74F257A PHILIPS

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 10

Technical content

Quad 2-line to 1-line selector/multiplexer, non-inverting (3-State) Product specification 1995 Mar 31 INTEGRATED CIRCUITS IC15 Data Handbook

Philips Semiconductors Product specification 74F257AQuad 2-line to 1-line selector/multiplexer, non-inverting (3-State)

21995 Mar 31 853–0360 15059

FEATURES

  • Industrial range available (–40°C to +85°C)
  • Multifunction capability
  • Non-inverting data path
  • 3-State outputs
  • See 74F258A for inverting version

DESCRIPTION

The 74F257A has four identical 2-input multiplexers with 3-State outputs which select 4 bits of data from two sources uncer control of a common Select (S) input. The I0a inputs are selected when the common Select input is Low and the I1n inputs are selected when the common Select input is High. Data appears at the outputs in true non-inverted form from the selected inputs. The 74F257A is the logic implementation of a 4-pole, 2-position switch where the position of the switch is determined by the logic levels supplied to the common Slect input. Outputs are forced to a high impedance “off” state when the Output Enable (OE ) is High. All but one device must be in high impedance state to avoid currents that would exceed the maximum rating if the outputs were tied together. Design of the Output Enable signals must ensure that there is no overlap when outputs of 3-state devices were tied together. PIN CONFIGURATION 107 Yb VCC Yd I0c I1c I1d OE I0d S I0a I1b I1a Ya I0b 98GND Yc SF00673 TYPE TYPICAL PROPAGATION DELAY TYPICAL SUPPLY CURRENT (TOTAL) 74F257A 4.3ns 12mA

ORDERING INFORMATION

DRAWINGDESCRIPTION COMMERCIAL RANGE VCC = 5V ±10%, Tamb = 0°C to +70°C INDUSTRIAL RANGE VCC = 5V ±10%, Tamb = –40°C to +85°C DRAWING NUMBER 16-pin plastic DIP N74F257AN I74F257AN SOT38-4 16-pin plastic SO N74F257AD I74F257AD SOT109-1 INPUT AND OUTPUT LOADING AND FAN-OUT TABLE PINS DESCRIPTION 74F (U.L.) HIGH/LOW LOAD VALUE HIGH/LOW I0n, I1n Data inputs 1.0/1.0 20µA/0.6mA S Common Select input 1.0/1.0 20µA/0.6mA OE Output Enable input (active Low) 1.0/1.0 20µA/0.6mA Ya – Yd Data outputs 150/33 3.0mA/20mA NOTE: One (1.0) FAST unit load is defined as: 20µA in the High state and 0.6mA in the Low state. LOGIC SYMBOL VCC = Pin 16 GND = Pin 8 SF00674 S OE 2356 1 1 1 0 1 4 I0a I1a I0b I1b I0c I1c I0d Ya Yb Yc Yd 479 1 2 I1d LOGIC SYMBOL (IEEE/IEC) SF00675 2 1 15 EN 1 G1 MUX

Philips Semiconductors Product specification 74F257AQuad 2-line to 1-line selector/multiplexer, non-inverting (3-State)

1995 Mar 31 3

I0a I1a I0b I1b I0c I1c I0d I1dOE S 2 3 5 6 11 10 14 1315 1 479 1 2 Ya Yb Yc Yd VCC = Pin 16 GND = Pin 8 SF00676 FUNCTION TABLE INPUTS OUTPUT OE S I0 I1 Y H X X X Z L H X L L L H X H H L L L X L L L H X H H = High voltage level L = Low voltage level X = Don’t care Z = High impedance “off” state APPLICATION SF00677 I0a I1a I0b I1b I0c I1c I0d I1d Ya Yb Yc Yd I0a I1a I0b I1b I0c I1c I0d I1d Ya Yb Yc Yd I0a I1a I0b I1b I0c I1c I0d I1d Ya Yb Yc Yd I0a I1a I0b I1b I0c I1c I0d I1d Ya Yb Yc Yd 74F257A74F257A74F257A74F257A 4-BIT DATA BUS OE S OE S OE S OE S WORD A WORD B WORD C WORD D WORD E WORD F WORD G WORD H Y0 Y1 Y2 Y3 74F139 C B A ENABLE

Philips Semiconductors Product specification 74F257AQuad 2-line to 1-line selector/multiplexer, non-inverting (3-State)

1995 Mar 31 4

(Operation beyond the limits set forth in this table may impair the useful life of the device. Unless otherwise noted these limits are over the operating free-air temperature range.) SYMBOL PARAMETER RATING UNIT VCC Supply voltage –0.5 to +7.0 V VIN Input voltage –0.5 to +7.0 V IIN Input current –30 to +5 mA VOUT Voltage applied to output in High output state –0.5 to VCC V IOUT Current applied to output in Low output state 48 mA T O perating free air temperature range Commercial range 0 to +70 °C Tamb Operating free-air temperature range Industrial range –40 to +85 °C Tstg Storage temperature range –65 to +150 °C RECOMMENDED OPERATING CONDITIONS SYMBOL PARAMETER LIMITS UNITSYMBOL PARAMETER MIN NOM MAX UNIT VCC Supply voltage 4.5 5.0 5.5 V VIH High-level input voltage 2.0 V VIL Low-level input voltage 0.8 V IIK Input clamp current –18 mA IOH High-level output current –3 mA IOL Low-level output current 24 mA T O perating free air temperature range Commercial range 0 +70 °C Tamb Operating free-air temperature range Industrial range –40 +85 °C

Philips Semiconductors Product specification 74F257AQuad 2-line to 1-line selector/multiplexer, non-inverting (3-State)

1995 Mar 31 5

DC ELECTRICAL CHARACTERISTICS (Over recommended operating free-air temperature range unless otherwise noted.) SYMBOL PARAMETER TEST CONDITIONS 1 LIMITS UNITSYMBOL PARAMETER TEST CONDITIONS 1 MIN TYP 2 MAX UNIT VO High level output voltage VCC = MIN, VIL = MAX, ±10%V CC 2.4 V VOH High-level output voltage CC , IL , VIH = MIN, IOH = MAX ±5%V CC 2.7 3.3 V VO Low level output voltage VCC = MIN, VIL = MAX, ±10%V CC 0.35 0.50 V VOL Low-level output voltage CC , IL , VIH = MIN, IOL = MAX ±5%V CC 0.35 0.50 V VIK Input clamp voltage VCC = MIN, II = IIK –0.73 –1.2 V II Input current at maximum input voltageVCC = MAX, VI = 7.0V 100 µA IIH High-level input current VCC = MAX, VI = 2.7V 20 µA IIL Low-level input current VCC = MAX, VI = 0.5V –0.6 mA IOZH Off state output current, High-level voltage applied VCC = MAX, VO = 2.7V 50 µA IOZL Off state output current, Low-level voltage applied VCC = MAX, VO = 0.5V –50 µA IOS Short-circuit output current3 VCC = MAX -60 –150 mA ICCH 9.0 15.0 mA ICC Supply current4 (total) ICCL VCC = MAX 14.5 22.0 mA ICCZ 15.0 23.0 mA NOTES: 1. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions for the applicable type. 2. All typical values are at VCC = 5V, Tamb = 25°C. 3. Not more than one output should be shorted at a time. For testing IOS , the use of high-speed test apparatus and/or sample-and-hold techniques are preferable in order to minimize internal heating and more accurately reflect operational values. Otherwise, prolonged shorting of a High output may raise the chip temperature well above normal and thereby cause invalid readings in other parameter tests. In any sequence of parameter tests, IOS tests should be performed last. 4. Measure ICC with all outputs open and inputs grounded. AC ELECTRICAL CHARACTERISTICS LIMITS SYMBOL PARAMETER TEST CONDITION Tamb = +25°C VCC = +5.0V C L = 50pF R L = 500Ω Tamb = 0°C to +70°C VCC = +5.0V ± 10% C L = 50pF R L = 500Ω Tamb = –40°C to +85°C VCC = +5.0V ± 10% C L = 50pF R L = 500Ω UNIT MIN TYP MAX MIN MAX MIN MAX tPLH tPHL Propagation delay In to Yn Waveform 1 3.0 2.0 4.5 3.5 6.0 5.0 3.0 2.0 7.0 6.0 3.0 2.0 7.0 7.0 ns tPLH tPHL Propagation delay S to Yn Waveform 1 5.0 4.0 7.5 5.5 9.5 7.0 5.0 4.0 10.5 8.0 5.0 4.0 10.5 8.5 ns tPZH tPZL Output Enable time to High or Low level Waveform 2 Waveform 3 4.5 4.5 6.5 6.0 7.5 7.5 4.5 4.5 8.5 8.5 4.5 4.5 8.5 8.5 ns tPHZ tPLZ Output Disable time from High or Low level Waveform 2 Waveform 3 2.0 2.0 4.0 3.5 5.5 5.5 2.0 2.0 6.0 6.0 2.0 2.0 6.0 6.0 ns

Philips Semiconductors Product specification 74F257AQuad 2-line to 1-line selector/multiplexer, non-inverting (3-State)

1995 Mar 31 6

For all waveforms, VM = 1.5V. VMVM VMVM Yn In or S tPHL tPLH SF00679 Waveform 1. Propagation Delay, Data and Select to Output VOH –0.3V VM VMVM Yn tPZH tPHZ SF00213 OE Waveform 2. 3-State Output Enable Time to High Level and Output Disable Time from High Level VOL +0.3V VM VMVM Yn tPZL tPLZ SF00214 OE Waveform 3. 3-State Output Enable Time to Low Level and Output Disable Time from Low Level TEST CIRCUIT AND WAVEFORMS tw 90% VM 10% 90% VM 10% 90% VM 10% 90% VM 10% NEGATIVE PULSE POSITIVE PULSE tw AMP (V) tTHL (tf ) INPUT PULSE REQUIREMENTS rep. rate tw tTLH tTHL 1MHz 500ns 2.5ns 2.5ns Input Pulse Definition VCC family 74F D.U.T.PULSE GENERATOR R LC LR T VIN VOUT Test Circuit for 3-State Outputs DEFINITIONS: R L = Load resistor; see AC electrical characteristics for value. C L = Load capacitance includes jig and probe capacitance; see AC electrical characteristics for value. R T = Termination resistance should be equal to ZOUT of pulse generators. tTHL (tf ) tTLH (tr ) tTLH (tr ) AMP (V) amplitude 3.0V 1.5V VM R L 7.0V SF00777 TEST SWITCH tPLZ closed tPZL closed All other open SWITCH POSITION

Philips Semiconductors Product specification 74F257AQuad 2-line 1-line selector/multiplexer, non-inverting (3-State)

1995 Mar 31 7

DIP16: plastic dual in-line package; 16 leads (300 mil) SOT38-4

Philips Semiconductors Product specification 74F257AQuad 2-line 1-line selector/multiplexer, non-inverting (3-State)

1995 Mar 31 8

SO16: plastic small outline package; 16 leads; body width 3.9 mm SOT109-1

Philips Semiconductors Product specification 74F257AQuad 2-line 1-line selector/multiplexer, non-inverting (3-State)

1995 Mar 31 9

Philips Semiconductors Product specification 74F257AQuad 2-line 1-line selector/multiplexer, non-inverting (3-State) Philips Semiconductors and Philips Electronics North America Corporation reserve the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. LIFE SUPPORT APPLICATIONS Philips Semiconductors and Philips Electronics North America Corporation Products are not designed for use in life support appliances, devices, or systems where malfunction of a Philips Semiconductors and Philips Electronics North America Corporation Product can reasonably be expected to result in a personal injury. Philips Semiconductors and Philips Electronics North America Corporation customers using or selling Philips Semiconductors and Philips Electronics North America Corporation Products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors and Philips Electronics North America Corporation for any damages resulting from such improper use or sale. This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips Semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. Philips Semiconductors

811 East Arques Avenue

P.O. Box 3409 Sunnyvale, California 94088–3409 Telephone 800-234-7381 DEFINITIONS Data Sheet Identification Product Status Definition Objective Specification Preliminary Specification Product Specification Formative or in Design Preproduction Product Full Production This data sheet contains the design target or goal specifications for product development. Specifications may change in any manner without notice. This data sheet contains Final Specifications. Philips Semiconductors reserves the right to make changes at any time without notice, in order to improve design and supply the best possible product. Philips Semiconductors and Philips Electronics North America Corporation register eligible circuits under the Semiconductor Chip Protection Act.  Copyright Philips Electronics North America Corporation 1996 All rights reserved. Printed in U.S.A. (print code) Date of release: July 1994 Document order number: 9397-750-05107