DATASHEET SEARCH SITE

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 10

Technical content

/C0080 /C0115 /C0111/C0110/C0111 /C0115 Product specification Supersedes data of 1995 Sep 22 74F164 8-bit serial-in parallel-out shift register

2000 Dec 18

Philips Semiconductors Product specification 74F1648-bit serial-in parallel-out shift register

22000 Dec 18 853-0348 25264

FEATURES

  • Gated serial data inputs
  • Typical shift frequency of 100MHz
  • Asynchronous Master Reset
  • Buffered clock and data inputs
  • Fully synchronous data transfer
  • Industrial temperature range available (–40 to +85 °C)

DESCRIPTION

The 74F164 is an 8-bit edge-triggered shift register with serial data entry and an output from each of the eight stages. Data is entered through one of two inputs (Dsa, Dsb); either input can be used as an active High enable for data entry through the other input. Both inputs must be connected together or an unused input must be tied High. Data shifts one place to the right on each Low-to-High transition of the clock (CP) input, and enters into Q0 the logical AND of the two data inputs (Dsa, Dsb) that existed one setup time before the rising edge. A Low level on the Master Reset (MR) input overrides all other inputs and clears the register asynchronously, forcing all outputs Low. PIN CONFIGURATION SF00717 Dsa Dsb GND VCC MR CP TYPE TYPICAL fmax TYPICAL SUPPLY CURRENT (TOTAL) 74F164 100MHz 33 mA

ORDERING INFORMATION

DRAWINGDESCRIPTION COMMERCIAL RANGE VCC = 5 V ±10%, Tamb = 0 to +70 °C INDUSTRIAL RANGE VCC = 5 V ±10%, Tamb = –40 to +85 °C DRAWING NUMBER 14-pin plastic DIP 74F164N I74F164N SOT27-1 14-pin plastic SO 74F164D I74F164D SOT108-1 INPUT AND OUTPUT LOADING AND FAN OUT TABLE PINS DESCRIPTION 74F (U.L.) HIGH / LOW LOAD VALUE HIGH / LOW Dsa, Dsb Data inputs 1.0 / 1.0 20 µA / 0.6 mA CP Clock pulse input (active rising edge) 1.0 / 1.0 20 µA / 0.6 mA MR Master reset input (active-Low) 1.0 / 1.0 20 µA / 0.6 mA Q0 – Q7 Data outputs 50 / 33 1.0 mA / 20 mA One (1.0) FAST unit load is defined as: 20 µA in the High state and 0.6 mA in the Low state. LOGIC SYMBOL Dsa Dsb VCC = Pin 14 GND = Pin 7 Q1 Q2 Q3 Q4 Q5 Q6 Q7 CP MR SF00713 3 4 5 6 10 11 12 13 IEC/IEEE SYMBOL SRG8 R C1/→ SF00714

Philips Semiconductors Product specification 74F1648-bit serial-in parallel-out shift register

2000 Dec 18 3

VCC = Pin 14 GND = Pin 7 DQ RD DQ RD DQ RD DQ RD DQ RD DQ RD DQ RD SF00715 CPCPCPCPCPCPCPCP FUNCTION TABLE INPUTS OUTPUTS OPERATING MODE MR CP Dsa Dsb Q0 Q1 Q2 Q3 Q4 Q5 Q6 Q7 L X X X L L L L L L L L Reset (Clear) H ↑ l l L q0 q1 q2 q3 q4 q5 q6 H ↑ l h L q0 q1 q2 q3 q4 q5 q6 Shift H ↑ h l L q0 q1 q2 q3 q4 q5 q6 H ↑ h h H q0 q1 q2 q3 q4 q5 q6 H = High voltage level h = High voltage level one setup time prior to the Low-to-High clock transition. L = Low voltage level l = Low voltage level one setup time prior to the Low-to-High clock transition. qn = Lower case letter indicate the state of the referenced output one setup time prior to the Low-to-High clock transition. X = Don’t care ↑ = Low-to-High clock transition ABSOLUTE MAXIMUM RATINGS (Operation beyond the limit set forth in this table may impair the useful life of the device. Unless otherwise noted these limits are over the operating free air temperature range.) SYMBOL PARAMETER RATING UNIT VCC Supply voltage –0.5 to +7.0 V VIN Input voltage –0.5 to +7.0 V IIN Input current –30 to +5 mA VOUT Voltage applied to output in High output state –0.5 to VCC V IOUT Current applied to output in Low output state 40 mA T b O perating free-air temperature range Commercial Range 0 to +70 °CTamb O erating free-air tem erature range Industrial Range –40 to +85 Tstg Storage temperature range –65 to +150 °C RECOMMENDED OPERATING CONDITIONS SYMBOL PARAMETER LIMIT UNITSYMBOL PARAMETER MIN NOM MAX UNIT VCC Supply voltage 4.5 5.0 5.5 V VIH High-level input voltage 2.0 V VIL Low-level input voltage 0.8 V IIk Input clamp current –18 mA IOH High-level output current –1 mA IOL Low-level output current 20 mA T b O perating free-air temperature range Commercial Range 0 +70 °CTamb O erating free-air tem erature range Industrial Range –40 +85

Philips Semiconductors Product specification 74F1648-bit serial-in parallel-out shift register

2000 Dec 18 4

DC ELECTRICAL CHARACTERISTICS (Over recommended operating free-air temperature range unless otherwise noted.) SYMBOL PARAMETER TEST LIMITS UNIT SYMBOL PARAMETER CONDITIONS 1 MIN TYP 2 MAX VOH High-level output voltage VCC = MIN, VIL = MAX, ±10%V CC 2.5 V VOH High-level out ut voltage CC IL VIH = MIN, IOH = MAX ±5%V CC 2.7 3.4 V VOL Low-level output voltage VCC = MIN, VIL = MAX, ±10%V CC 0.30 0.50 V CC IL VIH = MIN, IOL = MAX ±5%V CC 0.30 0.50 V VIK Input clamp voltage VCC = MIN, II = IIK –0.73 –1.2 V II Input current at maximum input voltageVCC = MAX, VI = 7.0 V 100 µA IIH High-level input current VCC = MAX, VI = 2.7 V 20 µA IILL Low-level input current VCC = MAX, VI = 0.5 V –0.6 mA IOS Short-circuit output current3 VCC = MAX –60 –150 mA ICC Supply current (total) 4 VCC = MAX 33 55 mA Notes to DC electrical characteristics 1. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions for the applicable type. 2. All typical values are at VCC = 5 V, Tamb = 25 °C. 3. Not more than one output should be shorted at a time. For testing IOS , the use of high-speed test apparatus and/or sample-and-hold techniques are preferable in order to minimize internal heating and more accurately reflect operational values. Otherwise, prolonged shorting of a High output may raise the chip temperature well above normal and thereby cause invalid readings in other parameter tests. In any sequence of parameter test, IOS tests should be performed last. 4. Measure ICC with the serial inputs grounded, the clock input at 2.4 V, and a momentary ground, then applied to Master Reset, and all outputs open. APPLICATION RESET CLOCK DATA ENABLE Dsa Dsb Dsa Dsb CP MR D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 D14 D15 CP MR H 74F164 74F164 Q0 Q1 Q2 Q3 Q4 Q5 Q6 Q7 Q0 Q1 Q2 Q3 Q4 Q5 Q6 Q7 SF00716 The 74F164 can be cascaded to form synchronous shift registers of longer length. Here, two devices are combined to form a 16-bit shift register.

Philips Semiconductors Product specification 74F1648-bit serial-in parallel-out shift register

2000 Dec 18 5

AC ELECTRICAL CHARACTERISTICS LIMITS Tamb = +25 °C Tamb = 0 to +70 °C Tamb = –40 to +85 °C SYMBOL PARAMETER TEST CONDITION Tamb +25 C VCC = 5 V C L = 50 pF R 500 Ω Tamb 0 to +70 C VCC = +5 V±10% C L = 50 pF R 500 Ω Tamb 40 to +85 C VCC = +5 V±10% C L = 50 pF R 500 Ω UNIT R L = 500 Ω R L = 500 Ω R L = 500 Ω MIN TYP MAX MIN MAX MIN MAX fmax Maximum clock frequency Waveform 1 80 100 80 80 MHz tPLH tPHL Propagation delay CP to Qn Waveform 1 3.0 5.0 5.0 7.0 8.0 10.0 2.5 5.0 9.0 11.0 2.5 5.0 9.0 11.0 ns tPHL Propagation delay MR AC SETUP REQUIREMENTS LIMITS Tamb = +25 °C Tamb = 0 to +70 °C Tamb = –40 to +85 °C SYMBOL PARAMETER TEST CONDITION Tamb +25 C VCC = 5 V C L = 50 pF R 500 Ω Tamb 0 to +70 C VCC = +5 V±10% C L = 50 pF R 500 Ω Tamb 40 to +85 C VCC = +5 V±10% C L = 50 pF R 500 Ω UNIT R L = 500 Ω R L = 500 Ω R L = 500 Ω MIN TYP MAX MIN MAX MIN MAX ts(H) tS(L) Setup time, High or Low D n to CP Waveform 2 7.0 7.0 7.0 7.0 7.0 7.0 ns th(H) th(L) Hold time, High or Low D n to CP Waveform 2 1.0 1.0 2.0 2.0 2.0 2.0 ns tw (H) tw (L) CP Pulse width High or Low Waveform 1 4.0 7.0 4.0 7.0 4.0 7.0 ns tw (L) MR Pulse wicth Low Waveform 3 7.0 7.0 7.0 ns tREC Recovery time MR to CP Waveform 3 7.0 7.0 7.0 ns AC WAVEFORMS For all waveforms, VM = 1.5 V. The shaded areas indicate when the input is permitted to change for predictable output performance. CP VM VMVM tw (H) 1/fmax VMVM tPLHtw (L)tPHL Qn SF00294 Waveform 1. Propagation delay for Clock input to output, Clock Pulse width, and maximum Clock frequency th(H)ts(H) CP SF00191 VM VM VMVMVM VM th(L)ts(L) Dn Waveform 2. Data setup and hold times VM SF00158 MR Qn VM tw (L) tPHL VM tREC CP VM Waveform 3. Master Reset pulse width, Master Reset to output delay and Master Reset to Clock recovery time

Philips Semiconductors Product specification 74F1648-bit serial-in parallel-out shift register

2000 Dec 18 6

TEST CIRCUIT AND WAVEFORMS tw 90% VM 10% 90% VM 10% 90% VM 10% 90% VM 10% NEGATIVE PULSE POSITIVE PULSE tw AMP (V) 0 V 0 V tTHL (tf ) INPUT PULSE REQUIREMENTS rep. rate tw tTLH tTHL 1 MHz 500 ns 2.5 ns 2.5 ns Input Pulse Definition VCC family 74F D.U.T.PULSE GENERATOR R LC LR T VIN VOUT Test Circuit for Totem-Pole Outputs DEFINITIONS: R L = Load resistor; see AC ELECTRICAL CHARACTERISTICS for value. C L = Load capacitance includes jig and probe capacitance; see AC ELECTRICAL CHARACTERISTICS for value. R T = Termination resistance should be equal to ZOUT of pulse generators. tTHL (tf ) tTLH (tr ) tTLH (tr ) AMP (V) amplitude 3.0 V 1.5 V VM SF00006

Philips Semiconductors Product specification 74F1648-bit serial-in parallel-out shift register

2000 Dec 18 7

DIP14: plastic dual in-line package; 14 leads (300 mil) SOT27-1

Philips Semiconductors Product specification 74F1648-bit serial-in parallel-out shift register

2000 Dec 18 8

SO14: plastic small outline package; 14 leads; body width 3.9 mm SOT108-1

Philips Semiconductors Product specification 74F1648-bit serial-in parallel-out shift register

2000 Dec 18 9

Philips Semiconductors Product specification 74F1648-bit serial-in parallel-out shift register

2000 Dec 18 10

Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Disclaimers Life support — These products are not designed for use in life support appliances, devices or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes — Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Philips Semiconductors

811 East Arques Avenue

P.O. Box 3409 Sunnyvale, California 94088–3409 Telephone 800-234-7381  Copyright Philips Electronics North America Corporation 2001 All rights reserved. Printed in U.S.A. Date of release: 01-01 Document order number: 9397 750 07889 /C0080 /C0115 /C0111/C0110/C0111 /C0115 Data sheet status Objective specification Preliminary specification Product specification Product status Development Qualification Production Definition [1] This data sheet contains the design target or goal specifications for product development. Specification may change in any manner without notice. This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips Semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. This data sheet contains final specifications. Philips Semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. Data sheet status [1] Please consult the most recently issued datasheet before initiating or completing a design.