74F173 PHILIPS

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 10

Technical content

/C0109 /C0110 /C0114 74F173 Quad D-type flip-flop (3-State) Product specification IC15 Data Handbook

1990 Aug 31

Philips Semiconductors Product specification 74F173Quad D-type flip–flop (3-State) 2August 31, 1990 853–1160 00286

FEATURES

  • Edge–triggered D–type register
  • Gated clock enable for hold ”do nothing” mode
  • 3–state output buffers
  • Gated output enable control
  • Speed upgrade of N8T10 and current sink upgrade
  • Controlled output edges to minimize ground bounces
  • 48mA sinking capability

DESCRIPTION

The 74F173 is a high speed 4–bit parallel load register with clock enable control, 3–state buffered outputs, and master reset (MR). When the two clock enable (E 0 and E1) inputs are low, the data on the D inputs is loaded into the register simultaneously with low–to–high clock (CP) transition. When one or both enable inputs are high one setup time before the low–to–high clock transition, the register retains the previous data. Data inputs and clock enable inputs are fully edge–triggered and must be stable only one setup time before the low–to–high clock transition. The master reset (MR) is an active–high asynchronous input. When the MR is high, all four flip–flops are reset (cleared) independently of any other input condition. The 3–state output buffers are controlled by a 2–input NOR gate. When both output enable (OE 0 and OE1) inputs are low, the data in the register is presented at the Q output. When one or both OE inputs are high, the outputs are forced to a high impedance ”off” state. The 3–state output buffers are completely independent of the register operation; the OE transition does not affect the clock and reset operations. TYPE TYPICAL fmax TYPICAL SUPPLY CURRENT (TOTAL) 74F173 125MHz 23mA

ORDERING INFORMATION

DESCRIPTION COMMERCIAL RANGE VCC = 5V ±10%, Tamb = 0°C to +70°C PKG DWG # 16–pin plastic DIP N74F173N SOT38-4 16–pin plastic SO N74F173D SOT109-1 INPUT AND OUTPUT LOADING AND FAN OUT TABLE PINS DESCRIPTION 74F (U.L.) HIGH/ LOW LOAD VALUE HIGH/LOW D0 – D3 Data inputs 1.0/1.0 20µA/0.6mA CP Clock input 1.0/1.0 20µA/0.6mA E0, E1 Clock enable inputs 1.0/1.0 20µA/0.6mA MR Master reset input 1.0/1.0 20µA/0.6mA OE 0, OE1 Output enable inputs 1.0/1.0 20µA/0.6mA Q0 – Q3 Data outputs 750/80 15mA/48mA Note to input and output loading and fan out table 1. One (1.0) FAST unit load is defined as: 20µA in the high state and 0.6mA in the low state.

Philips Semiconductors Product specification 74F173Quad D-type flip–flop (3-State) August 31, 1990 3 PIN CONFIGURATION 107 VCCOE 0 OE 1 CP GND MR Q SF00290 LOGIC SYMBOL Q0 Q1 Q2 Q3 VCC = Pin 16 GND = Pin 8 D0 D1 D2 D3 14 13 12 11 CP MR OE0 OE1 3456 SF00291 IEC/IEEE SYMBOL R EN SF00292 FUNCTION TABLE INPUTS OUTPUTS OUTPUTS MR CP E0 E1 Dn Qn (register) H X X X X L Reset (clear) L ↑ l l l L Parallel load L ↑ l l h H L X h X X qn Hold (do nothing) L X X h X qn Notes to function table H = High–voltage level h = High state one setup time before the low–to–high clock transition L = Low–voltage level l = Low state one setup time before the low–to–high clock transition qn = Lower case letters indicate the state of the referenced input (or output) on setup time prior to the low–to–high clock transition X = Don’t care ↑ = Low–to–high clock transition

Philips Semiconductors Product specification 74F173Quad D-type flip–flop (3-State) August 31, 1990 4 FUNCTION TABLE INPUTS OUTPUTS OUTPUTS Qn (register) OE 0 OE 1 Qn L L L L Read H L L H X H X Z Disabled X X H Z Notes to function table H = High–voltage level L = Low–voltage level X = Don’t care Z = High impedance ”off” state LOGIC DIAGRAM VCC = Pin 16 GND = Pin 8 D CP Q MR Q RD D CP Q Q RD D CP Q Q RD D CP Q Q RD OE 0 OE 1 CP SF00293 ABSOLUTE MAXIMUM RATINGS (Operation beyond the limit set forth in this table may impair the useful life of the device. Unless otherwise noted these limits are over the operating free air temperature range.) SYMBOL PARAMETER RATING UNIT VCC Supply voltage –0.5 to +7.0 V VIN Input voltage –0.5 to +7.0 V IIN Input current –30 to +5 mA VOUT Voltage applied to output in high output state –0.5 to VCC V IOUT Current applied to output in low output state 96 mA Tamb Operating free air temperature range 0 to +70 °C Tstg Storage temperature range –65 to +150 °C

Philips Semiconductors Product specification 74F173Quad D-type flip–flop (3-State) August 31, 1990 5 RECOMMENDED OPERATING CONDITIONS SYMBOL PARAMETER LIMITS UNIT MIN NOM MAX VCC Supply voltage 4.5 5.0 5.5 V VIH High–level input voltage 2.0 V VIL Low–level input voltage 0.8 V IIk Input clamp current –18 mA IOH High–level output current –15 mA IOL Low–level output current 48 mA Tamb Operating free air temperature range 0 +70 °C DC ELECTRICAL CHARACTERISTICS (Over recommended operating free-air temperature range unless otherwise noted.) SYMBOL PARAMETER TEST LIMITS UNIT CONDITIONS 1 MIN TYP 2 MAX VCC = MIN, VIL = MAX, ±10%V CC 2.4 V VOH High-level output voltage VIH = MIN, IOH = MAX ±5%V CC 2.7 3.4 V VCC = MIN, VIL = MAX, ±10%V CC 2.0 V VIH = MIN, IOH = –15mA ±5%V CC 2.0 3.1 V VOL Low-level output voltage VCC = MIN, VIL = MAX, ±10%V CC 0.35 0.50 V VIH = MIN, IOL = MAX ±5%V CC 0.35 0.50 V VIK Input clamp voltage VCC = MIN, II = IIK –0.73 -1.2 V II Input current at maximum input voltage VCC = MAX, VI = 7.0V 100 µA IIH High–level input current VCC = MAX, VI = 2.7V 20 µA IIL Low–level input current VCC = MAX, VI = 0.5V –0.6 mA IOZH Off–state output current, high–level voltage appliedVCC = MAX, VO = 2.7V 50 µA IOZL Off–state output current, low–level voltage appliedVCC = MAX, VO = 0.5V –50 µA IOS Short–circuit output current3 VCC = MAX -60 -150 mA ICCH 19 26 mA ICC Supply current (total) ICCL VCC = MAX 27 37 mA ICCZ 23 32 mA Notes to DC electrical characteristics 1. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions for the applicable type. 2. All typical values are at VCC = 5V, Tamb = 25°C. 3. Not more than one output should be shorted at a time. For testing IOS , the use of high-speed test apparatus and/or sample-and-hold techniques are preferable in order to minimize internal heating and more accurately reflect operational values. Otherwise, prolonged shorting of a high output may raise the chip temperature well above normal and thereby cause invalid readings in other parameter tests. In any sequence of parameter tests, IOS tests should be performed last.

Philips Semiconductors Product specification 74F173Quad D-type flip–flop (3-State) August 31, 1990 6 AC ELECTRICAL CHARACTERISTICS LIMITS Tamb = +25°C Tamb = 0°C to +70°C SYMBOL PARAMETER TEST VCC = +5.0V VCC = +5.0V ± 10% UNIT CONDITION C L = 50pF, RL = 500Ω C L = 50pF, RL = 500Ω MIN TYP MAX MIN MAX fmax Maximum clock frequency Waveform 1 100 125 90 MHz tPLH tPHL Propagation delay CP to Qn Waveform 1 4.5 6.0 6.5 8.0 9.0 10.5 4.0 5.5 10.0 11.5 ns tPHL Propagation delay MR to Qn tPZH tPZL Output enable time to high or low level Waveform 4 Waveform 5 3.5 5.5 5.0 7.0 8.0 10.0 2.5 4.5 8.5 11.0 ns tPHZ tPLZ Output disable time from high or low level Waveform 4 Waveform 5 1.5 3.0 3.5 5.0 7.0 8.5 1.0 2.5 8.0 9.0 ns tTHL tTLH Transition time 10% to 90%, 90% to 10% Waveform 5 Waveform 4 2.0 4.0 5.0 7.5 8.0 10.0 2.0 4.0 8.5 11.0 ns AC SETUP REQUIREMENTS LIMITS Tamb = +25°C Tamb = 0°C to +70°C SYMBOL PARAMETER TEST VCC = +5.0V VCC = +5.0V ± 10% UNIT CONDITION C L = 50pF, RL = 500Ω C L= 50pF, RL = 500Ω MIN TYP MAX MIN MAX tsu (H) tsu (L) Setup time, high or low level Dn to CP Waveform 3 2.5 2.5 3.0 4.0 ns th (H) th (L) Hold time, high or low level Dn to CP Waveform 3 0 ns tsu (H) tsu (L) Setup time, high or low level E to CP Waveform 3 4.5 7.5 5.0 8.5 ns th (H) th (L) Hold time, high or low level E to CP Waveform 3 0 ns tw (H) tw (L) CP Pulse width, high or low Waveform 1 3.0 6.0 3.0 6.0 ns tw (H) MR Pulse width, high Waveform 2 3.5 3.5 ns trec Recovery time, MR to CP Waveform 2 4.5 5.5 ns AC WAVEFORMS CP VM VMVM tw (H) 1/fmax VMVM tPLHtw (L)tPHL Qn SF00294 Waveform 1. Propagation delay for clock input to output, clock pulse widths, and maximum clock frequency

Philips Semiconductors Product specification 74F173Quad D-type flip–flop (3-State) August 31, 1990 7 MR VM VM tw (H) VMCP trec VMVMQn tPHL SF00295 Waveform 2. Master reset pulse width, master reset to output delay and master reset to clock recovery time VM VM VM VM VM VM tsu(L) t h(L)tsu(H) t h(H) En, Dn CP SF00296 Waveform 3. Data and enable setup time and hold times VM VM VM tPHZtPZH OE VOH -0.3V Qn 10% 90% SF00297 Waveform 4. 3-state output enable time to high level, output disable time from high level and transition time to high level VM VM VM tPLZtPZL VOL +0.3V 3.5V OE Qn 10% 90% SF00298 Waveform 5. 3-state output enable time to low level, output disable time from low level and transition time to low level Notes to AC waveforms 1. For all waveforms, VM = 1.5V. 2. The shaded areas indicate when the input is permitted to change for predictable output performance. TEST CIRCUIT AND WAVEFORMS tw 90% VM 10% 90% VM 10% 90% VM 10% 90% VM 10% NEGATIVE PULSE POSITIVE PULSE tw AMP (V) tTHL (tf ) INPUT PULSE REQUIREMENTS rep. rate tw tTLH tTHL 1MHz 500ns 2.5ns 2.5ns Input Pulse Definition VCC family 74F D.U.T.PULSE GENERATOR R LC LR T VIN VOUT Test Circuit for Open Collector Outputs DEFINITIONS: R L = Load resistor; see AC electrical characteristics for value. C L = Load capacitance includes jig and probe capacitance; see AC electrical characteristics for value. R T = Termination resistance should be equal to ZOUT of pulse generators. tTHL (tf ) tTLH (tr ) tTLH (tr ) AMP (V) amplitude 3.0V 1.5V VM R L 7.0V SF00128 TEST SWITCH tPLZ closed tPZL closed All other open SWITCH POSITION

Philips Semiconductors Product specification 74F173Quad D-type flip-flop (3-State)

1990 Aug 31 8

DIP16: plastic dual in-line package; 16 leads (300 mil) SOT38-4

Philips Semiconductors Product specification 74F173Quad D-type flip-flop (3-State)

1990 Aug 31 9

SO16: plastic small outline package; 16 leads; body width 3.9 mm SOT109-1

Philips Semiconductors Product specification 74F173Quad D-type flip-flop (3-State) yyyy mmm dd 10 Definitions Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Disclaimers Life support — These products are not designed for use in life support appliances, devices or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes — Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Philips Semiconductors

811 East Arques Avenue

P.O. Box 3409 Sunnyvale, California 94088–3409 Telephone 800-234-7381  Copyright Philips Electronics North America Corporation 1998 All rights reserved. Printed in U.S.A. print code Date of release: 10-98 Document order number: 9397-750-05088 /C0109 /C0110 /C0114 Data sheet status Objective specification Preliminary specification Product specification Product status Development Qualification Production Definition [1] This data sheet contains the design target or goal specifications for product development. Specification may change in any manner without notice. This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips Semiconductors reserves the right to make chages at any time without notice in order to improve design and supply the best possible product. This data sheet contains final specifications. Philips Semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. Data sheet status [1] Please consult the most recently issued datasheet before initiating or completing a design.