74F1245 PHILIPS

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 10

Technical content

Octal transceiver (3-State) Product specification 1995 Mar 01 INTEGRATED CIRCUITS IC15 Data Handbook

Philips Semiconductors Product specification 74F1245Octal transceiver (3-State)

21995 Mar 01 853-0885 14921

FEATURES

  • Same function and pinout as 74F245
  • High impedance NPN base inputs for reduced loading (70µA in Low and High states)
  • Useful in applications where light loading bus loading or direct interface with output of a MOS microprocessor is desired
  • Octal bidirectional bus interface
  • Glitch free during 3-State power up and power down
  • 3-State buffer outputs sink 64mA and source 15mA TYPE TYPICAL PROPAGATION DELAY TYPICAL SUPPLY CURRENT (TOTAL) 74F1245 5.0ns 115mA

DESCRIPTION

The 74F1245 is an octal transceiver featuring non-inverting 3-State bus compatible outputs in both transmit and receive directions. The B port outputs are capable of sinking 64mA and sourcing up to 15mA, producing very good capacitive drive characteristics. The device features an Output Enable (OE ) input for easy cascading and Transmit/Receive (T/R) input for direction control. The 3-State outputs, B0–B7, have been designed to prevent output bus loading if the power is removed from the device.

ORDERING INFORMATION

VCC = 5V ±10%, Tamb = 0°C to +70°C DRAWING NUMBER 20-Pin Plastic DIP N74F1245N SOT146-1 20-Pin Plastic SOL N74F1245D SOT163-1 INPUT AND OUTPUT LOADING AND FAN-OUT TABLE PINS DESCRIPTION 74F (U.L.) HIGH/LOW LOAD VALUE HIGH/LOW A0–A7, B0–B7 A and B port inputs 3.5/0.117 70µA/70µA OE Output Enable input (active Low) 2.0/0.033 40µA/20µA T/R Transmit/Receive input 2.0/0.033 40µA/20µA A0–A7 A port outputs 150/40 3.0mA/24mA B0–B7 B port outputs 750/106.7 15mA/64mA NOTE: One (1.0) FAST unit load is defined as: 20µA in the High state and 0.6mA in the Low state. PIN CONFIGURATION SF00198 10 11 20T/R GND VCC OE LOGIC SYMBOL B2 B3 B4 B5 16 15 14 13 234 VCC = Pin 20 GND = Pin 10 SF00199 OE T/R A0 A1 A2 A3 A4 A5 567 B6 B7 12 11 A6 A7

Philips Semiconductors Product specification 74F1245Octal transceiver (3-State)

1995 Mar 01 3

LOGIC SYMBOL (IEEE/IEC) SF00649 G319 3EN1 (BA) 1 3EN2 (AB) ∇ 1 2 ∇2 FUNCTION TABLE INPUTS INPUTS/OUTPUTS OE T/R An Bn L L A = B INPUTS L H INPUTS B = A H X Z Z H = High voltage level L = Low voltage level X = Don’t care Z = High impedance “off” state LOGIC DIAGRAM SF00201 A0 A1 A2 A3 A4 A5 A6 A7 23456789 OE T/R VCC = Pin 20 GND = Pin 10 ABSOLUTE MAXIMUM RATINGS (Operation beyond the limits set forth in this table may impair the useful life of the device. Unless otherwise noted these limits are over the operating free-air temperature range.) SYMBOL PARAMETER RATING UNIT VCC Supply voltage –0.5 to +7.0 V VIN Input voltage –0.5 to +7.0 V IIN Input current –30 to +5 mA VOUT Voltage applied to output in High output state –0.5 to +5.5 V IO Current applied to output in Low output state A0–A7 48 mA IOUT C urrent applied to output in Low output state B0–B7 128 mA Tamb Operating free-air temperature range 0 to +70 °C Tstg Storage temperature range –65 to +150 °C

Philips Semiconductors Product specification 74F1245Octal transceiver (3-State)

1995 Mar 01 4

RECOMMENDED OPERATING CONDITIONS SYMBOL PARAMETER LIMITS UNITSYMBOL PARAMETER MIN NOM MAX UNIT VCC Supply voltage 4.5 5.0 5.5 V VIH High-level input voltage 2.0 V VIL Low-level input voltage 0.8 V IIK Input clamp current –18 mA IO High level output current A0–A7 –3 mA IOH High-level output current B0–B7 –15 mA IO Low level output current A0–A7 24 mA IOL Low-level output current B0–B7 64 mA Tamb Operating free-air temperature range 0 70 °C DC ELECTRICAL CHARACTERISTICS (Over recommended operating free-air temperature range unless otherwise noted.) NO TAG LIMITS SYMBOL PARAMETER TEST CONDITIONS NO TAG MIN TYP NO TAG MAX UNIT A0–A7 B0–B7 IOH = –3mA ±10% V CC 2.4 V VOH High-level output voltage A0–A7, B0–B7 VCC = MIN, VIL= MAX IOH = –3mA ±5% V CC 2.7 3.3 V VOH High-level out ut voltage B0–B7 VIL = MAX , VIH = MIN IOH = –15mA ±10% V CC 2.0 V B0–B7 IOH = –15mA ±5% V CC 2.0 V A0–A7 IOL = 24mA ±10% V CC 0.35 0.50 V VOL Low-level output voltage A0–A7 VCC = MIN, VIL= MAX IOL = 24mA ±5% V CC 0.35 0.50 V VOL Low -level out ut voltage B0–B7 VIL = MAX , VIH = MIN IOL = 48mA ±10% V CC 0.30 0.55 V B0–B7 IOL = 64mA ±5% V CC 0.42 0.55 V VIK Input clamp voltage VCC = MIN, II = IIK –0.73 –1.2 V II Input current at maximumOE , T/R VCC = 0.0V, VI = 7.0V 100 µA II input voltage A0–A7, B0–B7 VCC = 0.0V, VI = 5.5V 100 µA IIH High-level input currentOE , T/R only VCC = MAX, VI = 2.7V 40 µA IIL Low-level input current OE , T/R only VCC = MAX, VI = 0.5V –20 µA IIH+IOZH Off-state output current High-level voltage applied VCC = MAX, VO = 2.7V 70 µA IIL+IOZL Off-state output current Low-level voltage applied VCC = MAX, VO = 0.5V –70 µA IOS Short-circuit output NO TAG A0–A7 VCC = MAX –60 –150 mA IOS currentNO TAG B0–B7 VCC = MAX –100 –225 mA ICCH 120 155 mA ICC Supply current (total) ICCL VCC = MAX 116 150 mA ICCZ 110 165 mA NOTES: 1. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions for the applicable type. 2. All typical values are at VCC = 5V, Tamb = 25°C. 3. Not more than one output should be shorted at a time. For testing IOS , the use of high-speed test apparatus and/or sample-and-hold techniques are preferable in order to minimize internal heating and more accurately reflect operational values. Otherwise, prolonged shorting of a High output may raise the chip temperature well above normal and thereby cause invalid readings in other parameter tests. In any sequence of parameter tests, IOS tests should be performed last.

Philips Semiconductors Product specification 74F1245Octal transceiver (3-State)

1995 Mar 01 5

AC ELECTRICAL CHARACTERISTICS LIMITS SYMBOL PARAMETER TEST CONDITION VCC = +5.0V Tamb = +25°C C L = 50pF, RL = 500Ω VCC = +5.0V ± 10% Tamb = 0°C to +70°C C L = 50pF, RL = 500Ω UNIT MIN TYP MAX MIN MAX tPLH tPHL Propagation delay An to Bn, Bn to An Waveform NO TAG 2.0 2.5 4.0 5.0 6.5 7.5 1.5 2.0 7.0 8.0 ns tPZH tPZL Output Enable time OE to An or Bn Waveform NO TAG Waveform NO TAG 3.0 4.0 6.0 7.5 8.0 10.0 2.5 3.5 9.0 11.0 ns tPHZ tPLZ Output Disable time OE to An or Bn Waveform NO TAG Waveform NO TAG 2.0 4.0 5.0 7.0 8.0 10.0 1.5 4.0 9.0 11.0 ns AC WAVEFORMS For all waveforms, VM = 1.5V. VMVM VMVM Bn, An An, Bn tPLH tPHL SF00202 Waveform 1. Propagation Delay for Non-Inverting Output VOH –0.3V VM VMVM An, Bn tPZH tPHZ SF00203 OE Waveform 2. 3-State Output Enable Time to High Level and Output Disable Time from High Level VOL +0.3V VM VMVM An, Bn tPZL tPLZ SF00204 OE Waveform 3. 3-State Output Enable Time to Low Level and Output Disable Time from Low Level

Philips Semiconductors Product specification 74F1245Octal transceiver (3-State)

1995 Mar 01 6

TEST CIRCUIT AND WAVEFORMS tw 90% VM 10% 90% VM 10% 90% VM 10% 90% VM 10% NEGATIVE PULSE POSITIVE PULSE tw AMP (V) tTHL (tf ) INPUT PULSE REQUIREMENTS rep. rate tw tTLH tTHL 1MHz 500ns 2.5ns 2.5ns Input Pulse Definition VCC family 74F D.U.T.PULSE GENERATOR R LC LR T VIN VOUT Test Circuit for Open Collector Outputs DEFINITIONS: R L = Load resistor; see AC electrical characteristics for value. C L = Load capacitance includes jig and probe capacitance; see AC electrical characteristics for value. R T = Termination resistance should be equal to ZOUT of pulse generators. tTHL (tf ) tTLH (tr ) tTLH (tr ) AMP (V) amplitude 3.0V 1.5V VM R L 7.0V SF00128 TEST SWITCH tPLZ closed tPZL closed All other open SWITCH POSITION

Philips Semiconductors Product specification 74F1245Octal transceiver (3-State)

1995 Mar 01 7

DIP20: plastic dual in-line package; 20 leads (300 mil) SOT146-1

Philips Semiconductors Product specification 74F1245Octal transceiver (3-State)

1995 Mar 01 8

SO20: plastic small outline package; 20 leads; body width 7.5 mm SOT163-1

Philips Semiconductors Product specification 74F1245Octal transceiver (3-State)

1995 Mar 01 9

Philips Semiconductors Product specification 74F1245Octal transceiver (3-State) Philips Semiconductors and Philips Electronics North America Corporation reserve the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. LIFE SUPPORT APPLICATIONS Philips Semiconductors and Philips Electronics North America Corporation Products are not designed for use in life support appliances, devices, or systems where malfunction of a Philips Semiconductors and Philips Electronics North America Corporation Product can reasonably be expected to result in a personal injury. Philips Semiconductors and Philips Electronics North America Corporation customers using or selling Philips Semiconductors and Philips Electronics North America Corporation Products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors and Philips Electronics North America Corporation for any damages resulting from such improper use or sale. This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips Semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. Philips Semiconductors

811 East Arques Avenue

P.O. Box 3409 Sunnyvale, California 94088–3409 Telephone 800-234-7381 DEFINITIONS Data Sheet Identification Product Status Definition Objective Specification Preliminary Specification Product Specification Formative or in Design Preproduction Product Full Production This data sheet contains the design target or goal specifications for product development. Specifications may change in any manner without notice. This data sheet contains Final Specifications. Philips Semiconductors reserves the right to make changes at any time without notice, in order to improve design and supply the best possible product. Philips Semiconductors and Philips Electronics North America Corporation register eligible circuits under the Semiconductor Chip Protection Act.  Copyright Philips Electronics North America Corporation 1995 All rights reserved. Printed in U.S.A.