74F269 PHILIPS
Document overview
- Manufacturer or author: Provided By digicamel.com
- PDF pages: 14
Technical content
/C0109 /C0110 /C0114 74F269 8-bit bidirectional binary counter Product specification 1996 Jan 05 INTEGRATED CIRCUITS IC15 Data Handbook
Philips Semiconductors Product specification 74F2698–bit bidirectional binary counter
21996 Jan 05 853–0056 16186
FEATURES
- Synchronous counting and loading
- Built-in look-ahead carry capability
- Count frequency 115MHz typ
- Supply current 95mA typ
DESCRIPTION
The 74F269 is a fully synchronous 8-stage Up/Down Counter featuring a preset capability for programmable operation, carry look-ahead for easy cascading and a U/D input to control the direction of counting. All state changes, whether in counting or parallel loading, are initiated by the rising edge of the clock. TYPE TYPICAL fMAX TYPICAL SUPPLY CURRENT (TOTAL) 74F269 115MHz 95mA PIN CONFIGURATION 1312 1U/D CEP CET TC PE VCC CP GND SF00834
ORDERING INFORMATION
DESCRIPTION COMMERCIAL RANGE VCC = 5V ±10%, Tamb = 0°C to +70°C PKG DWG # 24-Pin Plastic Slim DIP (300mil) N74F269N SOT222-1 24-Pin Plastic SOL N74F269D SOT137-1 24-Pin Plastic SSOP type II N74F269DB SOT340-1 INPUT AND OUTPUT LOADING AND FAN-OUT TABLE PINS DESCRIPTION 74F(U.L.) HIGH/LOW LOAD VALUE HIGH/LOW P0 - P7 Parallel Data inputs 1.0/1.0 20µA/0.6mA PE Parallel Enable input (active Low) 1.0/1.0 20µA/0.6mA U/D Up/Down count control input 1.0/1.0 20µA/0.6mA CEP Count Enable Parallel input (active Low) 1.0/1.0 20µA/0.6mA CET Count Enable Trickle input (active Low) 1.0/1.0 20µA/0.6mA CP Clock input 1.0/1.0 20µA/0.6mA TC Terminal Count output (active Low) 50/33 1.0mA/20mA Q0 - Q7 Flip-flop outputs 50/33 1.0mA/20mA NOTE: One (1.0) FAST Unit Load is defined as: 20µA in the High state and 0.6mA in the Low state.
1996 Jan 05 3
24 M1[LOAD]
Figure 1. Synchronous Multistage Counting Scheme Down is with all Qn outputs Low.
Philips Semiconductors Product specification 74F2698–bit bidirectional binary counter
1996 Jan 05 4
D QCP TOGGLE Q PE CP Pn U/D CEP DETAIL A VCC =Pin 19 GND=Pin 7 SF00837
Philips Semiconductors Product specification 74F2698–bit bidirectional binary counter
1996 Jan 05 5
(Operation beyond the limits set forth in this table may impair the useful life of the device. Unless otherwise noted these limits are over the operating free-air temperature range.) SYMBOL PARAMETER RATING UNIT VCC Supply voltage –0.5 to +7.0 V VIN Input voltage –0.5 to +7.0 V IIN Input current –30 to +5 mA VOUT Voltage applied to output in High output state –0.5 to VCC V IOUT Current applied to output in Low output state 40 mA Tamb Operating free-air temperature range 0 to +70 °C Tstg Storage temperature –65 to +150 °C RECOMMENDED OPERATING CONDITIONS SYMBOL PARAMETER LIMITS UNITSYMBOL PARAMETER MIN NOM MAX UNIT VCC Supply voltage 4.5 5.0 5.5 V VIH High-level input voltage 2.0 V VIL Low-level input voltage 0.8 V IIK Input clamp current –18 mA IOH High-level output current –1 mA IOL Low-level output current 20 mA Tamb Operating free-air temperature range 0 70 °C DC ELECTRICAL CHARACTERISTICS (Over recommended operating free-air temperature range unless otherwise noted.) NO TAG LIMITS SYMBOL PARAMETER TEST CONDITIONS NO TAG MIN TYP NO TAG MAX UNIT VO High level output voltage VCC = MIN, VIL = MAX ±10%V CC 2.5 VVOH High-level output voltage VIH = MIN, IOH = MAX ±5%V CC 2.7 3.4 V VO Low level output voltage VCC = MIN, VIL = MAX ±10%V CC 0.30 0.50 VVOL Low-level output voltage VIH = MIN, IOL = MAX ±5%V CC 0.30 0.50 V VIK Input clamp voltage VCC = MIN, II = IIK –0.73 –1.2 V II Input current at maximum input voltageVCC = MAX, VI = 7.0V 100 µA IIH High-level input current VCC = MAX, VI = 2.7V 20 µA IIL Low-level input current VCC = MAX, VI = 0.5V –0.6 mA IOS Short-circuit output currentNO TAG VCC = MAX –60 –150 mA ICC Supply current (total) ICCH VCC = PE =CET =CEP =U/D=GND, Pn=4.5V, CP=↑ 93 120 mA ICC Supply current (total) ICCL CC MAX PE =CET =CEP =U/D=GND, Pn=GND, CP= ↑ 98 125 mA NOTES: 1. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions for the applicable type. 2. All typical values are at VCC = 5V, Tamb = 25°C. 3. Not more than one output should be shorted at a time. For testing IOS , the use of high-speed test apparatus and/or sample-and-hold techniques are preferable in order to minimize internal heating and more accurately reflect operational values. Otherwise, prolonged shorting of a High output may raise the chip temperature well above normal and thereby cause invalid readings in other parameter tests. In any sequence of parameter tests, IOS tests should be performed last.
Philips Semiconductors Product specification 74F2698–bit bidirectional binary counter
1996 Jan 05 6
AC ELECTRICAL CHARACTERISTICS LIMITS SYMBOL PARAMETER TEST CONDITIONS Tamb = +25°C VCC = +5V C L = 50pF, RL = 500Ω Tamb = 0°C to +70°C VCC = +5V ± 10% C L = 50pF, RL = 500Ω UNIT MIN TYP MAX MIN MAX fMAX Maximum clock frequency Waveform 1 100 115 85 MHz tPLH tpPHL Propagation delay CP to Qn (Load, PE = Low) Waveform 1 3.0 4.0 6.0 6.5 8.5 8.5 3.0 4.0 9.0 9.0 ns ns tPLH tPHL Propagation delay CP to Q n (Count, PE = High) Waveform 1 3.0 4.5 6.0 7.0 9.0 10.0 3.0 4.0 10.0 10.5 ns ns tPLH tPHL Propagation delay CP to TC Waveform 1 4.5 5.0 6.5 6.5 9.5 9.5 4.0 5.0 10.5 10.0 ns ns tPLH tPHL Propagation delay CET to TC Waveform 2 3.5 3.0 6.0 6.5 9.0 9.0 3.0 3.0 10.0 10.0 ns ns tPLH tPHL Propagation delay U/D to TC Waveform 3 4.5 4.5 7.0 7.0 9.0 9.5 4.0 4.0 10.0 10.0 ns ns AC SETUP REQUIREMENTS LIMITS SYMBOL PARAMETER TEST CONDITIONS Tamb = +25°C VCC = +5V C L = 50pF, RL = 500Ω Tamb = 0°C to +70°C VCC = +5V ± 10% C L = 50pF, RL = 500Ω UNIT MIN TYP MIN MAX ts(H) ts(L) Setup time, High or Low P n to CP Waveform 4 3.5 3.5 2.5 2.5 ns ns th(H) th(L) Hold time, High or Low P n to CP Waveform 4 1.0 1.0 1.0 ns ns ts(H) ts(L) Setup time, High or Low PE to CP Waveform 4 5.5 6.5 5.5 6.5 ns ns th(H) th(L) Hold time, High or Low PE to CP Waveform 4 0 ns ns ts(H) ts(L) Setup time, High or Low CEP or CET to CP Waveform 5 6.0 8.0 5.0 6.5 ns ns th(H) th(L) Hold time, High or Low CEP or CET to CP Waveform 5 0 ns ns ts(H) ts(L) Setup time, High or Low U/D to CP Waveform 6 8.0 6.5 6.5 6.5 ns ns th(H) th(L) Hold time, High or Low U/D to CP Waveform 6 0 ns ns tw (H) tw (L) CP Pulse width High or Low Waveform 1 4.0 4.5 4.0 5.0 ns ns
Philips Semiconductors Product specification 74F2698–bit bidirectional binary counter
1996 Jan 05 7
253 254 255 0 1 2 2 1 0 255 254 253 COUNT UP COUNT DOWNINHIBITLOAD PE TC CEP AND CET U/D CP SEQUENCE SF00838B
Philips Semiconductors Product specification 74F2698–bit bidirectional binary counter
1996 Jan 05 8
For all waveforms, VM = 1.5V. The shaded areas indicate when the input is permitted to change for predictable output performance. tPHL VM tPHL VM VM VM 1/fMAX tW (L) CP Q n tW (H) VM VM tPLH tPLH VM TC SF00791A Waveform 1. Propagation Delay, Clock Input to Output, Clock Pulse Width, and Maximum Clock Frequency VM VM VM VM tPLHtPHL CET TC SF00792 Waveform 2. Propagation Delay, CET Input to Terminal Count Output VM VM VM tPLHtPHL VM U/D TC SF00793 Waveform 3. Propagation Delay, Up/Down Count Control Input to Terminal Count Output CP VM VM VM VM VM VM ts ts(L) ts(H)th = 0 t h = 0 Pn PE SF00844 VM VM th Waveform 4. Parallel Data and Parallel Enable Setup and Hold Times CP Q n VM VM VM VM th(L) t h(H) CET CEP ts(H)ts(L) COUNT NO CHANGE SF00842 VM VM Waveform 5. Count Enables Setup and Hold Times CP VMVM VM VM ts(H)th thts(L) COUNT UPCOUNT DOWN U/D Q n SF00839 VM VM Waveform 6. Up/Down Count Control Setup and Hold Times
Philips Semiconductors Product specification 74F2698–bit bidirectional binary counter
1996 Jan 05 9
TEST CIRCUIT AND WAVEFORMS tw 90% VM 10% 90% VM 10% 90% VM 10% 90% VM 10% NEGATIVE PULSE POSITIVE PULSE tw AMP (V) tTHL (tf ) INPUT PULSE REQUIREMENTS rep. rate tw tTLH tTHL 1MHz 500ns 2.5ns 2.5ns Input Pulse Definition VCC family 74F D.U.T.PULSE GENERATOR R LC LR T VIN VOUT Test Circuit for Totem-Pole Outputs DEFINITIONS: R L = Load resistor; see AC ELECTRICAL CHARACTERISTICS for value. C L = Load capacitance includes jig and probe capacitance; see AC ELECTRICAL CHARACTERISTICS for value. R T = Termination resistance should be equal to ZOUT of pulse generators. tTHL (tf ) tTLH (tr ) tTLH (tr ) AMP (V) amplitude 3.0V 1.5V VM SF00006
Philips Semiconductors Product specification 74F2698–bit bidirectional binary counter
1996 Jan 05 10
DIP24: plastic dual in-line package; 24 leads (300 mil) SOT222-1
Philips Semiconductors Product specification 74F2698–bit bidirectional binary counter
1996 Jan 05 11
SO24: plastic small outline package; 24 leads; body width 7.5 mm SOT137-1
Philips Semiconductors Product specification 74F2698–bit bidirectional binary counter
1996 Jan 05 12
SSOP24: plastic shrink small outline package; 24 leads; body width 5.3 mm SOT340-1
Philips Semiconductors Product specification 74F2698–bit bidirectional binary counter
1996 Jan 05 13
Philips Semiconductors Product specification 74F2698-bit bidirectional binary counter Philips Semiconductors and Philips Electronics North America Corporation reserve the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. LIFE SUPPORT APPLICATIONS Philips Semiconductors and Philips Electronics North America Corporation Products are not designed for use in life support appliances, devices, or systems where malfunction of a Philips Semiconductors and Philips Electronics North America Corporation Product can reasonably be expected to result in a personal injury. Philips Semiconductors and Philips Electronics North America Corporation customers using or selling Philips Semiconductors and Philips Electronics North America Corporation Products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors and Philips Electronics North America Corporation for any damages resulting from such improper use or sale. This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips Semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. Philips Semiconductors
811 East Arques Avenue
P.O. Box 3409 Sunnyvale, California 94088–3409 Telephone 800-234-7381 DEFINITIONS Data Sheet Identification Product Status Definition Objective Specification Preliminary Specification Product Specification Formative or in Design Preproduction Product Full Production This data sheet contains the design target or goal specifications for product development. Specifications may change in any manner without notice. This data sheet contains Final Specifications. Philips Semiconductors reserves the right to make changes at any time without notice, in order to improve design and supply the best possible product. Philips Semiconductors and Philips Electronics North America Corporation register eligible circuits under the Semiconductor Chip Protection Act. Copyright Philips Electronics North America Corporation 1996 All rights reserved. Printed in U.S.A. (print code) Date of release: July 1994 Document order number: 9397-750-05112