74AUP1G14 NXP
Document overview
- Manufacturer or author: Provided By digicamel.com
- PDF pages: 19
Technical content
- General description The 74AUP1G14 provides a single inverting Schmitt trigger which accepts standard input signals. It is capable of transforming slowly changing input signals into sharply defined, jitter-free output signals. This device ensures a very low static and dynamic power consumption across the entire V CC range from 0.8 V to 3.6 V. This device is fully specified for partial Power-down applications using IOFF . The IOFF circuitry disables the output, preventing the damaging backflow current through the device when it is powered down. The inputs switch at different points for positive and negative-going signals. The difference between the positive voltage VT+ and the negative voltage VT− is defined as the input hysteresis voltage VH . 2. Features n Wide supply voltage range from 0.8 V to 3.6 V n High noise immunity n ESD protection: u HBM JESD22-A114E Class 3A exceeds 5000 V u MM JESD22-A115-A exceeds 200 V u CDM JESD22-C101C exceeds 1000 V n Low static power consumption; ICC = 0.9µA (maximum) n Latch-up performance exceeds 100 mA per JESD 78 Class II n Inputs accept voltages up to 3.6 V n Low noise overshoot and undershoot < 10 % of VCC n IOFF circuitry provides partial Power-down mode operation n Multiple package options n Specified from−40 °Ct o+ 8 5°C and −40 °C to +125°C 3. Applications n Wave and pulse shaper n Astable multivibrator n Monostable multivibrator 74AUP1G14 Low-power Schmitt trigger inverter Rev. 03 — 8 July 2009 Product data sheet
74AUP1G14_3 © NXP B.V. 2009. All rights reserved. [1] The pin 1 indicator is located on the lower left corner of the device, below the marking code. Table 1. Ordering information Table 2. Marking
74AUP1G14_3 © NXP B.V. 2009. All rights reserved.
7.1 Pinning
7.2 Pin description
Table 3. Pin description Table 4. Function table[1]
74AUP1G14_3 © NXP B.V. 2009. All rights reserved. [1] The input and output voltage ratings may be exceeded if the input and output current ratings are observed. [2] For TSSOP5 packages: above 87.5°C the value of Ptotderates linearly with 4.0 mW/K. For XSON6 packages: above 118°C the value of Ptotderates linearly with 7.8 mW/K.
- Recommended operating conditions
Table 5. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V). Table 6. Recommended operating conditions Table 7. Static characteristics At recommended operating conditions; voltages are referenced to GND (ground = 0 V).
74AUP1G14_3 © NXP B.V. 2009. All rights reserved. Table 7. Static characteristics …continued At recommended operating conditions; voltages are referenced to GND (ground = 0 V).
74AUP1G14_3 © NXP B.V. 2009. All rights reserved. At recommended operating conditions; voltages are referenced to GND (ground = 0 V).
74AUP1G14_3 © NXP B.V. 2009. All rights reserved. Table 8. Dynamic characteristics Voltages are referenced to GND (ground = 0 V); for test circuit seeFigure8.
74AUP1G14_3 © NXP B.V. 2009. All rights reserved. [1] All typical values are measured at nominal VCC . [2] tpd is the same as tPLH and tPHL . [3] C PD is used to determine the dynamic power dissipation (PD inµW). L × VCC 2 × fo) = sum of the outputs. Table 8. Dynamic characteristics …continued Voltages are referenced to GND (ground = 0 V); for test circuit seeFigure8. Measurement points are given inTable9. Logic levels: VOL and VOH are typical output voltage levels that occur with the output load. Table 9. Measurement points
74AUP1G14_3 © NXP B.V. 2009. All rights reserved. [1] For measuring enable and disable times RL =5k Ω , for measuring propagation delays, setup and hold times and pulse width RL =1M Ω .
- Transfer characteristics
Test data is given inTable10. C L = Load capacitance including jig and probe capacitance. R T = Termination resistance should be equal to the output impedance Zo of the pulse generator. VEXT = External voltage for measuring switching times. Table 10. Test data Table 11. Transfer characteristics Voltages are referenced to GND (ground = 0 V); for test circuit seeFigure8.
74AUP1G14_3 © NXP B.V. 2009. All rights reserved. Table 11. Transfer characteristics …continued Voltages are referenced to GND (ground = 0 V); for test circuit seeFigure8.
74AUP1G14_3 © NXP B.V. 2009. All rights reserved.
- Waveforms transfer characteristics
Voltages are referenced to GND (ground = 0 V); for test circuit seeFigure8. VT+ and VT− limits at 70 % and 20 %.
74AUP1G14_3 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 03 — 8 July 2009 12 of 19 NXP Semiconductors 74AUP1G14 Low-power Schmitt trigger inverter 16. Application information The slow input rise and fall times cause additional power dissipation, this can be calculated using the following formula: Pad =fi× (tr × ICC(AV) +tf× ICC(AV))× VCC where: Pad = additional power dissipation (µW); fi= input frequency (MHz); tr = input rise time (ns); 10 % to 90 %; tf= input fall time (ns); 90 % to 10 %; ICC(AV) = average additional supply current (µA). Fig 11. Typical transfer characteristics; VCC = 1.8 V VI (V) 001aad691 160 240 I CC (µA) Fig 12. Typical transfer characteristics; VCC = 3.0 V 001aad692 VI (V) 0 3.0 2.01.0 400 800 1200 ICC (µA)
74AUP1G14_3 © NXP B.V. 2009. All rights reserved. Average ICC differs with positive or negative input transitions, as shown inFigure13. An example of a relaxation circuit using the 74AUP1G14 is shown inFigure14. Average values for variable a are given inTable12. Table 12. Variable values
74AUP1G14_3 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 03 — 8 July 2009 14 of 19 NXP Semiconductors 74AUP1G14 Low-power Schmitt trigger inverter 17. Package outline Fig 15. Package outline SOT353-1 (TSSOP5) UNIT A 1 A max. A 2 A 3 bp LH E Lp wyvce D (1) E(1) Z(1) q REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA mm 0.1 1.0 0.8 0.30 0.15 0.25 0.08 2.25 1.85 1.35 1.15 0.65 1.3 2.25 2.0 0.60 0.15 0°0.1 0.10.30.425 DIMENSIONS (mm are the original dimensions) Note 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 0.46 0.21 SOT353-1 MO-203 SC-88A 00-09-01 03-02-19 w Mbp D Z e 0.15 5 4 q AA2 Lp (A3) detail X L H E E c v M A X A y 1.5 3 mm0 scale TSSOP5: plastic thin shrink small outline package; 5 leads; body width 1.25 mm SOT353-1 1.1
74AUP1G14_3 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 03 — 8 July 2009 15 of 19 NXP Semiconductors 74AUP1G14 Low-power Schmitt trigger inverter Fig 16. Package outline SOT886 (XSON6) terminal 1 index area REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA SOT886 MO-252 SOT886 04-07-15 04-07-22 DIMENSIONS (mm are the original dimensions) XSON6: plastic extremely thin small outline package; no leads; 6 terminals; body 1 x 1.45 x 0.5 mm D E e A 1 b LL1 0 1 2 mm scale Notes 1. Including plating thickness. 2. Can be visible in some manufacturing processes. UNIT mm 0.25 0.17 1.5 1.4 0.35 0.27 A max b E 1.05 0.95 D ee 1 L 0.40 0.32 0.50.6 A (1) max 0.5 0.04 (2) (2) A
74AUP1G14_3 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 03 — 8 July 2009 16 of 19 NXP Semiconductors 74AUP1G14 Low-power Schmitt trigger inverter Fig 17. Package outline SOT891 (XSON6) terminal 1 index area REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA SOT891 SOT891 05-04-06 07-05-15 XSON6: plastic extremely thin small outline package; no leads; 6 terminals; body 1 x 1 x 0.5 mm D E e A 1 b LL1 0 1 2 mm scale DIMENSIONS (mm are the original dimensions) UNIT mm 0.20 0.12 1.05 0.95 0.35 0.27 A 1 max b E 1.05 0.95 D ee 1 L 0.40 0.32 0.350.55 A max 0.5 0.04 A6× (1) (1) Note 1. Can be visible in some manufacturing processes.
74AUP1G14_3 © NXP B.V. 2009. All rights reserved. Table 13. Abbreviations Table 14. Revision history
- The format of this data sheet has been redesigned to comply with the new identity guidelines of NXP Semiconductors.
- Legal texts have been adapted to the new company name where appropriate.
- Section 9 “Limiting values”: Changed: Derating factor of XSON6 packages.
- Section 11 “Static characteristics”: Changed: conditions for HIGH-level output voltage and LOW-level output voltage. 74AUP1G14_2 20060828 Product data sheet - 74AUP1G14_1 74AUP1G14_1 20050718 Product data sheet - -
74AUP1G14_3 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 03 — 8 July 2009 18 of 19 NXP Semiconductors 74AUP1G14 Low-power Schmitt trigger inverter 20. Legal information
20.1 Data sheet status
[1] Please consult the most recently issued document before initiating or completing a design. [2] The term ‘short data sheet’ is explained in section “Definitions”. [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com.
20.2 Definitions
Draft —The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet —A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail.
20.3 Disclaimers
General — Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. Right to make changes —NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use —NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in medical, military, aircraft, space or life support equipment, nor in applications where failure or malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors accepts no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk. Applications —Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Limiting values —Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) may cause permanent damage to the device. Limiting values are stress ratings only and operation of the device at these or any other conditions above those given in the Characteristics sections of this document is not implied. Exposure to limiting values for extended periods may affect device reliability. Terms and conditions of sale —NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms , including those pertaining to warranty, intellectual property rights infringement and limitation of liability, unless explicitly otherwise agreed to in writing by NXP Semiconductors. In case of any inconsistency or conflict between information in this document and such terms and conditions, the latter will prevail. No offer to sell or license —Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. Export control —This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from national authorities.
20.4 Trademarks
Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. 21. Contact information For more information, please visit:http://www.nxp.com For sales office addresses, please send an email to:salesaddresses@nxp.com Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification.
NXP Semiconductors 74AUP1G14 Low-power Schmitt trigger inverter © NXP B.V. 2009. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com Date of release: 8 July 2009 Document identifier: 74AUP1G14_3 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section ‘Legal information’. 22. Contents