74F3037 PHILIPS
Document overview
- Manufacturer or author: Provided By digicamel.com
- PDF pages: 8
Technical content
/C0109 /C0110 /C0114 74F3037 Quad 2-input NAND 30Ω driver Product specification IC15 Data Handbook
1990 Feb 09
Philips Semiconductors Product specification 74F3037Quad 2-input NAND 30Ω driver 2February 9, 1990 853 0021 98744
FEATURES
- 30Ω line driver
- 67mA output drive capability in the high state
- High speed
- Facilitates incident wave switching
- 3nh lead inductance each on VCC and GND when both side pins are used
- 160mA output drive capability in the low state
- Industrial temperature range available (–40°C to +85°C)
DESCRIPTION
The 74F3037 is a high current line driver composed of four 2–input NAND gates. It has been designed to deal with the transmission line effects of PC boards which appear when fast edge rates are used. The drive capability of the 74F3037 is 67mA source and 160mA sink with a VCC as low as 4.5V. This guarantees incident wave switching with VOH not less than 2.0V and VOL not more than 0.8mA while driving impedances as low as 30 ohms. This is applicable with any combination of outputs using continuous duty. The propagation delay of the part is minimally affected by reflections when terminated only by the TTL inputs of other devices. Performances may be improved by full or partial line termination. TYPE TYPICAL PROPAGATION DELAY TYPICAL SUPPLY CURRENT( TOTAL) 74F3037 2.0ns 16mA
ORDERING INFORMATION
COMMERCIAL RANGE INDUSTRIAL RANGE DESCRIPTION VCC = 5V ±10%, VCC = 5V ±10%, PKG DWG # Tamb = 0°C to +70°C Tamb = –40°C to +85°C 16–pin plastic DIP N74F3037N I74F3037N SOT38-4 16–pin plastic SOL N74F3037D I74F3037D SOT162-1 INPUT AND OUTPUT LOADING AND FAN OUT TABLE PINS DESCRIPTION 74F (U.L.) HIGH/LOW LOAD VALUE HIGH/LOW Dna, Dnb Data inputs 1.0/1.0 20µA/0.6mA Q n Data output 3350/266 67mA/160mA Note to input and output loading and fan out table One (1.0) FAST unit load is defined as: 20µA in the high state and 0.6mA in the low state. LOGIC DIAGRAM D0a D0b D1a D1b D2a D2b D3a D3b VCC = Pin 12,13 GND = Pin 4, 5 SF00569 FUNCTION TABLE INPUTS OUTPUT Dna Dnb Q n L L H L H H H L H H H L Notes to function table H = High voltage level L = Low voltage level
Philips Semiconductors Product specification 74F3037Quad 2-input NAND 30Ω driver February 9, 1990 3 PIN CONFIGURATION 107 SF00570 D0a D0b Q 0 GND GND Q 1 D1a D1b Q 2 D2b D2a VCC VCC D3a D3b Q 3 LOGIC SYMBOL D0a D0b D1a D2a D2b D3a D3bD1a Q0 Q1 Q2 Q3 36 9 1 6 1 2 7 8 10 11 14 15 VCC = Pin 12,13 GND = Pin 4, 5 SF00571 IEC/IEEE SYMBOL SF00572 ABSOLUTE MAXIMUM RATINGS (Operation beyond the limit set forth in this table may impair the useful life of the device. Unless otherwise noted these limits are over the operating free air temperature range.) SYMBOL PARAMETER RATING UNIT VCC Supply voltage –0.5 to +7.0 V VIN Input voltage –0.5 to +7.0 V IIN Input current –30 to +5 mA VOUT Voltage applied to output in high output state –0.5 to VCC V IOUT Current applied to output in low output state 320 mA Tamb Operating free air temperature range Commercial range 0 to +70 °C Industrial range –40 to +85 °C Tstg Storage temperature range –65 to +150 °C
Philips Semiconductors Product specification 74F3037Quad 2-input NAND 30Ω driver February 9, 1990 4 RECOMMENDED OPERATING CONDITIONS SYMBOL PARAMETER LIMITS TA = –40 to +85°CUNIT MIN NOM MAX VCC Supply voltage 4.5 5.0 5.5 V VIH High–level input voltage 2.4 V VIL Low–level input voltage 0.8 V IIk Input clamp current –18 mA IOH High–level output current –67 mA IOL Low–level output current 160 mA Tamb Operating free air temperature range Commercial range 0 +70 °C Industrial range –40 +85 °C DC ELECTRICAL CHARACTERISTICS (Over recommended operating free-air temperature range unless otherwise noted.) SYMBOL PARAMETER TEST LIMITS UNIT CONDITIONS 1 MIN TYP 2 MAX VCC = MIN, IOH = –45mA ±10%V CC 2.5 V VOH High–level output voltage VIL = MAX, ±5%V CC 2.7 V VIH = MIN IOH1 = –67mA 3 ±10%V CC 2.0 V VOL Low–level output voltage VCC = MIN, VIL = MAX, IOL = 100mA ±10%V CC 0.30 0.50 V VIH = MIN IOL1 = 160mA 4 ±5%V CC 0.30 0.50 V VIK Input clamp voltage VCC = MIN, II = IIK -0.73 -1.2 V II Input current at maximum input voltageVCC = MAX, VI = 7.0V 100 µA IIH High–level input current VCC = MAX, VI = 2.7V 20 µA IIL Low–level input current VCC = MAX, VI = 0.5V -0.6 mA IO Output current5 VCC = MAX, VO = 2.25V -100 -200 mA ICC Supply current (total) ICCH VCC = MAX 6.0 9.0 mA ICCL 30 40 mA Notes to DC electrical characteristics 1. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions for the applicable type. 2. All typical values are at VCC = 5V, Tamb = 25°C. 3. IOH1 is the current necessary to guarantee the low to high transition in a 30 ohm transmission line on the incident wave. 4. IOL1 is the current necessary to guarantee the high to low transition in a 30 ohm transmission line on the incident wave. 5. IO is tested under conditions that produce current approximately one half of the true short–circuit current (IOS ). AC ELECTRICAL CHARACTERISTICS LIMITS Tamb = +25°C Tamb = 0°C to +70°C Tamb =–40°C to +85°C SYMBOL PARAMETER TEST VCC = +5.0V VCC = +5.0V ± 10% VCC = +5.0V ± 10% UNIT CONDITION C L = 50pF, R L = 500Ω C L = 50pF, R L = 500Ω C L = 50pF, R L = 500Ω MIN TYP MAX MIN MAX MIN MAX tPLH tPHL Propagation delay Dna, Dnb to Qn Waveform 1 1.0 1.0 2.0 2.0 5.0 4.5 1.0 1.0 5.5 5.0 1.0 1.0 5.5 5.0 ns
Philips Semiconductors Product specification 74F3037Quad 2-input NAND 30Ω driver February 9, 1990 5 AC WAVEFORMS VMVM VMVM Q n Dna, Dnb tPHL tPLH SF00005 Waveform 1. Propagation delay for inverting outputs Note to AC waveforms For all waveforms, VM = 1.5V. TEST CIRCUIT AND WAVEFORMS tw 90% VM 10% 90% VM 10% 90% VM 10% 90% VM 10% NEGATIVE PULSE POSITIVE PULSE tw AMP (V) tTHL (tf ) INPUT PULSE REQUIREMENTS rep. rate tw tTLH tTHL 1MHz 500ns 2.5ns 2.5ns Input Pulse Definition VCC family 74F D.U.T.PULSE GENERATOR R LC LR T VIN VOUT Test Circuit for Totem-Pole Outputs DEFINITIONS: R L = Load resistor; see AC ELECTRICAL CHARACTERISTICS for value. C L = Load capacitance includes jig and probe capacitance; see AC ELECTRICAL CHARACTERISTICS for value. R T = Termination resistance should be equal to ZOUT of pulse generators. tTHL (tf ) tTLH (tr ) tTLH (tr ) AMP (V) amplitude 3.0V 1.5V VM SF00006
Philips Semiconductors Product specification 74F3037Quad 2-input NAND 30Ω driver
1990 Feb 09 6
DIP16: plastic dual in-line package; 16 leads (300 mil) SOT38-4
Philips Semiconductors Product specification 74F3037Quad 2-input NAND 30Ω driver
1990 Feb 09 7
SO16: plastic small outline package; 16 leads; body width 7.5 mm SOT162-1
Philips Semiconductors Product specification 74F3037Quad 2-input NAND 30Ω driver yyyy mmm dd 8 Definitions Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Disclaimers Life support — These products are not designed for use in life support appliances, devices or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes — Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Philips Semiconductors
811 East Arques Avenue
P.O. Box 3409 Sunnyvale, California 94088–3409 Telephone 800-234-7381 Copyright Philips Electronics North America Corporation 1998 All rights reserved. Printed in U.S.A. print code Date of release: 10-98 Document order number: 9397-750-05203 /C0109 /C0110 /C0114 Data sheet status Objective specification Preliminary specification Product specification Product status Development Qualification Production Definition [1] This data sheet contains the design target or goal specifications for product development. Specification may change in any manner without notice. This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips Semiconductors reserves the right to make chages at any time without notice in order to improve design and supply the best possible product. This data sheet contains final specifications. Philips Semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. Data sheet status [1] Please consult the most recently issued datasheet before initiating or completing a design.