74F3893 PHILIPS

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 10

Technical content

/C0109 /C0110 /C0114 74F3893 Quad futurebus backplane transceiver Product specification IC15 Data Handbook

1991 Jan 18

Philips Semiconductors Product specification 74F3893Quad Futurebus backplane transceiver 2January 18, 1991 853-1397 01496

FEATURES

  • Quad backplane transceiver
  • Drives heavily loaded backplanes with equivalent load impedances down to 10 ohms
  • Futurebus drivers sink 100mA
  • Reduced voltage swing (1 volt) produces less noise and reduces power consumption
  • High speed operation enhances performance of backplane buses and facilitates incident wave switching
  • Compatible with IEEE 896 and IEEE 1194.1 Futurebus Standards
  • Built–in precision band–gap (BG) reference provides accurate receiver thresholds and improved noise immunity
  • Glitch–free power up/power down operation on all outputs
  • Pin and function compatible with NSC DS3893

DESCRIPTION

The 74F3893 is a quad backplane transceivers and is intended to be used in very high speed bus systems. The 74F3893 interfaces to ‘Backplane Transceiver Logic’ (BTL). BTL features a reduced (1V to 2V) voltage swing for lower power consumption and a series diode on the drivers to reduce capacitive loading (< 5pF). Incident wave switching is employed, therefore BTL propagation delays are short. Although the voltage swing is much less for BTL, so is its receiver threshold region, therefore noise margins are excellent. BTL offers low power consumption, low ground bounce, EMI and crosstalk, low capacitive loading, superior noise margin and low propagation delays. This results in a high bandwidth, reliable backplane. The 74F3893 has four TTL outputs (Rn) on the receiver side with a common receiver enable input (RE). It has four data inputs (Dn) which are also TTL. These data inputs are NANDed with the data enable input (DE). The four I/O pins (bus side) are futurebus compatible, sink a minimum of 100mA, and are designed to drive heavily loaded backplanes with load impedances as low as 10 ohms. All outputs are designed to be glitch–free during power up and down. TYPE TYPICAL PROPAGATION DELAY TYPICAL SUPPLY CURRENT( TOTAL) 74F3893 3.0ns 55mA

ORDERING INFORMATION

DESCRIPTION COMMERCIAL RANGE VCC = 5V ±10%, Tamb = 0°C to +70°C PKG DWG # 20-pin PLCC N74F3893A SOT380-1 INPUT AND OUTPUT LOADING AND FAN OUT TABLE PINS DESCRIPTION 74F (U.L.) HIGH/LOW LOAD VALUE HIGH/LOW D0 – D3 Data inputs 1.0/0.067 20µA/40µA DE Data enable input 1.0/0.33 20µA/200µA RE Receiver enable input 1.0/0.067 20µA/40µA I/O0 – I/O3 Bus inputs 5.0/0.033 100µA/20µA I/O0 – I/O3 Bus outputs OC/166.7 OC/100mA R0 – R7 Receiver outputs 150/40 3mA/24mA Notes to input and output loading and fan out table One (1.0) FAST unit load is defined as: 20µA in the high state and 0.6mA in the low state. OC= Open collector.

Philips Semiconductors Product specification 74F3893Quad Futurebus backplane transceiver January 18, 1991 3 PIN CONFIGURATION 321 2 0 1 9 148 131211109 PLCC LOGIC GND VCC BG GNDD0R0 REDER3D3 I/O0 I/O1 BUS GND I/O2 I/O3 BUS GND BUS GND SF00573 LOGIC SYMBOL DE RE 2 4 7 9 D0 D1 D2 D3 I/O0 I/O1 1/O2 I/O3 R0 R1 R2 R3 VCC = Pin 1, LOGIC GND = Pin 8 BUS GND = Pin 13, 16, 19 BG GND = Pin 20 18 17 15 14 3 5 8 10 SF00574 IEC/IEEE SYMBOL 21D EN1 EN2 SF00575 FUNCTION TABLE INPUTS INPUT/ OUT- PUT OUT- PUT OPERATING DE RE Dn I/On Rn MODE H L L H L Transmit to bus H L H L H H H Dn D n Z Receiver 3–state, L H X H Z transmit to bus L L X H L Receive, I/On = inputs L L X L H Notes to function table 1. H = High voltage level 2. L = Low voltage level 3. X = Don’t care 4. Z = High impedance ”off” state LOGIC DIAGRAM VCC = Pin 1 LOGIC GND = Pin 6 BUS GND = Pin 13, 16, 19 BG GND = Pin 20 I/O0 RE I/O3 SF00576 D1 4 DE I/O2 I/O117

Philips Semiconductors Product specification 74F3893Quad Futurebus backplane transceiver January 18, 1991 4 ABSOLUTE MAXIMUM RATINGS (Operation beyond the limit set forth in this table may impair the useful life of the device. Unless otherwise noted these limits are over the operating free air temperature range.) SYMBOL PARAMETER RATING UNIT VCC Supply voltage –1.5 to +6.5 V VIN Input voltage –1.5 to +6.5 V IIN Input current –30 to +5 mA VOUT Voltage applied to output in high output state –0.5 to 5.5 V IOUT Current applied to output in low output state 200 mA Tamb Operating free air temperature range 0 to +70 °C Tstg Storage temperature range –65 to +150 °C RECOMMENDED OPERATING CONDITIONS LIMITS SYMBOL PARAMETER MIN NOM MAX UNIT VCC Supply voltage 4.5 5.0 5.5 V VIH High–level input voltage Dn, DE, RE 2.0 V VIL Low–level input voltage 0.8 V IIk Input clamp current –18 mA VTH Bus input threshold I/On only 1.475 1.55 1.625 mA IOH High–level output current Rn only –3 mA IOL Low–level output current 100 mA Tamb Operating free air temperature range 0 +70 °C

Philips Semiconductors Product specification 74F3893Quad Futurebus backplane transceiver January 18, 1991 5 DC ELECTRICAL CHARACTERISTICS (Over recommended operating free-air temperature range unless otherwise noted.) SYMBOL PARAMETER TEST LIMITS UNIT CONDITIONS 1 MIN TYP 2 MAX IOH High–level output current I/On VCC = MAX, VIL = MAX, VIH = MIN, VOH = 1.5V 10 100 µA VOH High-level output voltage Rn VCC = MAX, VIL = 1.3V, RE = 0.8V, IOH = MAX 2.5 V VOHB High-level output bus voltageI/On VCC = MAX, Dn = DE = 0.8V, VT = 2.0V, R T = 10Ω , RE = 2.0V 2.5 V VOL Low-level output voltage Rn VCC = MIN, VIN = 1.8V, RE = 0.8V, IOL = 6mA 0.35 0.5 V VOLB Low-level output I/On Dn = DE = VIH, IOL = 100mA 0.75 1.0 1.2 V bus voltage Dn = DE = VIH, IOL = 80mA 0.75 1.0 1.1 V VOCB Driver output positive I/On VCC = MAX or 0V, I/On = 1mA 1.9 2.9 V clamp voltage Dn = DE = 0.8V, RE = 2.0V I/On = 10mA 2.3 3.2 V VIK Input clamp voltage VCC = MIN, II =IIK –0.73 -1.2 V II Input current at maximum input voltageVCC = MAX, VI = 7.0V, DE = RE = Dn = VCC 100 µA IIH High–level input current Dn, RE, DE VCC = MAX, DE = RE = Dn =5.5V 20 µA IIHB High–level I/O bus current (power off) I/On VCC = 0V, Dn = DE = 0.8V, I/On =1.2V, RE = 0V 100 µA IIL Low–level input current Dn, RE VCC = MAX, VI = 0.5V, DE = 4.5V –40 µA DE VCC = MAX, VI = 0.5V, Dn = 4.5V –200 µA IILB Low–level I/O bus current (power on) I/On VCC = MAX, Dn = DE = 0.8V, I/On =0.75V, RE = 0V –20 20 µA IOZH Off–state output current, high–level voltage applied Rn VCC = MAX, VI = 2.7V, RE = 2V 20 µA IOZL Off–state output current, low–level voltage applied VCC = MAX, VI = 0.5V, RE = 2V –20 µA IOS Short circuit output current3 Rn ’F8 VCC = MAX -60 -150 mA ICC Supply current4 (total) VCC = MAX, (RE = VIH or VIL) 55 80 mA Notes to DC electrical characteristics 1. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions for the applicable type. 2. All typical values are at VCC = 5V, Tamb = 25°C. 3. Not more than one output should be shorted at a time. For testing IOS , the use of high-speed test apparatus and/or sample-and-hold techniques are preferable in order to minimize internal heating and more accurately reflect operational values. Otherwise, prolonged shorting of a high output may raise the chip temperature well above normal and thereby cause invalid readings in other parameter tests. In any sequence of parameter tests, IOS tests should be performed last.

Philips Semiconductors Product specification 74F3893Quad Futurebus backplane transceiver January 18, 1991 6 AC ELECTRICAL CHARACTERISTICS FOR DRIVER AND DRIVER ENABLE LIMITS Tamb = +25°C Tamb = 0°C to +70°C SYMBOL PARAMETER TEST VCC = +5.0V VCC = +5.0V ± 10% UNIT CONDITION C D = 50pF, RT = 10Ω C D = 50pF, RT = 10Ω MIN TYP MAX MIN MAX tPLH tPHL Propagation delay Dn to I/On Waveform 1 1.0 1.5 2.0 3.0 5.0 5.5 1.0 1.5 5.5 6.0 ns tPLH tPHL Propagation delay DE to I/On Waveform 1 1.0 1.5 2.0 3.0 4.5 5.5 1.0 1.5 5.5 6.0 ns tTLH tTHL Dn to I/O transition time 10% to 90%, 90% to 10% Waveform 1 1.0 1.0 4.0 4.0 1.0 1.0 5.0 5.0 ns tsk(o) Skew between drivers in same package 1.0 ns AC ELECTRICAL CHARACTERISTICS FOR RECEIVER LIMITS Tamb = +25°C Tamb = 0°C to +70°C SYMBOL PARAMETER TEST VCC = +5.0V VCC = +5.0V ± 10% UNIT CONDITION C L = 50pF, RL = 1kΩ C L = 50pF, RL = 1kΩ MIN TYP MAX MIN MAX tPLH tPHL Propagation delay I/On to Rn Waveform 2 1.0 3.6 2.0 5.5 4.5 7.5 1.0 3.6 5.5 8.5 ns AC ELECTRICAL CHARACTERISTICS FOR RECEIVER ENABLE A PORT LIMITS Tamb = +25°C Tamb = 0°C to +70°C SYMBOL PARAMETER TEST VCC = +5.0V VCC = +5.0V ± 10% UNIT CONDITION C L = 50pF, RL = 500Ω C L = 50pF, RL = 500Ω MIN TYP MAX MIN MAX tPZH tPZL Output enable time to high or low level, RE to Rn Waveform 3, 4 1.5 2.5 3.0 4.0 5.5 7.0 1.5 2.0 6.0 7.5 ns tPHZ tPLZ Output disable time from high or low level, RE to Rn Waveform 3, 4 1.5 1.5 3.0 3.0 5.5 5.5 1.0 1.0 6.5 6.0 ns

Philips Semiconductors Product specification 74F3893Quad Futurebus backplane transceiver January 18, 1991 7 AC WAVEFORMS VMVM VMVM I/On DE, Dn tPHL tPLH 90% 10% 90% 10% tTLHtTHL SF00577 Waveform 1. Propagation delay for driver VMVM VMVM Rn I/On tPHL tPLH SF00578 Waveform 2. Propagation delay for receiver VM VM VM tPHZtPZH VOH -0.3V RE Rn SF00579 Waveform 3. 3–state output enable time to high level and output disable time from high level VM VM VM tPLZtPZL VOL +0.3V RE Rn SF00580 Waveform 4. 3-state output enable time to low level and output disable time from low level Notes to AC waveforms 1. For all waveforms, VM = 1.5V. 2. The shaded areas indicate when the input is permitted to change for predictable output performance. TEST CIRCUITS AND WAVEFORMS tw 90% VM 10% 90% VM 10% 90% VM 10% 90% VM 10% NEGATIVE PULSE POSITIVE PULSE tw AMP (V) Low V Low V tTHL (tf ) INPUT PULSE REQUIREMENTS rep. rate tw tTLH tTHL 1MHz 500ns 2.5ns 2.5ns Input pulse definition VCC family D port D.U.T.PULSE GENERATOR R LC LR T VIN VOUT Test circuit for 3–state outputs on D port DEFINITIONS: R L = Load resistor; see AC electrical characteristics for value. C L = Load capacitance includes jig and probe capacitance; see AC electrical characteristics for value. R U = Pull up resistor; see AC Electrical Characteristics for value. C D = Load capacitance includes jig and probe capacitance; see AC electrical characteristics for value. R T = Termination resistance should be equal to ZOUT of pulse generators. tTHL (tf ) tTLH (tr ) tTLH (tr ) AMP (V) amplitude 3.0V 1.5V VM R L 7.0V VCC D.U.T.PULSE GENERATOR C DR T VIN VOUT Test circuit for outputs on I/O port R T 7.0V 1MHz 500nsI/O port 2.0V 1.5V 4.0ns 4.0ns Low V 0.0V 1.0V SWITCH POSITION TEST SWITCH closed openAll other tPLZ , tPZL SF00581

Philips Semiconductors Product specification 74F3893Quad futurebus backplane transceiver

1991 Jan 18 8

PLCC20: plastic leaded chip carrier; 20 leads SOT380-1

Philips Semiconductors Product specification 74F3893Quad futurebus backplane transceiver

1991 Jan 18 9

Philips Semiconductors Product specification 74F3893Quad futurebus backplane transceiver yyyy mmm dd 10 Definitions Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Disclaimers Life support — These products are not designed for use in life support appliances, devices or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes — Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Philips Semiconductors

811 East Arques Avenue

P.O. Box 3409 Sunnyvale, California 94088–3409 Telephone 800-234-7381  Copyright Philips Electronics North America Corporation 1998 All rights reserved. Printed in U.S.A. print code Date of release: 10-98 Document order number: 9397-750-05206 /C0109 /C0110 /C0114 Data sheet status Objective specification Preliminary specification Product specification Product status Development Qualification Production Definition [1] This data sheet contains the design target or goal specifications for product development. Specification may change in any manner without notice. This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips Semiconductors reserves the right to make chages at any time without notice in order to improve design and supply the best possible product. This data sheet contains final specifications. Philips Semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. Data sheet status [1] Please consult the most recently issued datasheet before initiating or completing a design.