74F161A PHILIPS

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 14

Technical content

/C0109 /C0110 /C0114 74F160A *, 74F161A, 74F162A *, 74F163A 4-bit binary counter Product specification 1996 Jan 29 INTEGRATED CIRCUITS IC15 Data Handbook * Discontinued part. Please see the Discontinued Product List in Section 1, page 21.

Philips Semiconductors Product specification 74F161A, 74F163A4-bit binary counters

21996 Jan 29 853–0347 16300

FEATURES

  • Synchronous counting and loading
  • Two count enable inputs for n-bit cascading
  • Positive edge-triggered clock
  • Asynchronous Master Reset (74F161A)
  • Synchronous Reset (74F163A)
  • High speed synchronous expansion
  • Typical count rate of 130MHz
  • Industrial range (–40°C to +85°C) available

DESCRIPTION

4-bit binary counters feature an internal carry look-ahead and can be used for high-speed counting. Synchronous operation is provided by having all flip-flops clocked simultaneously on the positive-going edge of the clock. The clock input is buffered. The outputs of the counters may be preset to High or Low level. A Low level at the Parallel Enable (PE ) input disables the counting action and causes the data at the D0–D3 inputs to be loaded into the counter on the positive-going edge of the clock (provided that the setup and hold requirements for PE are met). Preset takes place regardless of the levels at Count Enable (CEP, CET) inputs. A Low level at the Master Reset (MR) input sets all the four outputs of the flip-flops (Q0 – Q3) in 74F161A to Low levels, regardless of the levels at CP, PE, CET and CEP inputs (thus providing an asynchronous clear function). For the 74F163A, the clear function is synchronous. A Low level at the Synchronous Reset (SR ) input sets all four outputs of the flip-flops (Q0 – Q3) to Low levels after the next positive-going transition on the clock (CP) input (provided that the setup and hold time requirements for SR are met). This action occurs regardless of the levels at PE, CET, and CEP inputs. The synchronous reset feature enables the designer to modify the maximum count with only one external NAND gate (see Figure 1). The carry look-ahead simplifies serial cascading of the counters. Both Count Enable (CEP and CET) inputs must be High to count. The CET input is fed forward to enable the TC output. The TC output thus enabled will produce a High output pulse of a duration approximately equal to the High level output of Q0. This pulse can be used to enable the next cascaded stage (see Figure 2). The TC output is subjected to decoding spikes due to internal race conditions. Therefore, it is not recommended for use as clock or asynchronous reset for flip-flops, registers, or counters. TYPE TYPICAL fMAX TYPICAL SUPPLY CURRENT (TOTAL) 74F161A 74F163A 130MHz 46mA

ORDERING INFORMATION

DRAWINGDESCRIPTION COMMERCIAL RANGE VCC = 5V ±10%, Tamb = 0°C to +70°C INDUSTRIAL RANGE VCC = 5V ±10%, Tamb = –40°C to +85°C DRAWING NUMBER 16-pin plastic DIP N74F161AN, N74F163AN I74F161AN, I74F163AN SOT38-4 16-pin plastic SO N74F161AD, N74F163AD I74F161AD, I74F163AD SOT109-1 INPUT AND OUTPUT LOADING AND FAN-OUT TABLE PINS DESCRIPTION 74F (U.L.) HIGH/LOW LOAD VALUE HIGH/LOW D0 – D3 Data inputs 1.0/1.0 20µA/0.6mA CEP Count Enable Parallel input 1.0/1.0 20µA/0.6mA CET Count Enable Trickle input 1.0/2.0 20µA/1.2mA CP Clock input (active rising edge) 1.0/1.0 20µA/0.6mA PE Parallel Enable input (active Low) 1.0/2.0 20µA/1.2mA MR Asynchronous Master Reset input (active Low) for 74F161A 1.0/1.0 20µA/0.6mA SR Synchronous Reset input (active Low) for 74F163A 1.0/1.0 20µA/0.6mA TC Terminal count output 50/33 1.0mA/20mA Q0 – Q3 Flip-flop outputs 50/33 1.0mA/20mA NOTE: One (1.0) FAST unit load is defined as: 20µA in the High state and 0.6mA in the Low state.

Philips Semiconductors Product specification 74F161A, 74F163A4-bit binary counters

1996 Jan 29 3

14 13 12 11VCC = Pin 16 GND = Pin 8 PE CEP CET CP D1 D2 SF00658 D3D0 1M R TC 15 74F163A LOGIC SYMBOL Q0 Q1 Q2 Q3 14 13 12 11VCC = Pin 16 GND = Pin 8 PE CEP CET CP D1 D2 SF00659 D3D0 1S R TC 15 74F161A LOGIC SYMBOL (IEEE/IEC) SF00660 3 1,2 D 9 M1

154 CT=15

2 C2 /1,3,4+

74F163A LOGIC SYMBOL (IEEE/IEC) SF00661 3 1,2 D 9 M1

Philips Semiconductors Product specification 74F161A, 74F163A4-bit binary counters

1996 Jan 29 4

APPLICATIONS

+V CC Figure 1. Maximum count modifying scheme Figure 2. Synchronous multistage counting scheme

Philips Semiconductors Product specification 74F161A, 74F163A4-bit binary counters

1996 Jan 29 5

74F163A MODE SELECT – FUNCTION TABLE INPUTS OUTPUTS OPERATING MODESR CP CEP CET PE Dn Qn TC OPERATING MODE l ↑ X X X X L L Reset (clear) h ↑ X X l l L L Parallel loadh ↑ X X l h H (2) Parallel load h ↑ h h h X count (2) Count h X l X h X qn (2) Hold (do nothing) h X X l h X qn L Hold (do nothing) H = High voltage level h = High voltage level one setup prior to the Low-to-High clock transition L = Low voltage level l = Low voltage level one setup prior to the Low-to-High clock transition q n = Lower case letters indicate the state of the referenced output prior to the Low-to-High clock transition X = Don’t care ↑ = Low-to-High clock transition (1) = The TC output is High when CET is High and the counter is at Terminal Count (HHHH for 74F161A) (2) = The TC output is High when CET is High and the counter is at Terminal Count (HHHH for 74F163A) 74F161A LOGIC DIAGRAM RD CP Q Q RD CP Q Q RD CP Q Q RD CP Q Q 13 Q1 11 Q3 TC 5D2 CEP CET PE MR CP SF00662 VCC = Pin 16 GND = Pin 8

Philips Semiconductors Product specification 74F161A, 74F163A4-bit binary counters

1996 Jan 29 6

D CP Q Q D CP Q Q D CP Q Q D CP Q Q 13 Q1 11 Q3 TC 6D3 3D0 CEP CET PE SR 2CP SF00663 VCC = Pin 16 GND = Pin 8 ABSOLUTE MAXIMUM RATINGS (Operation beyond the limits set forth in this table may impair the useful life of the device. Unless otherwise noted these limits are over the operating free-air temperature range.) SYMBOL PARAMETER RATING UNIT VCC Supply voltage –0.5 to +7.0 V VIN Input voltage –0.5 to +7.0 V IIN Input current –30 to +5 mA VOUT Voltage applied to output in High output state –0.5 to VCC V IOUT Current applied to output in Low output state 40 mA T O perating free air temperature range Commercial range 0 to +70 °C Tamb Operating free-air temperature range Industrial range –40 to +85 °C Tstg Storage temperature range –65 to +150 °C

Philips Semiconductors Product specification 74F161A, 74F163A4-bit binary counters

1996 Jan 29 7

RECOMMENDED OPERATING CONDITIONS SYMBOL PARAMETER LIMITS UNITSYMBOL PARAMETER MIN NOM MAX UNIT VCC Supply voltage 4.5 5.0 5.5 V VIH High-level input voltage 2.0 V VIL Low-level input voltage 0.8 V IIK Input clamp current –18 mA IOH High-level output current –1 mA IOL Low-level output current 20 mA T O perating free air temperature range Commercial range 0 +70 °C Tamb Operating free-air temperature range Industrial range –40 +85 °C DC ELECTRICAL CHARACTERISTICS (Over recommended operating free-air temperature range unless otherwise noted.) SYMBOL PARAMETER TEST CONDITIONS 1 LIMITS UNITSYMBOL PARAMETER TEST CONDITIONS 1 MIN TYP 2 MAX UNIT VO High level output voltage VCC = MIN, VIL = MAX, IO = MAX ±10%V CC 2.5 V VOH High-level output voltage CC , IL , VIH = MIN IOH = MAX ±5%V CC 2.7 3.4 V VO Low level output voltage VCC = MIN, VIL = MAX, IO = MAX ±10%V CC 0.30 0.50 V VOL Low-level output voltage CC , IL , VIH = MIN IOL = MAX ±5%V CC 0.30 0.50 V VIK Input clamp voltage VCC = MIN, II = IIK –0.73 –1.2 V II Input current at maximum input voltageVCC = MAX, VI = 7.0V 100 µA IIH High-level input current VCC = MAX, VI = 2.7V 20 µA I Low level input current CET, PE VCC = MAX V =05 V –1.2 mA IIL Low-level input current others VCC = MAX , VI = 0.5V –0.6 mA IOS Short-circuit output current3 VCC = MAX -60 –150 mA ICC Supply current (total) ICCH VCC = MAX 42 55 mA ICC Supply current (total) ICCL VCC = MAX 49 65 mA NOTES: 1. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions for the applicable type. 2. All typical values are at VCC = 5V, Tamb = 25°C. 3. Not more than one output should be shorted at a time. For testing IOS , the use of high-speed test apparatus and/or sample-and-hold techniques are preferable in order to minimize internal heating and more accurately reflect operational values. Otherwise, prolonged shorting of a High output may raise the chip temperature well above normal and thereby cause invalid readings in other parameter tests. In any sequence of parameter tests, IOS tests should be performed last.

Philips Semiconductors Product specification 74F161A, 74F163A4-bit binary counters

1996 Jan 29 8

AC ELECTRICAL CHARACTERISTICS LIMITS SYMBOL PARAMETER TEST CONDITION Tamb = +25°C VCC = +5.0V C L = 50pF R L = 500Ω Tamb = 0°C to +70°C VCC = +5.0V ± 10% C L = 50pF R L = 500Ω Tamb = –40°C to +85°C VCC = +5.0V ± 10% C L = 50pF R L = 500Ω UNIT MIN TYP MAX MIN MAX MIN MAX fmax Maximum clock frequency Waveform 1 100 130 90 75 MHz tPLH tPHL Propagation delay CP to Qn (PE = High) Waveform 1 2.0 4.0 4.0 6.5 6.5 10.0 2.0 4.0 7.0 11.0 2.0 4.0 7.0 11.0 ns tPLH tPHL Propagation delay CP to Qn (PE = Low) Waveform 1 2.0 3.5 4.5 5.5 6.5 8.5 2.0 3.5 7.5 9.5 2.0 3.5 7.5 9.5 ns tPLH tPHL Propagation delay CP to TC Waveform 1 5.0 4.5 7.5 7.5 10.5 10.5 5.0 4.0 11.5 11.5 5.0 4.0 11.5 11.5 ns tPLH tPHL Propagation delay CET to TC Waveform 2 1.5 2.5 3.5 5.0 6.5 7.5 1.5 2.5 7.0 8.0 1.5 2.5 7.0 8.0 ns tPHL Propagation delay MR tPHL Propagation delay MR AC SETUP REQUIREMENTS LIMITS SYMBOL PARAMETER TEST CONDITION Tamb = +25°C VCC = +5.0V C L = 50pF R L = 500Ω Tamb = 0°C to +70°C VCC = +5.0V ± 10% C L = 50pF R L = 500Ω Tamb = –40°C to +85°C VCC = +5.0V ± 10% C L = 50pF R L = 500Ω UNIT MIN TYP MIN MIN ts(H) ts(L) Setup time, High or Low Dn to CP Waveform 6 5.0 5.0 5.0 5.0 5.0 5.0 ns th(H) th(L) Hold time, High or Low Dn to CP Waveform 6 0 ns ts(H) ts(L) Setup time, High or Low PE or SR to CP Waveform 5 or 6 9.0 6.5 9.5 7.0 9.5 7.0 ns th(H) th(L) Hold time, High or Low PE or SR to CP Waveform 5 or 6 ns ts(H) ts(L) Setup time, High or Low CET or CEP to CP Waveform 4 10.5 6.0 10.5 7.0 10.5 7.0 ns th(H) th(L) Hold time, High or Low CET or CEP to CP Waveform 4 0 ns tw (H) tw (L) CP pulse width (Load) High or Low Waveform 1 4.0 5.0 4.0 5.5 4.0 7.0 ns tw (H) tw (L) CP pulse width (Count) High or Low Waveform 1 4.0 6.0 4.0 7.0 4.0 7.0 ns tw (L) MR pulse width Low ’F161A Waveform 3 4.5 4.5 4.5 ns tREC Recovery time MR to CP ’F161A Waveform 3 6.0 6.5 6.5 ns

Philips Semiconductors Product specification 74F161A, 74F163A4-bit binary counters

1996 Jan 29 9

For all waveforms, VM = 1.5V. The shaded areas indicate when the input is permitted to change for predictable output performance. VM SF00667 VM VM VM VM 1/fMAX tw (H) tw (L) tPLH tPHL CP Qn, TC Waveform 1. Propagation Delay, Clock Input to Output, Clock Pulse Width, and Maximum Clock Frequency VM SF00668 VM VM tPLH CET TC VM tPHL Waveform 2. Propagation Delay, CET Input to TC Output SF00669 MR CP VM VM VM VM tw (L) tPHL tREC Qn, TC Waveform 3. Master Reset Pulse Width, Master Reset to Output Delay, and Master Reset to Recovery Time SF00670 VM VM VM VM VM VM ts(H) ts(L)th(H) t h(L) CEP CET CP Waveform 4. CEP and CET Reset Setup and Hold Times SF00671 VM VM VM VM VM VM ts(L) ts(H)th(L) t h(H) SR CP Waveform 5. Synchronous Reset Setup and Hold Times SF00672 VM VM VM VM VM VM ts(L) ts(H)th(L) t h(H) PE CP VM VMDn ts th Waveform 6. Parallel Data and Parallel Enable Setup and Hold Times

Philips Semiconductors Product specification 74F161A, 74F163A4-bit binary counters

1996 Jan 29 10

TEST CIRCUIT AND WAVEFORMS tw 90% VM 10% 90% VM 10% 90% VM 10% 90% VM 10% NEGATIVE PULSE POSITIVE PULSE tw AMP (V) tTHL (tf ) INPUT PULSE REQUIREMENTS rep. rate tw tTLH tTHL 1MHz 500ns 2.5ns 2.5ns Input Pulse Definition VCC family 74F D.U.T.PULSE GENERATOR R LC LR T VIN VOUT Test Circuit for Totem-Pole Outputs DEFINITIONS: R L = Load resistor; see AC ELECTRICAL CHARACTERISTICS for value. C L = Load capacitance includes jig and probe capacitance; see AC ELECTRICAL CHARACTERISTICS for value. R T = Termination resistance should be equal to ZOUT of pulse generators. tTHL (tf ) tTLH (tr ) tTLH (tr ) AMP (V) amplitude 3.0V 1.5V VM SF00006

Philips Semiconductors Product specification 74F160A *, 74F161A, 74F162A *, 74F163A4-bit binary counters

1996 Jan 29 11

  • Discontinued part. Please see the Discontinued Product List in Section 1, page 21. DIP16: plastic dual in-line package; 16 leads (300 mil) SOT38-4

Philips Semiconductors Product specification 74F160A *, 74F161A, 74F162A *, 74F163A4-bit binary counters

1996 Jan 29 12

  • Discontinued part. Please see the Discontinued Product List in Section 1, page 21. SO16: plastic small outline package; 16 leads; body width 3.9 mm SOT109-1

Philips Semiconductors Product specification 74F160A *, 74F161A, 74F162A *, 74F163A4-bit binary counters

1996 Jan 29 13

  • Discontinued part. Please see the Discontinued Product List in Section 1, page 21. NOTES

Philips Semiconductors Product specification 74F160A*, 74F161A, 74F162A*, 74F163A4-bit binary counter yyyy mmm dd 14 Definitions Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Disclaimers Life support — These products are not designed for use in life support appliances, devices or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes — Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Philips Semiconductors

811 East Arques Avenue

P.O. Box 3409 Sunnyvale, California 94088–3409 Telephone 800-234-7381  Copyright Philips Electronics North America Corporation 1998 All rights reserved. Printed in U.S.A. print code Date of release: 10-98 Document order number: 9397-750-05084 /C0109 /C0110 /C0114 Data sheet status Objective specification Preliminary specification Product specification Product status Development Qualification Production Definition [1] This data sheet contains the design target or goal specifications for product development. Specification may change in any manner without notice. This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips Semiconductors reserves the right to make chages at any time without notice in order to improve design and supply the best possible product. This data sheet contains final specifications. Philips Semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. Data sheet status [1] Please consult the most recently issued datasheet before initiating or completing a design. * Discontinued part. Please see the Discontinued Product List in Section 1, page 21.