74AVC8T245 NXP
Document overview
- Manufacturer or author: Provided By digicamel.com
- PDF pages: 23
Technical content
- General description The 74AVC8T245 is an 8-bit, dual supply transceiver that enables bidirectional level translation. It features two data input-output ports (An and Bn), a direction control input (DIR), a output enable input ( OE) and dual supply pins (VCC(A) and VCC(B)). Both VCC(A) and VCC(B) can be supplied at any voltage between 0.8 V and 3.6 V making the device suitable for translating between any of the low voltage nodes (0.8 V, 1.2 V, 1.5 V, 1.8 V, 2.5 V and 3.3 V). Pins An, OE and DIR are referenced to VCC(A) and pins Bn are referenced to VCC(B). A HIGH on DIR allows transmission from An to Bn and a LOW on DIR allows transmission from Bn to An. The output enable input (OE) can be used to disable the outputs so the buses are effectively isolated. The device is fully specified for partial power-down applications using IOFF . The IOFF circuitry disables the output, preventing any damaging backflow current through the device when it is powered down. In suspend mode when either VCC(A) or VCC(B) are at GND level, both An and Bn are in the high-impedance OFF-state. 2. Features n Wide supply voltage range: u VCC(A): 0.8 V to 3.6 V u VCC(B): 0.8 V to 3.6 V n Complies with JEDEC standards: u JESD8-12 (0.8 V to 1.3 V) u JESD8-11 (0.9 V to 1.65 V) u JESD8-7 (1.2 V to 1.95 V) u JESD8-5 (1.8 V to 2.7 V) u JESD8-B (2.7 V to 3.6 V) n ESD protection: u HBM JESD22-A114E Class 3B exceeds 8000 V u MM JESD22-A115-A exceeds 200 V u CDM JESD22-C101C exceeds 1000 V n Maximum data rates: u 380 Mbit/s (≥ 1.8 V to 3.3 V translation) u 260 Mbit/s (≥ 1.1 V to 3.3 V translation) u 260 Mbit/s (≥ 1.1 V to 2.5 V translation) u 210 Mbit/s (≥ 1.1 V to 1.8 V translation) u 150 Mbit/s (≥ 1.1 V to 1.5 V translation) u 100 Mbit/s (≥ 1.1 V to 1.2 V translation) 74AVC8T245 8-bit dual supply translating transceiver with configurable voltage translation; 3-state Rev. 02 — 28 April 2009 Product data sheet
74AVC8T245_2 © NXP B.V. 2009. All rights reserved. Table 1. Ordering information
74AVC8T245_2 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 02 — 28 April 2009 3 of 23 NXP Semiconductors 74AVC8T245 8-bit dual supply translating transceiver; 3-state 5. Pinning information
5.1 Pinning
Fig 2. Logic diagram (one channel) 001aai473 to other seven channels DIR VCC(A) VCC(B) OE (1) The die substrate is attached to this pad using conductive die attach material. It cannot be used as a supply pin or input. Fig 3. Pin configuration TSSOP24 Fig 4. Pin configuration DHVQFN24 74AVC8T245 VCC(A) VCC(B) DIR V CC(B) A1 OE A2 B1 A3 B2 A4 B3 A5 B4 A6 B5 A7 B6 A8 B7 GND B8 GND GND 001aai489 001aai490 74AVC8T245 Transparent top view GND A7 B6 A6 B5 A5 B4 A4 B3 A3 B2 A2 B1 A1 OE DIR V CC(B) GND GND VCC(A) VCC(B) 11 14 10 15 9 16 8 17 7 18 6 19 5 20 4 21 3 22 2 23 terminal 1 index area GND (1)
74AVC8T245_2 © NXP B.V. 2009. All rights reserved.
5.2 Pin description
[1] All GND pins must be connected to ground (0 V). [1] H = HIGH voltage level; L = LOW voltage level; X = don’t care; Z = high-impedance OFF-state. [2] The An, DIR andOE input circuit is referenced to VCC(A); The Bn input circuit is referenced to VCC(B). [3] If at least one of VCC(A) or VCC(B) is at GND level, the device goes into suspend mode. Table 2. Pin description Table 3. Function table[1] Table 4. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V).
74AVC8T245_2 © NXP B.V. 2009. All rights reserved. [1] The minimum input voltage ratings and output voltage ratings may be exceeded if the input and output current ratings are observed. [2] VCCO is the supply voltage associated with the output port. [3] VCCO + 0.5 V should not exceed 4.6 V. [4] For TSSOP24 package: Ptot derates linearly at 5.5 mW/K above 60°C. For DHVQFN24 package: Ptot derates linearly at 4.5 mW/K above 60°C.
- Recommended operating conditions
[1] VCCO is the supply voltage associated with the output port. [2] VCCI is the supply voltage associated with the input port. Table 4. Limiting values …continued In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V). Table 5. Recommended operating conditions Table 6. Typical static characteristics at Tamb = 25°C [1][2] At recommended operating conditions; voltages are referenced to GND (ground = 0 V).
74AVC8T245_2 © NXP B.V. 2009. All rights reserved. [1] VCCO is the supply voltage associated with the output port. [2] VCCI is the supply voltage associated with the data input port. [3] For I/O ports, the parameter IOZ includes the input leakage current. Table 6. Typical static characteristics at Tamb = 25°C [1][2] …continued At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Table 7. Static characteristics[1][2] At recommended operating conditions; voltages are referenced to GND (ground = 0 V).
74AVC8T245_2 © NXP B.V. 2009. All rights reserved. Table 7. Static characteristics …continued[1][2] At recommended operating conditions; voltages are referenced to GND (ground = 0 V).
74AVC8T245_2 © NXP B.V. 2009. All rights reserved. [1] VCCO is the supply voltage associated with the output port. [2] VCCI is the supply voltage associated with the data input port. [3] For I/O ports, the parameter IOZ includes the input leakage current. At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Table 8. Typical total supply current (ICC(A) + ICC(B))
74AVC8T245_2 © NXP B.V. 2009. All rights reserved. [1] tpd is the same as tPLH and tPHL ; tdis is the same as tPLZ and tPHZ ; ten is the same as tPZL and tPZH . [1] tpd is the same as tPLH and tPHL ; tdis is the same as tPLZ and tPHZ ; ten is the same as tPZL and tPZH . Table 9. Typical dynamic characteristics at VCC(A) = 0.8 V and Tamb = 25°C [1] Table 10. Typical dynamic characteristics at VCC(B) = 0.8 V and Tamb = 25°C [1]
74AVC8T245_2 © NXP B.V. 2009. All rights reserved. [1] C PD is used to determine the dynamic power dissipation (PD inµW). L × VCC 2 × fo) = sum of the outputs. Table 11. Typical power dissipation capacitance at VCC(A) = VCC(B) and Tamb = 25°C [1][2] Voltages are referenced to GND (ground=0V ) .
74AVC8T245_2 © NXP B.V. 2009. All rights reserved. [1] tpd is the same as tPLH and tPHL ; tdis is the same as tPLZ and tPHZ ; ten is the same as tPZL and tPZH . Table 12. Dynamic characteristics for temperature range−40 °C to +85°C [1] Voltages are referenced to GND (ground = 0 V); for test circuit seeFigure7; for wave forms seeFigure5 andFigure6.
74AVC8T245_2 © NXP B.V. 2009. All rights reserved. [1] tpd is the same as tPLH and tPHL ; tdis is the same as tPLZ and tPHZ ; ten is the same as tPZL and tPZH . Table 13. Dynamic characteristics for temperature range−40 °C to +125°C [1]
74AVC8T245_2 © NXP B.V. 2009. All rights reserved. [1] VCCI is the supply voltage associated with the data input port. [2] VCCO is the supply voltage associated with the output port. Measurement points are given inTable14. VOL and VOH are typical output voltage levels that occur with the output load. Measurement points are given inTable14. VOL and VOH are typical output voltage levels that occur with the output load. Table 14. Measurement points
74AVC8T245_2 © NXP B.V. 2009. All rights reserved. [1] VCCI is the supply voltage associated with the data input port. [3] VCCO is the supply voltage associated with the output port. Test data is given inTable15. C L = Load capacitance including jig and probe capacitance. R T = Termination resistance. VEXT = External voltage for measuring switching times. Table 15. Test data
74AVC8T245_2 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 02 — 28 April 2009 15 of 23 NXP Semiconductors 74AVC8T245 8-bit dual supply translating transceiver; 3-state 12. Typical propagation delay characteristics a. Propagation delay (An to Bn); VCC(A) = 0.8 V b. Propagation delay (An to Bn); V CC(B) = 0.8 V (1) VCC(B) = 0.8 V. (2) VCC(B) = 1.2 V. (3) VCC(B) = 1.5 V. (4) VCC(B) = 1.8 V. (5) VCC(B) = 2.5 V. (6) VCC(B) = 3.3 V. (1) VCC(A) = 0.8 V. (2) VCC(A) = 1.2 V. (3) VCC(A) = 1.5 V. (4) VCC(A) = 1.8 V. (5) VCC(A) = 2.5 V. (6) VCC(A) = 3.3 V. Fig 8. Typical propagation delay versus load capacitance; Tamb = 25°C 001aai476 C L (pF) 06 0 4020 tpd (ns) (1) (2) (3) (4) (5) (6) C L (pF) 06 0 4020 001aai477 t pd (ns) (1) (2) (3) (4) (5) (6)
74AVC8T245_2 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 02 — 28 April 2009 16 of 23 NXP Semiconductors 74AVC8T245 8-bit dual supply translating transceiver; 3-state a. LOW to HIGH propagation delay (An to Bn); VCC(A) = 1.2 V b. HIGH to LOW propagation delay (An to Bn); VCC(A) = 1.2 V c. LOW to HIGH propagation delay (An to Bn); VCC(A) = 1.5 V d. HIGH to LOW propagation delay (An to Bn); VCC(A) = 1.5 V (1) VCC(B) = 1.2 V. (2) VCC(B) = 1.5 V. (3) VCC(B) = 1.8 V. (4) VCC(B) = 2.5 V. (5) VCC(B) = 3.3 V. Fig 9. Typical propagation delay versus load capacitance; Tamb = 25°C C L (pF) 06 0 4020 001aai478 t PLH (ns) (1) (2) (3) (4) (5) C L (pF) 06 0 4020 001aai491 t PHL (ns) (4) (5) (1) (2) (3) C L (pF) 06 0 4020 001aai479 t PLH (ns) (1) (2) (3) (4) (5) C L (pF) 06 0 4020 001aai480 t PHL (ns) (1) (2) (3) (5) (4)
74AVC8T245_2 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 02 — 28 April 2009 17 of 23 NXP Semiconductors 74AVC8T245 8-bit dual supply translating transceiver; 3-state a. LOW to HIGH propagation delay (An to Bn); VCC(A) = 1.8 V b. HIGH to LOW propagation delay (An to Bn); VCC(A) = 1.8 V c. LOW to HIGH propagation delay (An to Bn); VCC(A) = 2.5 V d. HIGH to LOW propagation delay (An to Bn); VCC(A) = 2.5 V (1) VCC(B) = 1.2 V. (2) VCC(B) = 1.5 V. (3) VCC(B) = 1.8 V. (4) VCC(B) = 2.5 V. (5) VCC(B) = 3.3 V. Fig 10. Typical propagation delay versus load capacitance; Tamb = 25°C C L (pF) 06 0 4020 001aai481 t PLH (ns) (1) (2) (3) (5) (4) C L (pF) 06 0 4020 001aai482 t PHL (ns) (1) (2) (3) (5) (4) C L (pF) 06 0 4020 001aai483 t PLH (ns) (1) (2) (3) (5) (4) C L (pF) 06 0 4020 001aai486 t PHL (ns) (1) (2) (3) (5) (4)
74AVC8T245_2 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 02 — 28 April 2009 18 of 23 NXP Semiconductors 74AVC8T245 8-bit dual supply translating transceiver; 3-state a. LOW to HIGH propagation delay (An to Bn); VCC(A) = 3.3 V b. HIGH to LOW propagation delay (An to Bn); VCC(A) = 3.3 V (1) VCC(B) = 1.2 V. (2) VCC(B) = 1.5 V. (3) VCC(B) = 1.8 V. (4) VCC(B) = 2.5 V. (5) VCC(B) = 3.3 V. Fig 11. Typical propagation delay versus load capacitance; Tamb = 25°C C L (pF) 06 0 4020 001aai485 t PLH (ns) (1) (2) (3) (5) (4) C L (pF) 06 0 4020 001aai484 t PHL (ns) (1) (2) (3) (5) (4)
74AVC8T245_2 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 02 — 28 April 2009 19 of 23 NXP Semiconductors 74AVC8T245 8-bit dual supply translating transceiver; 3-state 13. Package outline Fig 12. Package outline SOT355-1 (TSSOP24) UNIT A 1 A 2 A 3 bp cD (1) E (2) (1)eH E LL p QZ ywv q REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA mm 0.15 0.05 0.95 0.80 0.30 0.19 0.2 0.1 7.9 7.7 4.5 4.3 0.65 6.6 6.2 0.4 0.3 o o0.13 0.10.21 DIMENSIONS (mm are the original dimensions) Notes 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. Plastic interlead protrusions of 0.25 mm maximum per side are not included. 0.75 0.50 SOT355-1 MO-153 99-12-27 03-02-19 0.25 0.5 0.2 w M bp Z e 11 2 24 13 pin 1 index q AA 1 A 2 Lp Q detail X L (A )3 H E E c v M A XAD y 0 2.5 5 mm scale TSSOP24: plastic thin shrink small outline package; 24 leads; body width 4.4 mm SOT355-1 A max. 1.1
74AVC8T245_2 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 02 — 28 April 2009 20 of 23 NXP Semiconductors 74AVC8T245 8-bit dual supply translating transceiver; 3-state Fig 13. Package outline SOT815-1 (DHVQFN24) REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA Note 1. Plastic or metal protrusions of 0.075 mm maximum per side are not included. SOT815-1 0 2.5 5 mm scale b yy1 C C AC C Bv M w M terminal 1 index area terminal 1 index area X UNIT A (1) max. A 1 bc e E h Le1 ywv mm 1 0.05 0.00 0.30 0.18 0.5 4.5 1.50.2 2.25 1.95 D h 4.25 3.95 0.05 0.05 0.10.1 DIMENSIONS (mm are the original dimensions) 0.5 0.3 D (1) 5.6 5.4 E (1) 3.6 3.4 D E B A e DHVQFN24: plastic dual in-line compatible thermal enhanced very thin quad flat package; no leads; 24 terminals; body 3.5 x 5.5 x 0.85 mm A A1 c detail X Eh L D h
74AVC8T245_2 © NXP B.V. 2009. All rights reserved. Table 16. Abbreviations Table 17. Revision history
- Section 5 “Pinning information”: Changed: pin names changed in pin description table. 74AVC8T245_1 20080711 Product data sheet - -
74AVC8T245_2 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 02 — 28 April 2009 22 of 23 NXP Semiconductors 74AVC8T245 8-bit dual supply translating transceiver; 3-state 16. Legal information
16.1 Data sheet status
[1] Please consult the most recently issued document before initiating or completing a design. [2] The term ‘short data sheet’ is explained in section “Definitions”. [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com.
16.2 Definitions
Draft —The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet —A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail.
16.3 Disclaimers
General — Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. Right to make changes —NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use —NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in medical, military, aircraft, space or life support equipment, nor in applications where failure or malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors accepts no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk. Applications —Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Limiting values —Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) may cause permanent damage to the device. Limiting values are stress ratings only and operation of the device at these or any other conditions above those given in the Characteristics sections of this document is not implied. Exposure to limiting values for extended periods may affect device reliability. Terms and conditions of sale —NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms , including those pertaining to warranty, intellectual property rights infringement and limitation of liability, unless explicitly otherwise agreed to in writing by NXP Semiconductors. In case of any inconsistency or conflict between information in this document and such terms and conditions, the latter will prevail. No offer to sell or license —Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. Export control —This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from national authorities.
16.4 Trademarks
Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. 17. Contact information For more information, please visit:http://www.nxp.com For sales office addresses, please send an email to:salesaddresses@nxp.com Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification.
NXP Semiconductors 74AVC8T245 8-bit dual supply translating transceiver; 3-state © NXP B.V. 2009. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com Date of release: 28 April 2009 Document identifier: 74AVC8T245_2 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section ‘Legal information’. 18. Contents 12 Typical propagation delay characteristics. . . 15