clamp current –18 mA IOH High-level output current –1 mA IOL Low-level output current 20 mA Tamb Operating free-air temperature range 0 70 °C

Philips Semiconductors Product specification 74F393Dual 4-bit binary ripple counter

1988 Nov 01 4

DC ELECTRICAL CHARACTERISTICS (Over recommended operating free-air temperature range unless otherwise noted.) SYMBOL PARAMETER TEST CONDITIONS 1 LIMITS UNITSYMBOL PARAMETER TEST CONDITIONS 1 MIN TYP 2 MAX UNIT VO High level output voltage VCC = MIN, VIL = MAX ±10%V CC 2.5 VVOH High-level output voltage VIH = MIN, IOH = MAX ±5%V CC 2.7 3.4 V VO Low level output voltage VCC = MIN, VIL = MAX ±10%V CC 0.30 0.50 VVOL Low-level output voltage VIH = MIN, IOL = MAX ±5%V CC 0.30 0.50 V VIK Input clamp voltage VCC = MIN, II = IIK –0.73 –1.2 V II Input current at maximum input voltageVCC = MAX, VI = 7.0V 100 µA IIH High-level input current VCC = MAX, VI = 2.7V 20 µA IIL Low-level input current VCC = MAX, VI = 0.5V –0.6 mA IOS Short-circuit output current3 VCC = MAX –60 –150 mA ICC Supply current (total) ICCH VCC = MAX 25 36 mA ICC Supply current (total) ICCL VCC = MAX 42 58 mA NOTES: 1. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions for the applicable type. 2. All typical values are at VCC = 5V, Tamb = 25°C. 3. Not more than one output should be shorted at a time. For testing IOS , the use of high-speed test apparatus and/or sample-and-hold techniques are preferable in order to minimize internal heating and more accurately reflect operational values. Otherwise, prolonged shorting of a High output may raise the chip temperature well above normal and thereby cause invalid readings in other parameter tests. In any sequence of parameter tests, IOS tests should be performed last. AC ELECTRICAL CHARACTERISTICS LIMITS SYMBOL PARAMETER TEST CONDITION VCC = +5V Tamb = +25°C C L = 50pF, RL = 500Ω VCC = +5V ± 10% Tamb = 0°C to +70°C C L = 50pF, RL = 500Ω UNIT MIN TYP MAX MIN MAX fMAX Maximum clock frequency Waveform 1 100 130 100 MHz tPLH tPHL Propagation delay CP n to Q0a or Q0b Waveform 1 3.5 5.0 5.5 7.0 8.0 10.0 3.5 5.0 9.0 10.5 ns tPLH tPHL Propagation delay CP n to Q1a, Q1b Waveform 1 5.0 7.5 7.0 9.5 10.0 12.0 4.5 7.0 13.0 13.0 ns tPLH tPHL Propagation delay CP n to Q2a, Q2b Waveform 1 8.0 9.5 10.0 11.5 13.0 14.5 7.0 9.0 15.0 15.5 ns tPLH tPHL Propagation delay CP n to Q3a, Q3b Waveform 1 10.5 12.0 12.5 14.0 15.5 16.5 10.0 11.5 17.0 17.5 ns tPHL Propagation delay MR to Qna, Qnb

Philips Semiconductors Product specification 74F393Dual 4-bit binary ripple counter

1988 Nov 01 5

VCC = +5V Tamb = +25°C C L = 50pF, RL = 500Ω VCC = +5V ± 10% Tamb = 0°C to +70°C C L = 50pF, RL = 500Ω UNIT MIN TYP MAX MIN MAX tW (H) tW (L) CP n Pulse width High or Low Waveform 1 4.5 3.5 5.0 4.0 ns tW (H) MR Pulse width High Waveform 2 3.5 4.5 ns tREC Recovery time MR to CP n Waveform 2 2.5 3.0 ns AC WAVEFORMS For all waveforms, VM = 1.5V. VM VM VM 1/fMAX tPHL tw (L) Qna, Qnb tw (H) VM CP n tPLH SF00709 Waveform 1. Propagation Delay, Clock Input to Output, Clock Pulse Width, and Maximum Clock Frequency VM VM VM trec tPHL MR CP n Qna, Qnb VM tw (H) SF00708 Waveform 2. Master Reset Pulse Width, Master Reset to Output Delay, and Master Reset to Clock Recovery Time TEST CIRCUIT AND WAVEFORMS tw 90% VM 10% 90% VM 10% 90% VM 10% 90% VM 10% NEGATIVE PULSE POSITIVE PULSE tw AMP (V) tTHL (tf ) INPUT PULSE REQUIREMENTS rep. rate tw tTLH tTHL 1MHz 500ns 2.5ns 2.5ns Input Pulse Definition VCC family 74F D.U.T.PULSE GENERATOR R LC LR T VIN VOUT Test Circuit for Totem-Pole Outputs DEFINITIONS: R L = Load resistor; see AC ELECTRICAL CHARACTERISTICS for value. C L = Load capacitance includes jig and probe capacitance; see AC ELECTRICAL CHARACTERISTICS for value. R T = Termination resistance should be equal to ZOUT of pulse generators. tTHL (tf ) tTLH (tr ) tTLH (tr ) AMP (V) amplitude 3.0V 1.5V VM SF00006

Philips Semiconductors Product specification 74F393Dual 4-bit binary ripple counter

1988 Nov 01 6

DIP14: plastic dual in-line package; 14 leads (300 mil) SOT27-1

Philips Semiconductors Product specification 74F393Dual 4-bit binary ripple counter

1988 Nov 01 7

SO14: plastic small outline package; 14 leads; body width 3.9 mm SOT108-1

Philips Semiconductors Product specification 74F393Dual 4-bit binary ripple counter yyyy mmm dd 8 Definitions Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Disclaimers Life support — These products are not designed for use in life support appliances, devices or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes — Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Philips Semiconductors

811 East Arques Avenue

P.O. Box 3409 Sunnyvale, California 94088–3409 Telephone 800-234-7381  Copyright Philips Electronics North America Corporation 1998 All rights reserved. Printed in U.S.A. print code Date of release: 10-98 Document order number: 9397-750-05125 /C0109 /C0110 /C0114 Data sheet status Objective specification Preliminary specification Product specification Product status Development Qualification Production Definition [1] This data sheet contains the design target or goal specifications for product development. Specification may change in any manner without notice. This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips Semiconductors reserves the right to make chages at any time without notice in order to improve design and supply the best possible product. This data sheet contains final specifications. Philips Semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. Data sheet status [1] Please consult the most recently issued datasheet before initiating or completing a design.