74F1604 PHILIPS
Document overview
- Manufacturer or author: Provided By digicamel.com
- PDF pages: 10
Technical content
/C0109 /C0110 /C0114 74F1604 Latch Product specification IC15 Data Handbook
1990 Oct 04
Philips Semiconductors Product specification 74F1604Latch 2October 4, 1990 853 0088 00619
FEATURES
- High impedance NPN base inputs for reduced loading (20µA in high and low state)
- Stores 16–bit wide data inputs, multiplexed 8–bit outputs
- Propagation delay 7.0ns typical
- Power supply current 70mA typical
DESCRIPTION
The 74F1604 is a dual octal transparent latch. Organized as 8–bit A and B latches, the latch outputs are connected by pairs to eight 2–input multiplexers. A select (SELECT A/B ) input determines whether the A or B latch contents are multiplexed to the eight outputs. Data from the B inputs are selected when SELECT A/B is low; data from the A inputs are selected when SELECT A/B is high. Data enters the latch on the falling edge of the latch enable (LE) input. The latch remains transparent to the data inputs while LE is low, and stores the data that is present one setup time before the low–to–high latch enable transition. TYPE TYPICAL PROPAGATION DELAY TYPICAL SUPPLY CURRENT (TOTAL) 74F1604 7.0ns 70mA
ORDERING INFORMATION
DESCRIPTION COMMERCIAL RANGE VCC = 5V ±10%, Tamb = 0°C to +70°C PKG DWG # 28–pin plastic DIP N74F1604N SOT117-2 28–pin plastic SOL N74F1604D SOT136-1 INPUT AND OUTPUT LOADING AND FAN OUT TABLE PINS DESCRIPTION 74F (U.L.) HIGH/LOW LOAD VALUE HIGH/LOW A0 – A7 Data inputs 1.0/0.033 20µA/20µA B0 – B7 Data inputs 1.0/0.033 20µA/20µA SELECT A/B Select input 1.0/0.033 20µA/20µA LE Latch enable input (active low) 1.0/0.033 20µA/20µA Q0 – Q7 Data outputs 50/33 1.0mA/20mA Note to input and output loading and fan out table One (1.0) FAST unit load is defined as: 20µA in the high state and 0.6mA in the low state. PIN CONFIGURATION 10 19
28 VCC
Q SF00553 LOGIC SYMBOL LE SELCT A/B A0 B0 A1 B1 A2 B2 A3 B3 A4 B4 A5 B5 A6B6A7 B7 3 4 56789 1 0 2 7 2 6 2 5 2 4 2 3 2 2 2 1 2 0 15 13 12 11 16 17 18 19 Q0 Q1 Q2 Q3 Q4 Q5 Q6 Q7 VCC = Pin 28 GND = Pin 14 SF00554 IEC/IEEE SYMBOL 1D 2 1D 2 SF00555
Philips Semiconductors Product specification 74F1604Latch October 4, 1990 3 LOGIC DIAGRAM V CC = Pin 28 GND = Pin 14 D E Q Q D E D E Q Q D E D E Q Q D E D E Q Q D E D E Q Q D E D E Q Q D E D E Q Q D E D E Q Q D E SELECT A/B LE SF00556 FUNCTION TABLE INPUTS OUTPUTS OUTPUTS OPERATING MODE A0 – A7 B0 –B7 SELECT A/B LE Q0 – Q7 A data B data L L B data Enable and read register A data B data H L A data Enable and read register X X X H NC Hold A data B data l ↑ B data Latch and read register A data B data h ↑ A data Latch and read register Notes to function table H = High–voltage level h = High–voltage level one setup time before the low–to–high latch enable transition L = Low–voltage level l = Low–voltage level one setup time before the low–to–high latch enable transition NC= No change ( If SELECT A/B is toggled and the A latched data is different from B latched data then the output will change accordingly.) X = Don’t care ↑ = Low–to–high latch enable transition
Philips Semiconductors Product specification 74F1604Latch October 4, 1990 4 ABSOLUTE MAXIMUM RATINGS (Operation beyond the limit set forth in this table may impair the useful life of the device. Unless otherwise noted these limits are over the operating free air temperature range.) SYMBOL PARAMETER RATING UNIT VCC Supply voltage –0.5 to +7.0 V VIN Input voltage –0.5 to +7.0 V IIN Input current –30 to +5 mA VOUT Voltage applied to output in high output state –0.5 to VCC V IOUT Current applied to output in low output state 40 mA Tamb Operating free air temperature range 0 to +70 °C Tstg Storage temperature range –65 to +150 °C RECOMMENDED OPERATING CONDITIONS SYMBOL PARAMETER LIMITS UNIT MIN NOM MAX VCC Supply voltage 4.5 5.0 5.5 V VIH High–level input voltage 2.0 V VIL Low–level input voltage 0.8 V IIk Input clamp current –18 mA IOH High–level output current –1 mA IOL Low–level output current 20 mA Tamb Operating free air temperature range 0 +70 °C DC ELECTRICAL CHARACTERISTICS (Over recommended operating free-air temperature range unless otherwise noted.) SYMBOL PARAMETER TEST LIMITS UNIT CONDITIONS 1 MIN TYP 2 MAX IOH = –1mA ±10%V CC 2.5 V VOH High-level output voltage VCC = MIN, VIL = MAX, ±5%V CC 2.7 3.4 V VIH = MIN IOH = –3mA ±10%V CC 2.4 V ±5%V CC 2.7 3.3 V VOL Low-level output voltage VCC = MIN, VIL = MAX, IOL = MAX ±10%V CC 0.30 0.50 V VIH = MIN ±5%V CC 0.30 0.50 V VIK Input clamp voltage VCC = MIN, II = IIK –0.73 -1.2 V II Input current at maximum input voltageVCC = MAX, VI = 7.0V 100 µA IIH High–level input current VCC = MAX, VI = 2.7V 20 µA IIL Low–level input current VCC = MAX, VI = 0.5V –20 µA IOS Short–circuit output current3 VCC = MAX -60 -150 mA ICC Supply current (total) ICCH VCC = MAX 60 80 mA ICCL 75 100 mA Notes to DC electrical characteristics 1. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions for the applicable type. 2. All typical values are at VCC = 5V, Tamb = 25°C. 3. Not more than one output should be shorted at a time. For testing IOS , the use of high-speed test apparatus and/or sample-and-hold techniques are preferable in order to minimize internal heating and more accurately reflect operational values. Otherwise, prolonged shorting of a high output may raise the chip temperature well above normal and thereby cause invalid readings in other parameter tests. In any sequence of parameter tests, IOS tests should be performed last.
Philips Semiconductors Product specification 74F1604Latch October 4, 1990 5 AC ELECTRICAL CHARACTERISTICS LIMITS Tamb = +25°C Tamb = 0°C to +70°C SYMBOL PARAMETER TEST VCC = +5.0V VCC = +5.0V ± 10% UNIT CONDITION C L = 50pF, RL = 500Ω C L = 50pF, R = 500Ω MIN TYP MAX MIN MAX tPLH tPHL Propagation delay SELECT A/B to Qn (non–inverting) Waveform 2 3.0 3.5 5.5 6.5 8.5 10.0 2.5 3.0 9.0 11.5 ns tPLH tPHL Propagation delay SELECT A/B to Qn (inverting) Waveform 1 4.0 2.5 7.0 4.5 10.5 7.5 3.5 2.0 12.0 8.0 ns tPLH tPHL Propagation delay LE to Qn Waveform 3 6.5 6.0 9.5 9.0 13.0 12.5 5.5 5.0 15.0 14.0 ns tPLH tPHL Propagation delay An or Bn to Qn Waveform 1, 2 4.0 4.0 6.5 7.0 9.5 10.5 3.5 3.5 10.5 12.5 ns AC SETUP REQUIREMENTS LIMITS Tamb = +25°C Tamb = 0°C to +70°C SYMBOL PARAMETER TEST VCC = +5.0V VCC = +5.0V ± 10% UNIT CONDITION C D = 50pF, RL = 500Ω C D = 50pF, RL = 500Ω MIN TYP MAX MIN MAX tsu (H) tsu (L) Setup time, high or low An, Bn to LE Waveform 4 0.0 1.0 0.0 3.5 ns th (H) th (L) Hold time, high or low An, Bn to LE Waveform 4 1.5 3.0 2.0 3.5 ns tw (L) LE Pulse width, low Waveform 4 6.5 7.5 ns AC WAVEFORMS VM VM VM VM tPLHtPHL An, Bn, SELCET A/B Qn SF00557 Waveform 1. Propagation delay for SELECT A/B to output (A register stored data = low) or An. Bn to output VM VM VM VM tPLHtPHL An, Bn, SELCET A/B Qn SF00558 Waveform 2. Propagation delay for SELECT A/B to output (A register stored data = low) or An. Bn to output tPHL LE VM VMVM VMVM tPLH Qn SF00559 Waveform 3. Propagation delay for latch enable to output VM VM VM VM VM VM tsu(L) t h(L)tsu(H) t h(H) An, Bn LE SF00560 Waveform 4. Setup time and hold times and LE pulse width Note to AC waveforms For all waveforms, VM = 1.5V. The shaded areas indicate when the input is permitted to change for predictable output performance.
Philips Semiconductors Product specification 74F1604Latch October 4, 1990 6 TEST CIRCUIT AND WAVEFORMS tw 90% VM 10% 90% VM 10% 90% VM 10% 90% VM 10% NEGATIVE PULSE POSITIVE PULSE tw AMP (V) tTHL (tf ) INPUT PULSE REQUIREMENTS rep. rate tw tTLH tTHL 1MHz 500ns 2.5ns 2.5ns Input Pulse Definition VCC family 74F D.U.T.PULSE GENERATOR R LC LR T VIN VOUT Test Circuit for Totem-Pole Outputs DEFINITIONS: R L = Load resistor; see AC ELECTRICAL CHARACTERISTICS for value. C L = Load capacitance includes jig and probe capacitance; see AC ELECTRICAL CHARACTERISTICS for value. R T = Termination resistance should be equal to ZOUT of pulse generators. tTHL (tf ) tTLH (tr ) tTLH (tr ) AMP (V) amplitude 3.0V 1.5V VM SF00006
Philips Semiconductors Product specification 74F1604Latch
1990 Oct 04 7
DIP28: plastic dual in-line package; 28 leads (600 mil); long body SOT117-2
Philips Semiconductors Product specification 74F1604Latch
1990 Oct 04 8
SO28: plastic small outline package; 28 leads; body width 7.5mm SOT136-1
Philips Semiconductors Product specification 74F1604Latch
1990 Oct 04 9
Philips Semiconductors Product specification 74F1604Latch yyyy mmm dd 10 Definitions Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Disclaimers Life support — These products are not designed for use in life support appliances, devices or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes — Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Philips Semiconductors
811 East Arques Avenue
P.O. Box 3409 Sunnyvale, California 94088–3409 Telephone 800-234-7381 Copyright Philips Electronics North America Corporation 1998 All rights reserved. Printed in U.S.A. print code Date of release: 10-98 Document order number: 9397-750-05194 /C0109 /C0110 /C0114 Data sheet status Objective specification Preliminary specification Product specification Product status Development Qualification Production Definition [1] This data sheet contains the design target or goal specifications for product development. Specification may change in any manner without notice. This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips Semiconductors reserves the right to make chages at any time without notice in order to improve design and supply the best possible product. This data sheet contains final specifications. Philips Semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. Data sheet status [1] Please consult the most recently issued datasheet before initiating or completing a design.