DATASHEET SEARCH SITE

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 21

Technical content

  1. General description The 74AUP2G08 provides the dual 2-input AND function. Schmitt-trigger action at all inputs makes the circuit tolerant to slower input rise and fall times across the entire VCC range from 0.8 V to 3.6 V. This device ensures a very low static and dynamic power consumption across the entire VCC range from 0.8 V to 3.6 V. This device is fully specified for partial power-down applications using IOFF. The IOFF circuitry disables the output, preventing a damaging backflow current through the device when it is powered down. 2. Features and benefits  Wide supply voltage range from 0.8 V to 3.6 V  High noise immunity  Complies with JEDEC standards:  JESD8-12 (0.8 V to 1.3 V)  JESD8-11 (0.9 V to 1.65 V)  JESD8-7 (1.2 V to 1.95 V)  JESD8-5 (1.8 V to 2.7 V)  JESD8-B (2.7 V to 3.6 V)  ESD protection:  HBM JESD22-A114F Class 3A exceeds 5000 V  MM JESD22-A115-A exceeds 200 V  CDM JESD22-C101E exceeds 1 000 V  Low static power consumption; ICC = 0.9 A (maximum)  Latch-up performance exceeds 100 mA per JESD78 Class II  Inputs accept voltages up to 3.6 V  Low noise overshoot and undershoot < 10 % of VCC  IOFF circuitry provides partial power-down mode operation  Multiple package options  Specified from 40 Ct o+ 8 5C and 40 Ct o+ 1 2 5C 74AUP2G08 Low-power dual 2-input AND gate Rev. 5 — 1 December 2011 Product data sheet

[1] The pin 1 indicator is located on the lower left corner of the device, below the marking code. Table 1. Ordering information Table 2. Marking codes

6.1 Pinning

6.2 Pin description

Table 3. Pin description

[1] The minimum input and output voltage ratings may be exceed ed if the input and output current ratings are observed. [2] For VSSOP8 packages: above 110 C the value of Ptot derates linearly at 8.0 mW/K. For XSON8, XSON8U and XQFN8U packages: above 118 C the value of Ptot derates linearly with 7.8 mW/K.

  1. Recommended operating conditions

Table 4. Function table [1] Table 5. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V). Table 6. Operating conditions

Table 7. Static characteristics At recommended operating conditions; voltages are referenced to GND (ground = 0 V).

Table 7. Static characteristics …continued At recommended operating conditions; voltages are referenced to GND (ground = 0 V).

[1] One input at V CC  0.6 V, other input at VCC or GND. At recommended operating conditions; voltages are referenced to GND (ground = 0 V).

Table 8. Dynamic characteristics Voltages are referenced to GND (ground = 0 V); for test circuit see Figure 9.

[1] All typical values are measured at nominal V CC. [2] t pd is the same as tPLH and tPHL. [3] C PD is used to determine the dynamic power dissipation (PD in W). (CL  VCC2  fo) = sum of the outputs. Table 8. Dynamic characteristics …continued Voltages are referenced to GND (ground = 0 V); for test circuit see Figure 9. Measurement points are given in Table 9. Logic levels: VOL and VOH are typical output voltage levels that occur with the output load. Table 9. Measurement points

[1] For measuring enable and disable times, R L = 5 k. For measuring propagation delays, set-up and hold times and pulse width, RL =1M . Test data is given in Table 10. CL = Load capacitance including jig and probe capacitance. RT = Termination resistance should be equal to the output impedance Zo of the pulse generator. VEXT = External voltage for measuring switching times. Table 10. Test data

Product data sheet Rev. 5 — 1 December 2011 11 of 21 NXP Semiconductors 74AUP2G08 Low-power dual 2-input AND gate 13. Package outline Fig 10. Package outline SOT765-1 (VSSOP8) UNIT A1 A max. A2 A3 bp L HE Lp wyvce D(1) E(2) Z(1) θ REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA mm 0.15 0.00 0.85 0.60 0.27 0.17 0.23 0.08 2.1 1.9 2.4 2.2 0.5 3.2 3.0 0.4 0.1 0°0.13 0.10.20.4 DIMENSIONS (mm are the original dimensions) Notes 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. Plastic or metal protrusions of 0.25 mm maximum per side are not included. 0.40 0.15 Q 0.21 0.19 SOT765-1 MO-187 02-06-07 w Mbp D Z e 0.12 8 5 θ Q Lp (A3) detail X A L HE E c v M A X A y 2.5 5 mm0 scale VSSOP8: plastic very thin shrink small outline package; 8 leads; body width 2.3 mm SOT765-1 pin 1 index

Product data sheet Rev. 5 — 1 December 2011 12 of 21 NXP Semiconductors 74AUP2G08 Low-power dual 2-input AND gate Fig 11. Package outline SOT833-1 (XSON8) terminal 1 index area REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA SOT833-1 07-11-14 07-12-07 DIMENSIONS (mm are the original dimensions) XSON8: plastic extremely thin small outline package; no leads; 8 terminals; body 1 x 1.95 x 0.5 mm D E e b LL1 e1 e1 0 1 2 mm scale Notes 1. Including plating thickness. 2. Can be visible in some manufacturing processes. UNIT mm 0.25 0.17 2.0 1.9 0.35 0.27 A max b E 1.05 0.95 D ee 1 L 0.40 0.32 L 0.5 0.6 A(1) max 0.5 0.04 (2) (2) A

Product data sheet Rev. 5 — 1 December 2011 13 of 21 NXP Semiconductors 74AUP2G08 Low-power dual 2-input AND gate Fig 12. Package outline SOT1089 (XSON8) ReferencesOutline version European projection Issue date IEC JEDEC JEITA SOT1089 MO-252 sot1089_po 10-04-09 10-04-12 Unit mm max nom min 0.5 0.04 1.40 1.35 1.30 1.05 1.00 0.95 0.55 0.35 0.35 0.30 0.27 A (1) Dimensions Note 1. Including plating thickness. 2. Visible depending upon used manufacturing technology. XSON8: extremely thin small outline package; no leads; 8 terminals; body 1.35 x 1 x 0.5 mm SOT1089 A1 bL 1 0.40 0.35 0.32 0.20 0.15 0.12 DEee 1 L 0 0.5 1 mm scale terminal 1 index area E D detail X A L b e terminal 1 index area (4×)(2) (8×)(2) X

Product data sheet Rev. 5 — 1 December 2011 14 of 21 NXP Semiconductors 74AUP2G08 Low-power dual 2-input AND gate Fig 13. Package outline SOT996-2 (XSON8U) REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA SOT996-2 07-12-18 07-12-21 UNIT A max mm 0.5 0.05 0.00 0.35 0.15 3.1 2.9 0.5 1.5 0.5 0.3 0.6 0.4 0.1 0.05 A DIMENSIONS (mm are the original dimensions) XSON8U: plastic extremely thin small outline package; no leads; 8 terminals; UTLP based; body 3 x 2 x 0.5 mm 0 1 2 mm scale b D 2.1 1.9 E e e1 L L1 0.15 0.05 L2 v w 0.05 y y1 0.1 C yCy1 X b e A CBv M Cw M L terminal 1 index area B AD E detail X A A1

Product data sheet Rev. 5 — 1 December 2011 15 of 21 NXP Semiconductors 74AUP2G08 Low-power dual 2-input AND gate Fig 14. Package outline SOT902-1 (XQFN8U) REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA SOT902-1 05-11-25 07-11-14 UNIT A max mm 0.5 0.25 0.15 0.05 0.00 1.65 1.55 0.35 0.25 0.15 0.05 DIMENSIONS (mm are the original dimensions) XQFN8U: plastic extremely thin quad flat package; no leads; 8 terminals; UTLP based; body 1.6 x 1.6 x 0.5 mm b DL e1 1.65 1.55 e E L1 v 0.10.55 0.5 w 0.05 y 0.05 0.05 0 1 2 mm scale X C yCy1 terminal 1 index area terminal 1 index area B AD E detail X A b ee A CB∅ v M C∅ w M4 L metal area not for soldering

Product data sheet Rev. 5 — 1 December 2011 16 of 21 NXP Semiconductors 74AUP2G08 Low-power dual 2-input AND gate Fig 15. Package outline SOT1116 (XSON8) ReferencesOutline version European projection Issue date IEC JEDEC JEITA SOT1116 sot1116_po 10-04-02 10-04-07 Unit mm max nom min 0.35 0.04 1.25 1.20 1.15 1.05 1.00 0.95 0.55 0.3 0.40 0.35 0.32 A (1) Dimensions Note 1. Including plating thickness. 2. Visible depending upon used manufacturing technology. XSON8: extremely thin small outline package; no leads; 8 terminals; body 1.2 x 1.0 x 0.35 mm SOT1116 A1 b 0.20 0.15 0.12 DEee 1 L 0.35 0.30 0.27 L 0 0.5 1 mm scale terminal 1 index area E D (4×)(2) (8×)(2) A1 A e1 e1 e1 e LL1 b 4 3 2 1 5678

Product data sheet Rev. 5 — 1 December 2011 17 of 21 NXP Semiconductors 74AUP2G08 Low-power dual 2-input AND gate Fig 16. Package outline SOT1203 (XSON8) ReferencesOutline version European projection Issue date IEC JEDEC JEITA SOT1203 sot1203_po 10-04-02 10-04-06 Unit mm max nom min 0.35 0.04 1.40 1.35 1.30 1.05 1.00 0.95 0.55 0.35 0.40 0.35 0.32 A (1) Dimensions Note 1. Including plating thickness. 2. Visible depending upon used manufacturing technology. XSON8: extremely thin small outline package; no leads; 8 terminals; body 1.35 x 1.0 x 0.35 mm SOT1203 A1 b 0.20 0.15 0.12 DEee 1 L 0.35 0.30 0.27 L 0 0.5 1 mm scale terminal 1 index area E D (4×)(2) (8×)(2) AA1 e LL1 b e1 e1 e1

Table 11. Abbreviations Table 12. Revision history

  • Legal pages updated. 74AUP2G08 v.4 20101109 Product data sheet - 74AUP2G08 v.3 74AUP2G08 v.3 20080529 Product data sheet - 74AUP2G08 v.2 74AUP2G08 v.2 20080407 Product data sheet - 74AUP2G08 v.1 74AUP2G08 v.1 20061006 Product data sheet - -

Product data sheet Rev. 5 — 1 December 2011 19 of 21 NXP Semiconductors 74AUP2G08 Low-power dual 2-input AND gate 16. Legal information

16.1 Data sheet status

[1] Please consult the most recently issued document before initiating or completing a design. [2] The term ‘short data sheet’ is explained in section “Definitions”. [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com.

16.2 Definitions

Draft — The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet — A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. Product specification — The information and data provided in a Product data sheet shall define the specification of the product as agreed between NXP Semiconductors and its customer, unless NXP Semiconductors and customer have explicitly agreed otherwise in writing. In no event however, shall an agreement be valid in which the NXP Semiconductors product is deemed to offer functions and qualities beyond those described in the Product data sheet.

16.3 Disclaimers

Limited warranty and liability — Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. In no event shall NXP Semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Notwithstanding any damages that customer might incur for any reason whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of NXP Semiconductors. Right to make changes — NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use — NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors accepts no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk. Applications — Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Customers are responsible for the design and operation of their applications and products using NXP Semiconductors products, and NXP Semiconductors accepts no liability for any assistance with applications or customer product design. It is customer’s sole responsibility to determine whether the NXP Semiconductors product is suitable and fit for the customer’s applications and products planned, as well as for the planned application and use of customer’s third party customer(s). Customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. NXP Semiconductors does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer’s applications or products, or the application or use by customer’s third party customer(s). Customer is responsible for doing all necessary testing for the customer’s applications and products using NXP Semiconductors products in order to avoid a default of the applications and the products or of the application or use by customer’s third party customer(s). NXP does not accept any liability in this respect. Limiting values — Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the device. Limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the Recommended operating conditions section (if present) or the Characteristics sections of this document is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. Terms and conditions of commercial sale — NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms , unless otherwise agreed in a valid written individual agreement. In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. NXP Semiconductors hereby expressly objects to applying the customer’s general terms and conditions with regard to the purchase of NXP Semiconductors products by customer. No offer to sell or license — Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. Export control — This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from competent authorities. Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification.

Product data sheet Rev. 5 — 1 December 2011 20 of 21 NXP Semiconductors 74AUP2G08 Low-power dual 2-input AND gate Non-automotive qualified products — Unless this data sheet expressly states that this specific NXP Semiconductors product is automotive qualified, the product is not suitable for automotive use. It is neither qualified nor tested in accordance with automotive testing or application requirements. NXP Semiconductors accepts no liability for inclusion and/or use of non-automotive qualified products in automotive equipment or applications. In the event that customer uses the product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall use the product without NXP Semiconductors’ warranty of the product for such automotive applications, use and specifications, and (b) whenever customer uses the product for automotive applications beyond NXP Semiconductors’ specifications such use shall be solely at customer’s own risk, and (c) customer fully indemnifies NXP Semiconductors for any liability, damages or failed product claims resulting from customer design and use of the product for automotive applications beyond NXP Semiconductors’ standard warranty and NXP Semiconductors’ product specifications.

16.4 Trademarks

Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. 17. Contact information For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com

NXP Semiconductors 74AUP2G08 Low-power dual 2-input AND gate © NXP B.V. 2011. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com Date of release: 1 December 2011 Document identifier: 74AUP2G08 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section ‘Legal information’. 18. Contents