74F273A PHILIPS

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 10

Technical content

/C0109 /C0110 /C0114 74F273A Octal D flip-flop Product specification IC15 Data Handbook

1996 Mar 12

Philips Semiconductors Product specification 74F273AOctal D flip–flop

21996 Mar 12 853–0066 16555

FEATURES

  • High impedance inputs for reduced loading (20µA in Low and High states)
  • Ideal buffer for MOS microprocessor or memory
  • Eight edge–triggered D–type flip–flops
  • Buffered common clock
  • Buffered asynchronous Master Reset
  • See 74F377A for clock enable version
  • See 74F373 for transparent latch version
  • See 74F374 for 3–State version

DESCRIPTION

The 74F273 has eight edge–triggered D–type flip–flops with individual D inputs and Q outputs. The common buffered Clock (CP) and Master Reset (MR) inputs load and reset (clear) all flip–flops simultaneously. The register is fully edge–triggered. The state of each D input, one setup time before the Low–to–High clock transition, is transferred to the corresponding flip–flop’s Q output. All outputs will be forced Low independently of Clock or Data inputs by a Low voltage level on the MR input. The device is useful for applications where the true output only is required and the CP and MR are common to all elements. TYPE TYPICAL fMAX TYPICAL SUPPLY CURRENT (TOTAL) 74F273A 170MHz 25mA

ORDERING INFORMATION

VCC = 5V±10%; Tamb = 0°C to +70°C PKG. DWG. # 20–pin plastic DIP 74F273AN SOT146-1 20–pin plastic SOL 74F273AD SOT163-1 INPUT AND OUTPUT LOADING AND FAN-OUT TABLE PINS DESCRIPTION 74F(U.L.) HIGH/LOW LOAD VALUE HIGH/LOW D0 – D7 Data inputs 1.0/0.033 20µA/20µA MR Master Reset input (active–Low) 1.0/0.033 20µA/20µA CP Clock pulse input (active rising edge) 1.0/0.033 20µA/20µA Q0 – Q7 Data outputs 50/33 1.0mA/20mA PIN CONFIGURATION 10 11 20MR Q3 Q4 GND VCC CP SF00346 LOGIC SYMBOL 3 4 7 8 13 14 18 17 D0 D1 D2 D3 D4 D5 D6 D7 Q0 Q1 Q2 Q3 Q4 Q5 Q6 Q7 2 5 6 9 12 15 16 19 MR CP VCC = Pin 20 GND = Pin 10 SF00347

Philips Semiconductors Product specification 74F273AOctal D flip–flop

1996 Mar 12 3

LOGIC SYMBOL (IEEE/IEC) SF00348 4 5 7 6 8 9 R 13 12 14 15 17 16 18 19 LOGIC DIAGRAM CP Q R D D CP Q R D D CP Q R D D CP Q R D D CP Q R D D CP Q R D D CP Q R D D CP Q R D D CP MR VCC = Pin 20 GND = Pin 10 SF00349 FUNCTION TABLE INPUTS OUTPUTS OPERATING MR CP Dn Q0 – Q7 MODE L X X L Reset (clear) H ↑ h H Load ”1” H ↑ l L Load ”0” H = High voltage level h = High voltage level one set–up time prior to the Low–to–High clock transition L = Low voltage level l = Low voltage level one set–up time prior to the Low–to–High clock transition X = Don’t care ↑ = Low–to–High clock transition

Philips Semiconductors Product specification 74F273AOctal D flip–flop

1996 Mar 12 4

(Operation beyond the limit set forth in this table may impair the useful life of the device. Unless otherwise noted these limits are over the operating free air temperature range.) SYMBOL PARAMETER RATING UNIT VCC Supply voltage –0.5 to +7.0 V VIN Input voltage –0.5 to +7.0 V IIN Input current –30 to +5 mA VOUT Voltage applied to output in High output state –0.5 to VCC V IOUT Current applied to output in Low output state 40 mA Tamb Operating free air temperature range 0 to +70 °C Tstg Storage temperature range –65 to +150 °C RECOMMENDED OPERATING CONDITIONS SYMBOL PARAMETER LIMITS UNIT MIN TYP MAX VCC Supply voltage 4.5 5.0 5.5 V VIH High–level input voltage 2.0 V VIL Low–level input voltage 0.8 V IIk Input clamp current –18 mA IOH High–level output current –1 mA IOL Low–level output current 20 mA Tamb Operating free air temperature range 0 +70 °C

Philips Semiconductors Product specification 74F273AOctal D flip–flop

1996 Mar 12 5

DC ELECTRICAL CHARACTERISTICS (Over recommended operating free-air temperature range unless otherwise noted.) SYMBOL PARAMETER TEST LIMITS UNIT CONDITIONS 1 MIN TYP 2 MAX MR & CP VCC = MIN, VIL = 0.0V3, ±10%V CC 2.5 V VOH High-level output voltage inputs VIH = 4.5V3, IOH = MAX ±5%V CC 2.7 3.4 V other VCC = MIN, VIL = MAX, ±10%V CC 2.5 V inputs VIH = MIN, IOH = MAX ±5%V CC 2.7 3.4 V VOL Low-level output voltage VCC = MIN, VIL = MAX, ±10%V CC 0.30 0.50 V VIH = MIN, IOH = MAX ±5%V CC 0.30 0.50 V VIK Input clamp voltage VCC = MIN, II = IIK –0.73 -1.2 V II Input current at maximum input voltage VCC = 0.0V, VI = 7.0V 100 µA IIH High–level input current VCC = MAX, VI = 2.7V 20 µA IIL Low–level input current VCC = MAX, VI = 0.5V –20 µA IOS Short–circuit output current4 VCC = MAX -60 -150 mA ICC Supply current (total) ICCH VCC = MAX 24 38 mA ICCL 27 43 mA NOTES: 1. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions for the applicable type. 2. All typical values are at VCC = 5V, Tamb = 25°C. 3. To reduce the effect of external noise during test. 4. Not more than one output should be shorted at a time. For testing IOS , the use of high-speed test apparatus and/or sample-and-hold techniques are preferable in order to minimize internal heating and more accurately reflect operational values. Otherwise, prolonged shorting of a high output may raise the chip temperature well above normal and thereby cause invalid readings in other parameter tests. In any sequence of parameter tests, IOS tests should be performed last. AC CHARACTERISTICS FOR ’F273A LIMITS SYMBOL PARAMETER WAVEFORM Tamb = +25°C VCC = +5.0V C L = 50pF R L = 500Ω Tamb = 0°C to +70°C VCC = +5.0V ±10% C L = 50pF R L = 500Ω UNIT Min Typ Max Min Max fMAX Maximum clock frequency 1 150 170 125 MHz tPLH tPHL Propagation delay CP to Qn 1 3.5 5.0 5.0 7.0 8.0 9.5 3.0 4.5 9.0 10.0 ns tPHL Propagation delay MR

Philips Semiconductors Product specification 74F273AOctal D flip–flop

1996 Mar 12 6

AC SETUP REQUIREMENTS FOR ’F273A LIMITS SYMBOL PARAMETER WAVEFORM Tamb = +25°C VCC = +5.0V C L = 50pF R L = 500Ω Tamb = 0°C to +70°C VCC = +5.0V ±10% C L = 50pF R L = 500Ω UNIT Min Typ Max Min Max ts(H) ts(L) Setup time, High or Low Dn to CP 3 3.0 2.0 2.5 2.5 th(H) th(L) Hold time, High or Low Dn to CP 3 0.5 0.0 2.5 1.0 ns tw (H) tw (L) Clock pulse width High or Low 1 4.5 3.5 5.0 4.0 ns tw (L) Master Reset pulse width, Low 2 3.0 3.5 ns tREC Recovery time MR to CP 2 4.0 5.0 ns AC WAVEFORMS CP VM VMVM tw (H) 1/fmax VMVM tPLHtw (L)tPHL Qn SF00294 Waveform 1. Propagation Delay, Clock Input to Output, Clock Pulse Width, and Maximum Clock Frequency VM SF00158 MR Qn VM tw (L) tPHL VM tREC CP VM Waveform 2. Master Reset Pulse Width, Master Reset to Output Delay and Master Reset to Clock Recovery Time th(H)ts(H) CP SF00191 VM VM VMVMVM VM th(L)ts(L) Dn Waveform 3. Data Setup and Hold Times NOTE: For all waveforms, VM = 1.5V. The shaded areas indicate when the input is permitted to change for predictable output performance.

Philips Semiconductors Product specification 74F273AOctal D flip–flop

1996 Mar 12 7

TEST CIRCUIT AND WAVEFORMS tw 90% VM 10% 90% VM 10% 90% VM 10% 90% VM 10% NEGATIVE PULSE POSITIVE PULSE tw AMP (V) tTHL (tf ) INPUT PULSE REQUIREMENTS rep. rate tw tTLH tTHL 1MHz 500ns 2.5ns 2.5ns Input Pulse Definition VCC family 74F D.U.T.PULSE GENERATOR R LC LR T VIN VOUT Test Circuit for Open Collector Outputs DEFINITIONS: R L = Load resistor; see AC electrical characteristics for value. C L = Load capacitance includes jig and probe capacitance; see AC electrical characteristics for value. R T = Termination resistance should be equal to ZOUT of pulse generators. tTHL (tf ) tTLH (tr ) tTLH (tr ) AMP (V) amplitude 3.0V 1.5V VM R L 7.0V SF00128 TEST SWITCH tPLZ closed tPZL closed All other open SWITCH POSITION

Philips Semiconductors Product specification 74F273AOctal D flip-flop

1996 Mar 12 8

DIP20: plastic dual in-line package; 20 leads (300 mil) SOT146-1

Philips Semiconductors Product specification 74F273AOctal D flip-flop

1996 Mar 12 9

SO20: plastic small outline package; 20 leads; body width 7.5 mm SOT163-1

Philips Semiconductors Product specification 74F273AOctal D flip-flop yyyy mmm dd 10 Definitions Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Disclaimers Life support — These products are not designed for use in life support appliances, devices or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes — Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Philips Semiconductors

811 East Arques Avenue

P.O. Box 3409 Sunnyvale, California 94088–3409 Telephone 800-234-7381  Copyright Philips Electronics North America Corporation 1998 All rights reserved. Printed in U.S.A. print code Date of release: 10-98 Document order number: 9397-750-05113 /C0109 /C0110 /C0114 Data sheet status Objective specification Preliminary specification Product specification Product status Development Qualification Production Definition [1] This data sheet contains the design target or goal specifications for product development. Specification may change in any manner without notice. This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips Semiconductors reserves the right to make chages at any time without notice in order to improve design and supply the best possible product. This data sheet contains final specifications. Philips Semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. Data sheet status [1] Please consult the most recently issued datasheet before initiating or completing a design.