74AUP2G0604 NEXPERIA
Document overview
- Manufacturer or author: Provided By digicamel.com
- PDF pages: 20
Technical content
- General description The 74AUP2G0604 is a single inverting buffer with open-drain output and a single inverter. It features two input pins (nA), an output pin (2Y) and an open-drain output pin (1Y). Schmitt trigger action at all inputs makes the circuit tolerant of slower input rise and fall times across the entire VCC range from 0.8 V to 3.6 V. This device ensures a very low static and dynamic power consumption across the entire VCC range from 0.8 V to 3.6 V. This device is fully specified for partial power-down applications using IOFF. The IOFF circuitry disables the output, preventing the damaging backflow current through the device when it is powered down. 2. Features and benefits Wide supply voltage range from 0.8 V to 3.6 V High noise immunity Complies with JEDEC standards: JESD8-12 (0.8 V to 1.3 V) JESD8-11 (0.9 V to 1.65 V) JESD8-7 (1.2 V to 1.95 V) JESD8-5 (1.8 V to 2.7 V) JESD8-B (2.7 V to 3.6 V) ESD protection: HBM JESD22-A114F Class 3A exceeds 5000 V MM JESD22-A115-A exceeds 200 V CDM JESD22-C101E exceeds 1000 V Low static power consumption; ICC = 0.9 A (maximum) Latch-up performance exceeds 100 mA per JESD 78 Class II Inputs accept voltages up to 3.6 V Low noise overshoot and undershoot < 10 % of VCC IOFF circuitry provides partial power-down mode operation Multiple package options Specified from 40 Ct o+ 8 5C and 40 Ct o+ 1 2 5C 74AUP2G0604 Low-power inverting buffer with open-drain and inverter Rev. 1 — 23 November 2012 Product data sheet
74AUP2G0604 All information provided in this document is subject to legal disclaimers. [1] The pin 1 indicator is located on the lower left corner of the device, below the marking code. Table 1. Ordering information Table 2. Marking
74AUP2G0604 All information provided in this document is subject to legal disclaimers.
6.1 Pinning
6.2 Pin description
[1] H = HIGH voltage level; L = LOW voltage level. [1] H = HIGH voltage level; L = LOW voltage level. Table 3. Pin description Table 4. Function table [1] Table 5. Function table [1]
74AUP2G0604 All information provided in this document is subject to legal disclaimers. [1] The input and output voltage ratings may be exceeded if the input and output current ratings are observed. [2] For SC-88 packages: above 87.5 C the value of Ptot derates linearly with 4.0 mW/K. For XSON6 packages: above 118 C the value of Ptot derates linearly with 7.8 mW/K.
- Recommended operating conditions
Table 6. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V). Table 7. Recommended operating conditions
74AUP2G0604 All information provided in this document is subject to legal disclaimers. Table 8. Static characteristics At recommended operating conditions; voltages are referenced to GND (ground = 0 V).
74AUP2G0604 All information provided in this document is subject to legal disclaimers. Table 8. Static characteristics …continued At recommended operating conditions; voltages are referenced to GND (ground = 0 V).
74AUP2G0604 All information provided in this document is subject to legal disclaimers. At recommended operating conditions; voltages are referenced to GND (ground = 0 V).
74AUP2G0604 All information provided in this document is subject to legal disclaimers. Table 9. Dynamic characteristics Voltages are referenced to GND (ground = 0 V); for test circuit see Figure 8.
74AUP2G0604 All information provided in this document is subject to legal disclaimers. [1] All typical values are measured at nominal V CC. [2] t pd is the same as tPLH and tPHL(2A to 2Y) and tPLZ and tPZL(1A to 1Y). [3] All specified values are the avera ge typical values over all stated loads. [4] C PD is used to determine the dynamic power dissipation (PD in W). [5] C PD is used to determine the dynamic power dissipation (PD in W). (CL VCC2 fo) = sum of the outputs. Table 9. Dynamic characteristics …continued Voltages are referenced to GND (ground = 0 V); for test circuit see Figure 8.
74AUP2G0604 All information provided in this document is subject to legal disclaimers. Measurement points are given in Table 10. Logic levels: VOL and VOH are typical output voltage levels that occur with the output load. Table 10. Measurement points
74AUP2G0604 All information provided in this document is subject to legal disclaimers. Test data is given in Table 11. CL = Load capacitance including jig and probe capacitance. RT = Termination resistance should be equal to the output impedance Zo of the pulse generator. VEXT = External voltage for measuring switching times. Table 11. Test data
© Nexperia B.V. 2017. All rights reserved 74AUP2G0604 All information provided in this document is subject to legal disclaimers. Product data sheet Rev. 1 — 23 November 2012 12 of 20 Nexperia 74AUP2G0604 Low-power inverting buffer with open-drain and inverter 13. Package outline Fig 9. Package outline SOT363 (SC-88) REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA SOT363 SC-88 wBMbp D e pin 1 index A Lp Q detail X HE E v M A AB y 0 1 2 mm scale c X 13 2 4 56 Plastic surface-mounted package; 6 leads SOT363 UNIT A1 max bp cD E e1 HE Lp Qy w v mm 0.1 0.30 0.20 2.2 1.8 0.25 0.10 1.35 1.15 0.65 e 1.3 2.2 2.0 0.2 0.10.2 DIMENSIONS (mm are the original dimensions) 0.45 0.15 0.25 0.15 A 1.1 0.8 04-11-08 06-03-16
© Nexperia B.V. 2017. All rights reserved 74AUP2G0604 All information provided in this document is subject to legal disclaimers. Product data sheet Rev. 1 — 23 November 2012 13 of 20 Nexperia 74AUP2G0604 Low-power inverting buffer with open-drain and inverter Fig 10. Package outline SOT886 (XSON6) ReferencesOutline version European projection Issue date IEC JEDEC JEITA SOT886 MO-252 sot886_po 04-07-22 12-01-05 Unit mm max nom min 0.5 0.04 1.50 1.45 1.40 1.05 1.00 0.95 0.35 0.30 0.27 0.40 0.35 0.32 0.6 A (1) Dimensions (mm are the original dimensions) Notes 1. Including plating thickness. 2. Can be visible in some manufacturing processes. XSON6: plastic extremely thin small outline package; no leads; 6 terminals; body 1 x 1.45 x 0.5 mm SOT886 A1 b 0.25 0.20 0.17 DEe e 0.5 LL 1 terminal 1 index area D E e b LL1 0 1 2 mm scale (2) (2) A
© Nexperia B.V. 2017. All rights reserved 74AUP2G0604 All information provided in this document is subject to legal disclaimers. Product data sheet Rev. 1 — 23 November 2012 14 of 20 Nexperia 74AUP2G0604 Low-power inverting buffer with open-drain and inverter Fig 11. Package outline SOT891 (XSON6) terminal 1 index area REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA SOT891 SOT891 05-04-06 07-05-15 XSON6: plastic extremely thin small outline package; no leads; 6 terminals; body 1 x 1 x 0.5 mm D E e b LL1 0 1 2 mm scale DIMENSIONS (mm are the original dimensions) UNIT mm 0.20 0.12 1.05 0.95 0.35 0.27 A max b E 1.05 0.95 D ee 1 L 0.40 0.32 L 0.350.55 A max 0.5 0.04 A6× (1) (1) Note 1. Can be visible in some manufacturing processes.
© Nexperia B.V. 2017. All rights reserved 74AUP2G0604 All information provided in this document is subject to legal disclaimers. Product data sheet Rev. 1 — 23 November 2012 15 of 20 Nexperia 74AUP2G0604 Low-power inverting buffer with open-drain and inverter Fig 12. Package outline SOT1115 (XSON6) ReferencesOutline version European projection Issue date IEC JEDEC JEITA SOT1115 sot1115_po 10-04-02 10-04-07 Unit mm max nom min 0.35 0.04 0.95 0.90 0.85 1.05 1.00 0.95 0.55 0.3 0.40 0.35 0.32 A (1) Dimensions Note 1. Including plating thickness. 2. Visible depending upon used manufacturing technology. XSON6: extremely thin small outline package; no leads; 6 terminals; body 0.9 x 1.0 x 0.35 mm SOT1115 A1 b 0.20 0.15 0.12 DEee 1 L 0.35 0.30 0.27 L 0 0.5 1 mm scale terminal 1 index area D E (4×)(2) e1 e1 e LL1 b 3 2 1 6 5 4 (6×)(2) A1 A
© Nexperia B.V. 2017. All rights reserved 74AUP2G0604 All information provided in this document is subject to legal disclaimers. Product data sheet Rev. 1 — 23 November 2012 16 of 20 Nexperia 74AUP2G0604 Low-power inverting buffer with open-drain and inverter Fig 13. Package outline SOT1202 (XSON6) ReferencesOutline version European projection Issue date IEC JEDEC JEITA SOT1202 sot1202_po 10-04-02 10-04-06 Unit mm max nom min 0.35 0.04 1.05 1.00 0.95 1.05 1.00 0.95 0.55 0.35 0.40 0.35 0.32 A (1) Dimensions Note 1. Including plating thickness. 2. Visible depending upon used manufacturing technology. XSON6: extremely thin small outline package; no leads; 6 terminals; body 1.0 x 1.0 x 0.35 mm SOT1202 A1 b 0.20 0.15 0.12 DEee 1 L 0.35 0.30 0.27 L 0 0.5 1 mm scale terminal 1 index area D E (4×)(2) e1 e1 e L b 123 6 5 4 (6×)(2) AA1
74AUP2G0604 All information provided in this document is subject to legal disclaimers. Table 12. Abbreviations Table 13. Revision history
© Nexperia B.V. 2017. All rights reserved 74AUP2G0604 All information provided in this document is subject to legal disclaimers. Product data sheet Rev. 1 — 23 November 2012 18 of 20 Nexperia 74AUP2G0604 Low-power inverting buffer with open-drain and inverter 16. Legal information
16.1 Data sheet status
[1] Please consult the most recently issued document before initiating or completing a design. [2] The term ‘short data sheet’ is explained in section “Definitions”. [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nexperia.com .
16.2 Definitions
Draft — The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. Nexperia does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet — A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request vi a the local Nexperia sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. Product specification — The information and data provided in a Product data sheet shall define the specification of the product as agreed between Nexperia and its customer , unless Nexperia and customer have explicitly agreed otherwise in writing. In no event however, shall an agreement be valid in which the Nexperia product is deemed to offer functions and qualities beyond those described in the Product data sheet.
16.3 Disclaimers
Limited warranty and liability — Information in this document is believed to be accurate and reliable. However, Nexperia does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. Nexperia takes no responsibility for the content in this document if provided by an information source outside of Nexperia. In no event shall Nexperia be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Notwithstanding any damages that customer might incur for any reason whatsoever, Nexperia’s aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of Nexperia. Right to make changes — Nexperia reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use — Nexperia products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or malfunction of a Nexperia product can reasonably be expected to result in personal injury, death or severe property or environmental damage. Nexperia and its suppliers accept no liability for inclusion and/or use of Nexperia products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk. Applications — Applications that are described herein for any of these products are for illustrative purpos es only. Nexperia makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Customers are responsible for the design and operation of their applications and products using Nexperia products, and Nexperia accepts no liability for any assistance with applications or customer product design. It is customer’s sole responsibility to determine whether the Nexperia product is suitable and fit for the customer’s applications and products planned, as well as for the planned application and use of customer’s third party customer(s). Customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. Nexperia does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer’s applications or products, or the application or use by customer’s third party customer(s). Customer is responsible for doing all necessary testing for the customer’s applications and products using Nexperia products in order to av oid a default of the applications and the products or of the application or use by customer’s third party customer(s). Nexperia does not accept any liability in this respect. Limiting values — Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the device. Limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the Recommended operating conditions section (if present) or the Characteristics sections of this document is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. Terms and conditions of commercial sale — Nexperia products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nexperia.com/profile/terms , unless otherwise agreed in a valid written individual agreement. In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. Nexperia hereby expressly objects to applying the customer’s general terms and conditions with regard to the purchase of Nexperia products by customer. No offer to sell or license — Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification.
© Nexperia B.V. 2017. All rights reserved 74AUP2G0604 All information provided in this document is subject to legal disclaimers. Product data sheet Rev. 1 — 23 November 2012 19 of 20 Nexperia 74AUP2G0604 Low-power inverting buffer with open-drain and inverter Export control — This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from competent authorities. Non-automotive qualified products — Unless this data sheet expressly states that this specific Nexperia product is automotive qualified, the product is not suitable for automotive use. It is neither qualified nor tested in accordance with automotive testing or application requirements. Nexperia accepts no liabili ty for inclusion and/or use of non-automotive qualified products in automotive equipment or applications. In the event that customer uses the product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall use the product without Nexperia’s warranty of the product for such automotive applications, use and specifications, and (b) whenever customer uses the product for automotive applications beyond Nexperia’s specifications such use shall be solely at customer’s own risk, and (c) customer fully indemnifies Nexperia for any liability, damages or failed product claims resulting from customer design and use of the product for automotive app lications beyond Nexperia’s standard warranty and Nexperia’s product specifications . Translations — A non-English (translated) version of a document is for reference only. The English version shall prevail in case of any discrepancy between the translated and English versions.
16.4 Trademarks
Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. 17. Contact information For more information, please visit: http://www.nexperia.com For sales office addresses, please send an email to: salesaddresses@nexperia.com
Low-power inverting buffer with open-drain and inverter 18. Contents © Nexperia B.V. 2017. All rights reserved For more information, please visit: http://www.nexperia.com For sales office addresses, please send an email to: salesaddresses@nexperia.com Date of release: