74F3038 PHILIPS

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 8

Technical content

/C0109 /C0110 /C0114 74F3038 Quad 2-input NAND 30 Ω line driver (open collector) Product specification Supersedes data of 1990 Jan 29 IC15 Data Handbook

1998 May 21

Philips Semiconductors Product specification 74F3038Quad 2-input NAND 30Ω line driver (open collector)

21998 May 21 853-0022 19433

FEATURES

  • 30Ω line driver
  • 160mA output drive capability
  • High speed
  • Facilitates incident wave switching
  • 3nh lead inductance each on VCC and GND when both side pins are used

DESCRIPTION

The 74F3038 is a high current Open-Collector Line Driver composed of four 2-input NAND gates. It has been designed to deal with the transmission line effects of PC boards which appear when fast edge rates are used. The 74F3038 can sink 160mA with a V CC as low as 4.5V. This guarantees incident wave switching with VOL not more than 0.8V while driving impedances as low as 30Ω . This is applicable with any combination of outputs using continuous duty. The AC specifications for the 74F3038 were determined using the standard FAST load for open-collector parts of 50pF capacitance, a 500Ω pull-up resistor and a 500Ω pull-down resistor. (See Test Circuit). Reducing the load resistors to 100Ω will decrease the tPLH propagation delay by approximately 50% while increasing tPHL only slightly. The graph of typical propagation delay versus load resistor (see AC Characteristics section for Graph) shows a spline fit curve from four measured data points, R L = 30Ω , RL = 100Ω , RL = 300Ω , and RL = 500Ω . PIN CONFIGURATION 107 SF00570 D0a D0b Q 0 GND GND Q 1 D1a D1b Q 2 D2b D2a VCC VCC D3a D3b Q 3 TYPE TYPICAL PROPAGATION DELAY TYPICAL SUPPLY CURRENT (TOTAL) 74F3038 6.0ns 17mA

ORDERING INFORMATION

VCC = 5V ±10%, Tamb = 0°C to +70°C PACKAGE DRAWING NUMBER 16-pin Plastic DIP N74F3038N SOT38-4 16-pin Plastic SOL N74F3038D SOT162-1 INPUT AND OUTPUT LOADING AND FAN-OUT TABLE PINS DESCRIPTION 74F(U.L.) HIGH/LOW LOAD VALUE HIGH/LOW Dna, Dnb Data inputs 1.0/1.0 20µA/0.6mA Q n Data outputs OC/266 OC/160mA NOTE: One (1.0) FAST unit load is defined as: 20µA in the High state and 0.6mA in the Low state. OC = Open Collector. LOGIC SYMBOL D0a D0b D1a D2a D2b D3a D3bD1a Q0 Q1 Q2 Q3 36 9 1 6 1 2 7 8 10 11 14 15 VCC = Pin 12,13 GND = Pin 4, 5 SF00571 IEC/IEEE SYMBOL SF00572

Philips Semiconductors Product specification 74F3038Quad 2-input NAND 30Ω line driver (open collector)

1998 May 21 3

VCC = Pin 12,13 GND = Pin 4, 5 SF00569 FUNCTION TABLE INPUTS OUTPUT Dna Dnb Q n L L H L H H H L H H H L H = High voltage level L = Low voltage level ABSOLUTE MAXIMUM RATINGS (Operation beyond the limits set forth in this table may impair the useful life of the device. Unless otherwise noted these limits are over the operating free-air temperature range.) SYMBOL PARAMETER RATING UNIT VCC Supply voltage –0.5 to +7.0 V VIN Input voltage –0.5 to +7.0 V IIN Input current –30 to +5 mA VOUT Voltage applied to output in High output state –0.5 to VCC V IOUT Current applied to output in Low output state 320 mA Tamb Operating free-air temperature range 0 to +70 °C Tstg Storage temperature range –65 to +150 °C RECOMMENDED OPERATING CONDITIONS SYMBOL PARAMETER LIMITS UNITSYMBOL PARAMETER MIN NOM MAX UNIT VCC Supply voltage 4.5 5.0 5.5 V VIH High-level input voltage 2.0 V VIL Low-level input voltage 0.8 V IIK Input clamp current –18 mA VOH High-level output voltage 4.5 V IOL Low-level output current 160 mA Tamb Operating free-air temperature range 0 +70 °C

Philips Semiconductors Product specification 74F3038Quad 2-input NAND 30Ω line driver (open collector)

1998 May 21 4

DC ELECTRICAL CHARACTERISTICS (Over recommended operating free-air temperature range unless otherwise noted.) SYMBOL PARAMETER TEST CONDITIONS 1 LIMITS UNITSYMBOL PARAMETER TEST CONDITIONS 1 MIN TYP 2 MAX UNIT IOH High-level output current VCC = MIN, VIL = MAX, VIH = MIN, VOH = MAX 250 µA VO Low level output current VCC = MIN VIL= MAX IOL = 100mA ±10% V CC 0.42 0.55 V VOL Low-level output current VIL = MAX VIH = MIN IOL = 160mA3 ±5% V CC 0.80 V VIK Input clamp voltage VCC = MIN, II = IIK –0.73 –1.2 V II Input current at maximum input voltage VCC = MAX, VI = 7.0V 100 µA IIH High-level input current VCC = MAX, VI = 2.7V 20 µA IIL Low-level input current VCC = MAX, VI = 0.5V –0.6 mA ICC Supply current (total) ICCH VCC = MAX VIN = GND 3.5 6.0 mA ICC Supply current (total) ICCL VCC = MAX VIN = 4.5V 30 40 mA NOTES: 1. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions for the applicable type. 2. All typical values are at VCC = 5V, Tamb = 25°C. 3. IOL1 is the current necessary to guarantee the High to Low transition in a 30Ω transmission line on the incident wave. AC ELECTRICAL CHARACTERISTICS LIMITS SYMBOL PARAMETER TEST CONDITION Tamb = +25°C VCC = +5.0V C L = 50pF, RL = 500Ω Tamb = 0°C to +70°C VCC = +5.0V ± 10% C L = 50pF, RL = 500Ω UNIT MIN TYP MAX MIN MAX tPLH tPHL Propagation delay Dna, Dnb to Qn Waveform 1 6.0 1.0 8.5 2.0 11.5 5.0 6.0 1.0 12.0 5.0 ns AC WAVEFORMS For all waveforms, VM = 1.5V. VMVM VMVM Q n Dna, Dnb tPHL tPLH SF00005 Waveform 1. Propagation Delay for Inputs to Output

Philips Semiconductors Product specification 74F3038Quad 2-input NAND 30Ω line driver (open collector)

1998 May 21 5

TYPICAL PROPAGATION DELAYS VERSUS LOAD FOR OPEN COLLECTOR OUTPUTS NOTE: When using Open-Collector parts, the value of the pull-up resistor greatly affects the value of the tPLH . For example, changing the specified pull-up resistor value from 500Ω to 100Ω will improve the tPLH up to 50% with only a slight increase in the tPHL . However, if the value of the pull-up resistor is changed, the user must make certain that the total IOL current through the resistor and the total IILs of the receivers does not exceed the IOL maximum specification. tPLH tPHL 6005004003002001000 LOAD RESISTOR ( Ω ) PROPAGATION DELAY (ns) SF01361 TEST CIRCUIT AND WAVEFORMS tw 90% VM 10% 90% VM 10% 90% VM 10% 90% VM 10% NEGATIVE PULSE POSITIVE PULSE tw AMP (V) tTHL (tf ) INPUT PULSE REQUIREMENTS rep. rate tw tTLH tTHL 1MHz 500ns 2.5ns 2.5ns Input Pulse Definition VCC family 74F D.U.T.PULSE GENERATOR R LC LR T VIN VOUT Test Circuit for Open Collector Outputs DEFINITIONS: R L = Load resistor; see AC electrical characteristics for value. C L = Load capacitance includes jig and probe capacitance; see AC electrical characteristics for value. R T = Termination resistance should be equal to ZOUT of pulse generators. tTHL (tf ) tTLH (tr ) tTLH (tr ) AMP (V) amplitude 3.0V 1.5V VM R L 7.0V SF00027

Philips Semiconductors Product specification 74F3038Quad 2-input NAND 30 Ω line driver (open collector)

1998 May 21 6

DIP16: plastic dual in-line package; 16 leads (300 mil) SOT38-4

Philips Semiconductors Product specification 74F3038Quad 2-input NAND 30 Ω line driver (open collector)

1998 May 21 7

SO16: plastic small outline package; 16 leads; body width 7.5 mm SOT162-1

Philips Semiconductors Product specification 74F3038Quad 2-input NAND 30 Ω line driver (open collector)

1998 May 21 8

Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Disclaimers Life support — These products are not designed for use in life support appliances, devices or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes — Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Philips Semiconductors

811 East Arques Avenue

P.O. Box 3409 Sunnyvale, California 94088–3409 Telephone 800-234-7381  Copyright Philips Electronics North America Corporation 1998 All rights reserved. Printed in U.S.A. print code Date of release: 05-96 Document order number: 9397-750-05204 /C0109 /C0110 /C0114 Data sheet status Objective specification Preliminary specification Product specification Product status Development Qualification Production Definition [1] This data sheet contains the design target or goal specifications for product development. Specification may change in any manner without notice. This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips Semiconductors reserves the right to make chages at any time without notice in order to improve design and supply the best possible product. This data sheet contains final specifications. Philips Semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. Data sheet status [1] Please consult the most recently issued datasheet before initiating or completing a design.