DATASHEET SEARCH SITE
Document overview
- Manufacturer or author: Provided By digicamel.com
- PDF pages: 19
Technical content
- General description The 74CBTLVD3861 is a 10-bit 3.3 V to 1.8 V level translating bus switch with one output enable (OE) input. When OE is LOW, the switch is closed and port A is connected to the B port. When OE is HIGH, the switch is disabled. To ensure the high-impedance OFF-state during power-up or power-down, OE should be tied to the VCC through a pull-up resistor. The minimum value of the resistor is determined by the current-sinking capability of the driver. Schmitt trigger action at control input makes the circuit tolerant to slower input rise and fall times across the entire VCC range from 3.0 V to 3.6 V. This device is fully specified for partial power-down applications using IOFF. 2. Features and benefits Supply voltage range from 3.0 V to 3.6 V High noise immunity Complies with JEDEC standard: JESD8-B/JESD36 (3.0 V to 3.6 V) ESD protection: HBM JESD22-A114F exceeds 2000 V CDM AEC-Q100-011 revision B exceeds 1000 V 4 switch connection between two ports 3.3 V to 1.8 V level translation CMOS low power consumption Latch-up performance exceeds 250 mA per JESD78B Class I level A IOFF circuitry provides partial Power-down mode operation Multiple package options Specified from 40 Ct o+ 8 5C and 40 Ct o+ 1 2 5C 74CBTLVD3861 10-bit level-shifting bus switch with output enable Rev. 4 — 14 December 2011 Product data sheet
Table 1. Ordering information
13 B10
Product data sheet Rev. 4 — 14 December 2011 3 of 19 NXP Semiconductors 74CBTLVD3861 10-bit level-shifting bus switch with output enable 5. Pinning information
5.1 Pinning
Fig 3. Pin configuration for TSSOP24 (SOT355-1) F ig 4. Pin configuration for SSOP24 (SOT556-1) 74CBTLVD3861 n.c. VCC A1 OE A2 B1 A3 B2 A4 B3 A5 B4 A6 B5 A7 B6 A8 B7 A9 B8 A10 B9 GND B10 001aan152 74CBTLVD3861 n.c. VCC A1 OE A2 B1 A3 B2 A4 B3 A5 B4 A6 B5 A7 B6 A8 B7 A9 B8 A10 B9 GND B10 001aan153 (1) This is not a supply pin, the substrat e is attached to this pad using conductive die attach material. There is no electrical or mechanical requirement to solder this pad however if it is soldered the solder land should remain floating or be connected to GND. Fig 5. Pin configuration for DHVQFN24 (SOT815-1) 001aan154 74CBTLVD3861 Transparent top view A10 A8 B7 A7 B6 A6 B5 A5 B4 A4 B2 A3 B2 A2 B1 A1 OE GND B10 n.c. VCC 11 14 10 15 9 16 8 17 7 18 6 19 5 20 4 21 3 22 2 23 terminal 1 index area GND(1)
5.2 Pin description
[1] H = HIGH voltage level; L = LOW voltage level; Z = high-impedance OFF-state. [1] The minimum input and output voltage ratings may be exceed ed if the input and output current ratings are observed. [2] For SSOP24 and TSSOP24 packages: P tot derates linearly with 5.5 mW/K above 60 C. For DHVQFN24 package: Ptot derates linearly at 4.5 mW/K above 60 C. Table 2. Pin description Table 3. Function selection [1] Table 4. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V).
- Recommended operating conditions
[1] Applies to control signal levels. [1] All typical values are measured at T amb =2 5 C. [2] One input at 3 V, other inputs at V CC or GND. Table 5. Recommended operating conditions Table 6. Static characteristics At recommended operating conditions voltages are referenced to GND (ground = 0 V).
Product data sheet Rev. 4 — 14 December 2011 6 of 19 NXP Semiconductors 74CBTLVD3861 10-bit level-shifting bus switch with output enable
9.1 Test circuits
9.2 Typical pass voltage graphs
VI = VCC or GND and VO = GND or VCC.V I = VCC or GND and VO = open circuit. Fig 6. Test circuit for measuring OFF-state leakage current (one switch) Fig 7. Test circuit for measuring ON-state leakage current (one switch) 001aan147 GND OE Bn An VCC VIH Is VI VO Is AA 001aan148 GND OE An Bn VCC VIL Is VI VO A Fig 8. Pass voltage versus supply voltage; Tamb = 125 C (typical) Fig 9. Pass voltage versus supply voltage; Tamb =8 5 C (typical) VCC (V) 3.0 3.63.43.2 001aam1021.90 Vpass (V) 1.55 1.60 1.65 1.70 1.75 1.80 1.85 20 μA 100 μA 2 mA 4 mA VCC (V) 3.0 3.63.43.2 001aam1031.90 Vpass (V) 1.55 1.60 1.65 1.70 1.75 1.80 1.85 20 μA 100 μA 2 mA 4 mA
Product data sheet Rev. 4 — 14 December 2011 7 of 19 NXP Semiconductors 74CBTLVD3861 10-bit level-shifting bus switch with output enable Fig 10. Pass voltage versus supply voltage; Tamb =2 5 C (typical) Fig 11. Pass voltage versus supply voltage; Tamb =0 C (typical) VCC (V) 3.0 3.63.43.2 001aam1041.90 Vpass (V) 1.55 1.60 1.65 1.70 1.75 1.80 1.85 20 μA 100 μA 2 mA 4 mA VCC (V) 3.0 3.63.43.2 001aam1051.90 Vpass (V) 1.55 1.60 1.65 1.70 1.75 1.80 1.85 20 μA 100 μA 2 mA 4 mA Fig 12. Pass voltage versus supply voltage; T amb = 40 C (typical) VCC (V) 3.0 3.63.43.2 001aam1061.90 Vpass (V) 1.55 1.60 1.65 1.70 1.75 1.80 1.85 20 μA 100 μA 2 mA 4 mA
9.3 ON resistance
[1] Typical values are measured at T amb =2 5 C and nominal VCC. determined by the lower of the voltages of the two (An or Bn) terminals.
9.4 ON resistance test circuit
Table 7. Resistance R ON At recommended operating conditions; voltages are referenced to GND (ground = 0 V); for test circuit see Figure 13.
[1] All typical values are measured at T amb =2 5 C and at nominal VCC. by an ideal voltage source (zero output impedance). [3] t pd is the same as tPLH and tPHL. [4] t en is the same as tPZH and tPZL. [5] t dis is the same as tPHZ and tPLZ.
10.1 Waveforms
Table 8. Dynamic characteristics Measurement points are given in Table 9. Logic levels: VOL and VOH are typical output voltage levels that occur with the output load. Table 9. Measurement points
Product data sheet Rev. 4 — 14 December 2011 10 of 19 NXP Semiconductors 74CBTLVD3861 10-bit level-shifting bus switch with output enable Measurement points are given in Table 9. Logic levels: VOL and VOH are typical output voltage levels that occur with the output load. Fig 15. Enable and disable times 001aan155 tPLZ tPHZ outputs disabled outputs enabled VY VX outputs enabled output LOW-to-OFF OFF-to-LOW output HIGH-to-OFF OFF-to-HIGH OE input VI VOL VOH 1.8 V VM VM GND GND tPZL tPZH VM VM
Test data is given in Table 10. CL = Load capacitance including jig and probe capacitance. RT = Termination resistance should be equal to the output impedance Zo of the pulse generator. VEXT = External voltage for measuring switching times. Table 10. Test data
10.2 Additional dynami c characteristics
[1] f i is biased at 0.5VCC.
10.3 Test circuit
Table 11. Additional dynamic characteristics Adjust fi voltage to obtain 0 dBm level at output. Increase fi frequency until dB meter reads 3d B .
Product data sheet Rev. 4 — 14 December 2011 13 of 19 NXP Semiconductors 74CBTLVD3861 10-bit level-shifting bus switch with output enable 11. Package outline Fig 18. Package outline SOT556-1 (SSOP24) UNIT A1 A2 A3 HE Lpbp cD (1) E(1) Z(1)eL yw v θ REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA mm 0.25 0.10 1.55 1.40 0.25 0.31 0.20 0.25 0.18 8.8 8.6 4.0 3.8 0.635 1 6.2 5.8 0.89 0.41 1.05 0.66 o o o o 0.180.25 0.1 DIMENSIONS (millimetre dimensions are derived from the original inch dimensions) Note 1. Plastic or metal protrusions of 0.2 mm (0.008 inch) maximum per side are not included. SOT556-1 99-12-27 03-02-18 w M bp D HE E Z e c v M A X A y 1 12 24 13 θ A Lp detail X L (A )3 MO-137 0 2.5 5 mm scale SSOP24: plastic shrink small outline package; 24 leads; body width 3.9 mm; lead pitch 0.635 mm SOT556-1 A max. 1.73 inches 0.0098 0.0040 0.061 0.055 0.01 0.012 0.008 0.0098 0.0075 0.344 0.337 0.157 0.150 0.025 0.0410.244 0.228 0.035 0.016 0.040
Product data sheet Rev. 4 — 14 December 2011 14 of 19 NXP Semiconductors 74CBTLVD3861 10-bit level-shifting bus switch with output enable Fig 19. Package outline SOT355-1 (TSSOP24) UNIT A1 A2 A3 bp cD (1) E(2) (1)eH E LL p QZ y w v θ REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA mm 0.15 0.05 0.95 0.80 0.30 0.19 0.2 0.1 7.9 7.7 4.5 4.3 0.65 6.6 6.2 0.4 0.3 o o0.13 0.10.21 DIMENSIONS (mm are the original dimensions) Notes 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. Plastic interlead protrusions of 0.25 mm maximum per side are not included. 0.75 0.50 SOT355-1 MO-153 99-12-27 03-02-19 0.25 0.5 0.2 w M bp Z e 11 2 24 13 pin 1 index θ AA1 Lp Q detail X L (A )3 HE E c v M A XAD y 0 2.5 5 mm scale TSSOP24: plastic thin shrink small outline package; 24 leads; body width 4.4 mm SOT355-1 A max. 1.1
Product data sheet Rev. 4 — 14 December 2011 15 of 19 NXP Semiconductors 74CBTLVD3861 10-bit level-shifting bus switch with output enable Fig 20. Package outline SOT815-1 (DHVQFN24) REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA Note 1. Plastic or metal protrusions of 0.075 mm maximum per side are not included. SOT815-1 0 2.5 5 mm scale b yy1 C C A C C Bv M w M terminal 1 index area terminal 1 index area X UNIT A(1) max. A1 bc eEh Le1 y w v mm 1 0.05 0.00 0.30 0.18 0.5 4.5 e 1.50.2 2.25 1.95 D h 4.25 3.95 0.05 0.05 y 0.10.1 DIMENSIONS (mm are the original dimensions) 0.5 0.3 D (1) 5.6 5.4 E (1) 3.6 3.4 D E B A e DHVQFN24: plastic dual in-line compatible thermal enhanced very thin quad flat package; no leads; 24 terminals; body 3.5 x 5.5 x 0.85 mm A A1 c detail X Eh L Dh
Table 12. Abbreviations Table 13. Revision history
- Legal pages updated. 74CBTLVD3861 v.3 20111020 Product data sheet - 74CBTLVD3861 v.2 74CBTLVD3861 v.2 20110117 Product data sheet - 74CBTLVD3861 v.1 74CBTLVD3861 v.1 20101206 Product data sheet - -
Product data sheet Rev. 4 — 14 December 2011 17 of 19 NXP Semiconductors 74CBTLVD3861 10-bit level-shifting bus switch with output enable 14. Legal information
14.1 Data sheet status
[1] Please consult the most recently issued document before initiating or completing a design. [2] The term ‘short data sheet’ is explained in section “Definitions”. [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com.
14.2 Definitions
Draft — The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet — A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. Product specification — The information and data provided in a Product data sheet shall define the specification of the product as agreed between NXP Semiconductors and its customer, unless NXP Semiconductors and customer have explicitly agreed otherwise in writing. In no event however, shall an agreement be valid in which the NXP Semiconductors product is deemed to offer functions and qualities beyond those described in the Product data sheet.
14.3 Disclaimers
Limited warranty and liability — Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. In no event shall NXP Semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Notwithstanding any damages that customer might incur for any reason whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of NXP Semiconductors. Right to make changes — NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use — NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors accepts no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk. Applications — Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Customers are responsible for the design and operation of their applications and products using NXP Semiconductors products, and NXP Semiconductors accepts no liability for any assistance with applications or customer product design. It is customer’s sole responsibility to determine whether the NXP Semiconductors product is suitable and fit for the customer’s applications and products planned, as well as for the planned application and use of customer’s third party customer(s). Customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. NXP Semiconductors does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer’s applications or products, or the application or use by customer’s third party customer(s). Customer is responsible for doing all necessary testing for the customer’s applications and products using NXP Semiconductors products in order to avoid a default of the applications and the products or of the application or use by customer’s third party customer(s). NXP does not accept any liability in this respect. Limiting values — Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the device. Limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the Recommended operating conditions section (if present) or the Characteristics sections of this document is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. Terms and conditions of commercial sale — NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms , unless otherwise agreed in a valid written individual agreement. In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. NXP Semiconductors hereby expressly objects to applying the customer’s general terms and conditions with regard to the purchase of NXP Semiconductors products by customer. No offer to sell or license — Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. Export control — This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from competent authorities. Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification.
Product data sheet Rev. 4 — 14 December 2011 18 of 19 NXP Semiconductors 74CBTLVD3861 10-bit level-shifting bus switch with output enable Non-automotive qualified products — Unless this data sheet expressly states that this specific NXP Semiconductors product is automotive qualified, the product is not suitable for automotive use. It is neither qualified nor tested in accordance with automotive testing or application requirements. NXP Semiconductors accepts no liability for inclusion and/or use of non-automotive qualified products in automotive equipment or applications. In the event that customer uses the product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall use the product without NXP Semiconductors’ warranty of the product for such automotive applications, use and specifications, and (b) whenever customer uses the product for automotive applications beyond NXP Semiconductors’ specifications such use shall be solely at customer’s own risk, and (c) customer fully indemnifies NXP Semiconductors for any liability, damages or failed product claims resulting from customer design and use of the product for automotive applications beyond NXP Semiconductors’ standard warranty and NXP Semiconductors’ product specifications.
14.4 Trademarks
Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. 15. Contact information For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com
NXP Semiconductors 74CBTLVD3861 10-bit level-shifting bus switch with output enable © NXP B.V. 2011. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com Date of release: 14 December 2011 Document identifier: 74CBTLVD3861 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section ‘Legal information’. 16. Contents