74F175A PHILIPS
Document overview
- Manufacturer or author: Provided By digicamel.com
- PDF pages: 10
Technical content
/C0109 /C0110 /C0114 74F175*, 74F175A Quad D flip-flop Product specification IC15 Data Handbook
1996 Mar 12
- Discontinued part. Please see the Discontinued Product List in Section 1, page 21.
Philips Semiconductors Product specification 74F175AQuad D flip-flop
21996 Mar 12 853–0047 16555
FEATURES
- Four edge-triggered D-type flip-flops
- Buffered common clock
- Buffered asynchronous Master Reset
- True and complementary outputs
- Industrial temperature range available (–40°C to +85°C)
- PNP light loading inputs
DESCRIPTION
The 74F175A is a quad, edge-triggered D-type flip-flop with individual D inputs and both Q and Q outputs. The common buffered Clock (CP) and Master Reset (MR) inputs load and reset (clear) all flip-flops simultaneously. The register is fully edge-triggered. The state of each D input, one setup time before the Low-to-High clock transition is transferred to the corresponding flip-flop’s Q output. All Q outputs will be forced Low independently of clock or data inputs by a Low voltage level on the MR input. The device is useful for applications where both true and complementary outputs are required, and the CP and MR are common to all storage elements. PIN CONFIGURATION 107 VCC SF00718 Q 3 Q 2 CP MR Q 0 Q 1 GND TYPE TYPICAL fmax TYPICAL SUPPLY CURRENT (TOTAL) 74F175A 160MHz 22mA
ORDERING INFORMATION
DESCRIPTION COMMERCIAL RANGE VCC = 5V ±10%, Tamb = 0°C to +70°C PKG. DWG. # 16-pin plastic DIP 74F175AN SOT38-4 16-pin plastic SO 74F175AD SOT109-1 INPUT AND OUTPUT LOADING AND FAN OUT TABLE PINS DESCRIPTION 74F (U.L.) HIGH/LOW LOAD VALUE HIGH/LOW D0 – D3 Data inputs 74F175A 1.0/0.033 20µA/20µA MR Master reset input (active–Low) 74F175A 1.0/0.033 20µA/20µA CP Clock input (active rising edge) 74F175A 1.0/0.033 20µA/20µA Q0–Q3 True outputs 50/33 1.0mA/20mA Q 0–Q 3 Complementary outputs 50/33 1.0mA/20mA NOTE: One (1.0) FAST unit load is defined as: 20µA in the High state and 0.6mA in the Low state.
Philips Semiconductors Product specification 74F175AQuad D flip-flop
1996 Mar 12 3
VCC = Pin 16 GND = Pin 8 SF00719 4 5 12 13 D0 D1 D2 D3 CP MR 2 3 7 6 10 11 15 14 Q0 Q0 Q1 Q1 Q2 Q2 Q3 Q3 IEC/IEEE SYMBOL R SF00720 LOGIC DIAGRAM DQ RD VCC = Pin 16 GND = Pin 8 CP DQ RD CP DQ RD CP DQ RD CP Q SF00721 CP MR 32 6 1 1 1 0 1 4 1 5 7 Q 0Q 0 Q 1Q 1 Q 2Q 2 Q 3Q 3 FUNCTION TABLE INPUTS OUTPUTS OPERATING MR CP Dn Q n Q n MODE L X X L H Reset (clear) H ↑ h H L Load “1” H ↑ I L H Load “0” H = High voltage level h = High state must be present one setup time before the Low-to-High clock transition L = Low voltage level l = Low state must be present one setup time before the Low-to-High clock transition X = Don’t care ↑ = Low-to-High clock transition ABSOLUTE MAXIMUM RATINGS (Operation beyond the limit set forth in this table may impair the useful life of the device. Unless otherwise noted these limits are over the operating free air temperature range.) SYMBOL PARAMETER RATING UNIT VCC Supply voltage –0.5 to +7.0 V VIN Input voltage –0.5 to +7.0 V IIN Input current –30 to +5 mA VOUT Voltage applied to output in High output state –0.5 to VCC V IOUT Current applied to output in Low output state 40 mA T b O perating free air temperature range Commercial range 0 to +70 °C Tamb O erating free air tem erature range Industrial range –40 to +85 °C Tstg Storage temperature range –65 to +150 °C
Philips Semiconductors Product specification 74F175AQuad D flip-flop
1996 Mar 12 4
RECOMMENDED OPERATING CONDITIONS SYMBOL PARAMETER LIMITS UNIT MIN NOM MAX VCC Supply voltage 4.5 5.0 5.5 V VIH High-level input voltage 2.0 V VIL Low-level input voltage 0.8 V IIK Input clamp current –18 mA IOH High-level output current –1 mA IOL Low-level output current 20 mA T b Operating free air temperature range Commercial range 0 +70 °C Tamb O perating free air temperature range Industrial range –40 +85 °C DC ELECTRICAL CHARACTERISTICS (Over recommended operating free-air temperature range unless otherwise noted.) SYMBOL PARAMETER TEST LIMITS UNIT CONDITIONS 1 MIN TYP 2 MAX VOH High-level output voltage VCC = MIN, VIL = MAX, 10%V CC 2.5 VVOH High-level out ut voltage CC IL VIH = MIN, IOH = MAX 5%V CC 2.7 3.4 V VOL Low-level output voltage VCC = MIN, VIL = MAX, 10%V CC 0.30 0.5 VCC IL VIH = MIN, IOL = MAX 5%V CC 0.30 0.5 V VIK Input clamp voltage VCC = MIN, II = IIK –0.73 –1.2 V II Input current at maximum input voltageVCC = 0.0V, VI = 7.0V 100 µA IIH High-level input current VCC = MAX, VI = 2.7V 20 µA IIL Low-level input current VCC = MAX, VI = 0.5V 74F175A –20 µA IOS Short-circuit output current3 VCC = MAX –60 –150 mA ICC Supply current (total) VCC = MAX 74F175A 22 31 mA Notes to DC electrical characteristics 1. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions for the applicable type. 2. All typical values are at VCC = 5V, Tamb = 25°C. 3. Not more than one output should be shorted at a time. For testing IOS , the use of high-speed test apparatus and/or sample-and-hold techniques are preferable in order to minimize internal heating and more accurately reflect operational values. Otherwise, prolonged shorting of a high output may raise the chip temperature well above normal and thereby cause invalid readings in other parameter tests. In any sequence of parameter tests, IOS tests should be performed last. AC ELECTRICAL CHARACTERISTICS FOR 74F175A LIMITS Tamb = 25°C Tamb = 0°C to +70°C Tamb = 40°C to +85°C SYMBOL PARAMETER TEST VCC = +5V VCC = +5.0V ± 10% VCC = +5.0V ± 10% UNIT CONDITION C L = 50pF, R L = 500Ω C L = 50pF, R L = 500Ω C L = 50pF, R L = 500Ω MIN TYP MAX MIN MAX MIN MAX fmax Maximum clock frequency Waveform 1 140 160 125 110 MHz tPLH tPHL Propagation delay CP to Qn or Q n Waveform 1 3.0 4.5 4.0 6.0 6.5 8.5 2.5 4.0 7.5 9.0 2.5 4.0 8.0 10.0 ns tPLH tPHL Propagation delay MR tPHL tPHL Propagation delay MR
Philips Semiconductors Product specification 74F175AQuad D flip-flop
1996 Mar 12 5
AC SETUP REQUIREMENTS FOR 74F175A LIMITS Tamb = 25°C Tamb = 0°C to +70°C Tamb = /C004240°C to +85°C SYMBOL PARAMETER TEST VCC = +5V VCC = +5.0V ± 10% VCC = +5.0V ± 10% UNIT CONDITION C L = 50pF, R L = 500Ω C L = 50pF, R L = 500Ω C L = 50pF, R L = 500Ω MIN TYP MAX MIN MAX MIN MAX ts(H) ts(L) Setup time, High or Low Dn to CP Waveform 2 3.0 3.0 3.5 3.5 4.0 4.0 ns th(H) th(L) Hold time, High or Low Dn to CP Waveform 2 0.0 0.0 0.0 0.0 0.0 0.0 ns tw (H) tw (L) CP Pulse width High or Low Waveform 1 3.0 4.0 3.5 5.0 4.0 5.5 ns tw (L) MR Pulse width Low Waveform 3 3.5 3.5 4.0 ns tREC Recovery time MR to CP Waveform 3 4.0 4.5 5.0 ns AC WAVEFORMS For all waveforms, VM = 1.3V. CP VM VMVM tw (H) 1/fmax VMVM tPLHtw (L)tPHL Q n VMVMQ n tPLH tPHL SF00722 Waveform 1. Propagation delay for clock input to output, clock pulse width, and maximum clock frequency th(H)ts(H) CP SF00191 VM VM VMVMVM VM th(L)ts(L) Dn Waveform 2. Data setup time and hold times CP VM VM VMVM tPHL tREC MR Q n tw (L) VMQ n tPLH SF00723 Waveform 3. Master Reset pulse width, Master Reset to output delay and Master Reset to Clock recovery time
Philips Semiconductors Product specification 74F175AQuad D flip-flop
1996 Mar 12 6
TEST CIRCUIT AND WAVEFORMS tw 90% VM 10% 90% VM 10% 90% VM 10% 90% VM 10% NEGATIVE PULSE POSITIVE PULSE tw AMP (V) tTHL (tf ) INPUT PULSE REQUIREMENTS rep. rate tw tTLH tTHL 1MHz 500ns 2.5ns 2.5ns Input Pulse Definition VCC family 74F D.U.T.PULSE GENERATOR R LC LR T VIN VOUT Test Circuit for Totem-Pole Outputs DEFINITIONS: R L = Load resistor; see AC ELECTRICAL CHARACTERISTICS for value. C L = Load capacitance includes jig and probe capacitance; see AC ELECTRICAL CHARACTERISTICS for value. R T = Termination resistance should be equal to ZOUT of pulse generators. tTHL (tf ) tTLH (tr ) tTLH (tr ) AMP (V) amplitude 3.0V 1.5V VM SF00006
Philips Semiconductors Product specification 74F175*, 74F175AQuad D flip-flop
1996 Mar 12 7
- Discontinued part. Please see the Discontinued Product List. DIP16: plastic dual in-line package; 16 leads (300 mil) SOT38-4
Philips Semiconductors Product specification 74F175*, 74F175AQuad D flip-flop
1996 Mar 12 8
- Discontinued part. Please see the Discontinued Product List. SO16: plastic small outline package; 16 leads; body width 3.9 mm SOT109-1
Philips Semiconductors Product specification 74F175*, 74F175AQuad D flip-flop
1996 Mar 12 9
- Discontinued part. Please see the Discontinued Product List. NOTES
Philips Semiconductors Product specification 74F175*, 74F175AQuad D flip-flop yyyy mmm dd 10 Definitions Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Disclaimers Life support — These products are not designed for use in life support appliances, devices or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes — Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Philips Semiconductors
811 East Arques Avenue
P.O. Box 3409 Sunnyvale, California 94088–3409 Telephone 800-234-7381 Copyright Philips Electronics North America Corporation 1998 All rights reserved. Printed in U.S.A. print code Date of release: 10-98 Document order number: 9397-750-05091 /C0109 /C0110 /C0114 Data sheet status Objective specification Preliminary specification Product specification Product status Development Qualification Production Definition [1] This data sheet contains the design target or goal specifications for product development. Specification may change in any manner without notice. This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips Semiconductors reserves the right to make chages at any time without notice in order to improve design and supply the best possible product. This data sheet contains final specifications. Philips Semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. Data sheet status [1] Please consult the most recently issued datasheet before initiating or completing a design. * Discontinued part. Please see the Discontinued Product List in Section 1, page 21.