74AUP1G125 PHILIPS
Document overview
- Manufacturer or author: Provided By digicamel.com
- PDF pages: 21
Technical content
- General description The 74AUP1G125 is a high-performance, low-power, low-voltage, Si-gate CMOS device, superior to most advanced CMOS compatible TTL families. Schmitt-trigger action at all inputs makes the circuit tolerant to slower input rise and fall times across the entire V CC range from 0.8 V to 3.6 V. This device ensures a very low static and dynamic power consumption across the entire VCC range from 0.8 V to 3.6 V. This device is fully specified for partial Power-down applications using IOFF . The IOFF circuitry disables the output, preventing the damaging backflow current through the device when it is powered down. The 74AUP1G125 provides the single non-inverting buffer/line driver with 3-state output. The 3-state output is controlled by the output enable input (OE). A HIGH level at pinOE causes the output to assume a high-impedance OFF-state. This device has the input-disable feature, which allows floating input signals. The inputs are disabled when OE is HIGH. 2. Features n Wide supply voltage range from 0.8 V to 3.6 V n High noise immunity n Complies with JEDEC standards: u JESD8-12 (0.8 V to 1.3 V) u JESD8-11 (0.9 V to 1.65 V) u JESD8-7 (1.2 V to 1.95 V) u JESD8-5 (1.8 V to 2.7 V) u JESD8-B (2.7 V to 3.6 V) n ESD protection: u HBM JESD22-A114-C Class 3A. Exceeds 5000 V u MM JESD22-A115-A exceeds 200 V u CDM JESD22-C101-C exceeds 1000 V n Low static power consumption; ICC = 0.9µA (maximum) n Latch-up performance exceeds 100 mA per JESD 78 Class II n Inputs accept voltages up to 3.6 V n Low noise overshoot and undershoot < 10 % of VCC n Input-disable feature allows floating input conditions n IOFF circuitry provides partial Power-down mode operation n Multiple package options n Specified from−40 °Ct o+ 8 5°C and −40 °C to +125°C 74AUP1G125 Low-power buffer/line driver; 3-state Rev. 02 — 30 June 2006 Product data sheet
74AUP1G125_2 © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 02 — 30 June 2006 2 of 21 Philips Semiconductors 74AUP1G125 Low-power buffer/line driver; 3-state 3. Ordering information 4. Marking 5. Functional diagram Table 1: Ordering information Type number Package Temperature range Name Description Version 74AUP1G125GW −40 °C to +125°C TSSOP5 plastic thin shrink small outline package; 5 leads; body width 1.25 mm SOT353-1 74AUP1G125GM −40 °C to +125°C XSON6 plastic extremely thin small outline package; no leads; 6 terminals; body 1× 1.45× 0.5 mm SOT886 74AUP1G125GF −40 °C to +125°C XSON6 plastic extremely thin small outline package; no leads; 6 terminals; body 1× 1 × 0.5 mm SOT891 Table 2: Marking Type number Marking code 74AUP1G125GW pM 74AUP1G125GM pM 74AUP1G125GF pM Fig 1. Logic symbol Fig 2. IEC logic symbol Fig 3. Logic diagram mna118 AY2 OE mna119 EN 001aad068 A OE Y
74AUP1G125_2 © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 02 — 30 June 2006 3 of 21 Philips Semiconductors 74AUP1G125 Low-power buffer/line driver; 3-state 6. Pinning information
6.1 Pinning
6.2 Pin description
- Functional description [1] H = HIGH voltage level; L = LOW voltage level; X = Don’t care; Z = high-impedance OFF-state. Fig 4. Pin configuration SOT353-1 (TSSOP5) Fig 5. Pin configuration SOT886 (XSON6) Fig 6. Pin configuration SOT891 (XSON6) 74AUP1G125 OE V CC A GND Y 001aab651 74AUP1G125 A 001aab652 OE GND n.c. V CC Y Transparent top view 6 74AUP1G125 A 001aaf014 OE GND n.c. VCC Y Transparent top view Table 3: Pin description Symbol Pin Description TSSOP5 XSON6 OE 1 1 output enable input A 2 2 data input GND 3 3 ground (0 V) Y 4 4 data output n.c. - 5 not connected V CC 5 6 supply voltage Table 4: Function table[1] Input Output OE A Y LLL LH H HXZ
74AUP1G125_2 © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 02 — 30 June 2006 4 of 21 Philips Semiconductors 74AUP1G125 Low-power buffer/line driver; 3-state 8. Limiting values [1] The input and output voltage ratings may be exceeded if the input and output current ratings are observed. [2] For TSSOP5 packages: above 87.5°C the value of Ptotderates linearly with 4.0 mW/K. For XSON6 packages: above 45°C the value of Ptotderates linearly with 2.4 mW/K. 9. Recommended operating conditions Table 5: Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V). Symbol Parameter Conditions Min Max Unit VCC supply voltage −0.5 +4.6 V IIK input clamping current VI<0V - −50 mA VI input voltage [1] −0.5 +4.6 V IOK output clamping current VO >V CC or VO <0V - ±50 mA VO output voltage Active mode [1] −0.5 V CC + 0.5 V Power-down mode [1] −0.5 +4.6 V IO output current V O =0 Vt oVCC - ±20 mA ICC supply current - +50 mA IGND ground current - −50 mA Tstg storage temperature −65 +150 °C Ptot total power dissipation Tamb = −40 °C to +125°C [2] - 250 mW Table 6: Recommended operating conditions Symbol Parameter Conditions Min Max Unit VCC supply voltage 0.8 3.6 V VI input voltage 0 3.6 V VO output voltage Active mode 0 V CC V Power-down mode; VCC = 0 V 0 3.6 V Tamb ambient temperature −40 +125 °C Δt/ΔV input transition rise and fall rate VCC = 0.8 V to 3.6 V 0 200 ns/V
74AUP1G125_2 © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 02 — 30 June 2006 5 of 21 Philips Semiconductors 74AUP1G125 Low-power buffer/line driver; 3-state 10. Static characteristics Table 7: Static characteristics At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Symbol Parameter Conditions Min Typ Max Unit Tamb = 25°C VIH HIGH-state input voltage VCC = 0.8 V 0.70 × VCC -- V VCC = 0.9 V to 1.95 V 0.65 × VCC -- V VCC = 2.3 V to 2.7 V 1.6 - - V VCC = 3.0 V to 3.6 V 2.0 - - V VIL LOW-state input voltage VCC = 0.8 V - - 0.30 × VCC V VCC = 0.9 V to 1.95 V - - 0.35 × VCC V VCC = 2.3 V to 2.7 V - - 0.7 V VCC = 3.0 V to 3.6 V - - 0.9 V VOH HIGH-state output voltage VI = VIH or VIL IO =−20 µA; VCC = 0.8 V to 3.6 V V CC − 0.1 - - V IO =−1.1 mA; VCC = 1.1 V 0.75 × VCC -- V IO =−1.7 mA; VCC = 1.4 V 1.11 - - V IO =−1.9 mA; VCC = 1.65 V 1.32 - - V IO =−2.3 mA; VCC = 2.3 V 2.05 - - V IO =−3.1 mA; VCC = 2.3 V 1.9 - - V IO =−2.7 mA; VCC = 3.0 V 2.72 - - V IO =−4.0 mA; VCC = 3.0 V 2.6 - - V VOL LOW-state output voltage VI = VIH or VIL IO = 20µA; VCC = 0.8 V to 3.6 V - - 0.1 V IO = 1.1 mA; VCC = 1.1 V - - 0.3 × VCC V IO = 1.7 mA; VCC = 1.4 V - - 0.31 V IO = 1.9 mA; VCC = 1.65 V - - 0.31 V IO = 2.3 mA; VCC = 2.3 V - - 0.31 V IO = 3.1 mA; VCC = 2.3 V - - 0.44 V IO = 2.7 mA; VCC = 3.0 V - - 0.31 V IO = 4.0 mA; VCC = 3.0 V - - 0.44 V II input leakage current V I= GND to 3.6 V; VCC = 0 V to 3.6 V - - ±0.1 µA IOZ 3-state output OFF-state current VI = VIH or VIL; VO = 0 V to 3.6 V; VCC = 0 V to 3.6 V -- ±0.1 µA IOFF power-off leakage current VI or VO = 0 V to 3.6 V; VCC = 0 V - - ±0.2 µA ΔIOFF additional power-off leakage current VI or VO = 0 V to 3.6 V; VCC = 0 V to 0.2 V -- ±0.2 µA ICC supply current V I = GND or VCC ; IO =0A ; VCC = 0.8 V to 3.6 V - - 0.5 µA
74AUP1G125_2 © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 02 — 30 June 2006 6 of 21 Philips Semiconductors 74AUP1G125 Low-power buffer/line driver; 3-state ΔICC additional supply current data input; VI=V CC − 0.6 V; IO =0A ; VCC = 3.3 V [1] -- 4 0 µA OE input; VI = VCC − 0.6 V; IO = 0 A; VCC = 3.3 V [1] - - 110 µA all inputs; VI = GND to 3.6 V; OE = VCC ; VCC = 0.8 V to 3.6 V [2] -- 1 µA C I input capacitance V CC = 0 V to 3.6 V; VI = GND or VCC - 0.9 - pF C O output capacitance output enabled V O = GND; VCC = 0 V - 1.7 - pF output disabled V CC = 0 V to 3.6 V; VO = GND or VCC - 1.5 - pF Tamb =−40 °C to +85°C VIH HIGH-state input voltage VCC = 0.8 V 0.70 × VCC -- V VCC = 0.9 V to 1.95 V 0.65 × VCC -- V VCC = 2.3 V to 2.7 V 1.6 - - V VCC = 3.0 V to 3.6 V 2.0 - - V VIL LOW-state input voltage VCC = 0.8 V - - 0.30 × VCC V VCC = 0.9 V to 1.95 V - - 0.35 × VCC V VCC = 2.3 V to 2.7 V - - 0.7 V VCC = 3.0 V to 3.6 V - - 0.9 V VOH HIGH-state output voltage VI = VIH or VIL IO =−20 µA; VCC = 0.8 V to 3.6 V V CC − 0.1 - - V IO =−1.1 mA; VCC = 1.1 V 0.7 × VCC -- V IO =−1.7 mA; VCC = 1.4 V 1.03 - - V IO =−1.9 mA; VCC = 1.65 V 1.30 - - V IO =−2.3 mA; VCC = 2.3 V 1.97 - - V IO =−3.1 mA; VCC = 2.3 V 1.85 - - V IO =−2.7 mA; VCC = 3.0 V 2.67 - - V IO =−4.0 mA; VCC = 3.0 V 2.55 - - V VOL LOW-state output voltage VI = VIH or VIL IO = 20µA; VCC = 0.8 V to 3.6 V - - 0.1 V IO = 1.1 mA; VCC = 1.1 V - - 0.3 × VCC V IO = 1.7 mA; VCC = 1.4 V - - 0.37 V IO = 1.9 mA; VCC = 1.65 V - - 0.35 V IO = 2.3 mA; VCC = 2.3 V - - 0.33 V IO = 3.1 mA; VCC = 2.3 V - - 0.45 V IO = 2.7 mA; VCC = 3.0 V - - 0.33 V IO = 4.0 mA; VCC = 3.0 V - - 0.45 V II input leakage current V I= GND to 3.6 V; VCC = 0 V to 3.6 V - - ±0.5 µA IOZ 3-state output OFF-state current VI = VIH or VIL; VO = 0 V to 3.6 V; VCC = 0 V to 3.6 V -- ±0.5 µA IOFF power-off leakage current VI or VO = 0 V to 3.6 V; VCC = 0 V - - ±0.5 µA Table 7: Static characteristics …continued At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Symbol Parameter Conditions Min Typ Max Unit
74AUP1G125_2 © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 02 — 30 June 2006 7 of 21 Philips Semiconductors 74AUP1G125 Low-power buffer/line driver; 3-state ΔIOFF additional power-off leakage current VI or VO = 0 V to 3.6 V; VCC = 0 V to 0.2 V -- ±0.6 µA ICC supply current V I = GND or VCC ; IO =0A ; VCC = 0.8 V to 3.6 V - - 0.9 µA ΔICC additional supply current data input; VI=V CC − 0.6 V; IO =0A ; VCC = 3.3 V [1] -- 5 0 µA OE input; VI = VCC − 0.6 V; IO = 0 A; VCC = 3.3 V [1] - - 120 µA all inputs; VI = GND to 3.6 V; OE = VCC ; VCC = 0.8 V to 3.6 V [2] -- 1 µA Tamb =−40 °C to +125°C VIH HIGH-state input voltage VCC = 0.8 V 0.75 × VCC -- V VCC = 0.9 V to 1.95 V 0.70 × VCC -- V VCC = 2.3 V to 2.7 V 1.6 - - V VCC = 3.0 V to 3.6 V 2.0 - - V VIL LOW-state input voltage VCC = 0.8 V - - 0.25 × VCC V VCC = 0.9 V to 1.95 V - - 0.30 × VCC V VCC = 2.3 V to 2.7 V - - 0.7 V VCC = 3.0 V to 3.6 V - - 0.9 V VOH HIGH-state output voltage VI = VIH or VIL IO =−20 µA; VCC = 0.8 V to 3.6 V V CC − 0.11 - - V IO =−1.1 mA; VCC = 1.1 V 0.6 × VCC -- V IO =−1.7 mA; VCC = 1.4 V 0.93 - - V IO =−1.9 mA; VCC = 1.65 V 1.17 - - V IO =−2.3 mA; VCC = 2.3 V 1.77 - - V IO =−3.1 mA; VCC = 2.3 V 1.67 - - V IO =−2.7 mA; VCC = 3.0 V 2.40 - - V IO =−4.0 mA; VCC = 3.0 V 2.30 - - V VOL LOW-state output voltage VI = VIH or VIL IO = 20µA; VCC = 0.8 V to 3.6 V - - 0.11 V IO = 1.1 mA; VCC = 1.1 V - - 0.33 × VCC V IO = 1.7 mA; VCC = 1.4 V - - 0.41 V IO = 1.9 mA; VCC = 1.65 V - - 0.39 V IO = 2.3 mA; VCC = 2.3 V - - 0.36 V IO = 3.1 mA; VCC = 2.3 V - - 0.50 V IO = 2.7 mA; VCC = 3.0 V - - 0.36 V IO = 4.0 mA; VCC = 3.0 V - - 0.50 V II input leakage current V I= GND to 3.6 V; VCC = 0 V to 3.6 V - - ±0.75 µA IOZ 3-state output OFF-state current VI = VIH or VIL; VO = 0 V to 3.6 V; VCC = 0 V to 3.6 V -- ±0.75 µA IOFF power-off leakage current VI or VO = 0 V to 3.6 V; VCC = 0 V - - ±0.75 µA Table 7: Static characteristics …continued At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Symbol Parameter Conditions Min Typ Max Unit
74AUP1G125_2 © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 02 — 30 June 2006 8 of 21 Philips Semiconductors 74AUP1G125 Low-power buffer/line driver; 3-state [1] One input at VCC − 0.6 V, other input at VCC or GND. [2] To show ICC remains very low when the input-disable feature is enabled. 11. Dynamic characteristics ΔIOFF additional power-off leakage current VI or VO = 0 V to 3.6 V; VCC = 0 V to 0.2 V -- ±0.75 µA ICC supply current V I = GND or VCC ; IO =0A ; VCC = 0.8 V to 3.6 V - - 1.4 µA ΔICC additional supply current data input; VI=V CC − 0.6 V; IO =0A ; VCC = 3.3 V [1] -- 7 5 µA OE input; VI = VCC − 0.6 V; IO = 0 A; VCC = 3.3 V [1] - - 180 µA all inputs; VI = GND to 3.6 V; OE = VCC ; VCC = 0.8 V to 3.6 V [2] -- 1 µA Table 7: Static characteristics …continued At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Symbol Parameter Conditions Min Typ Max Unit Table 8: Dynamic characteristics Voltages are referenced to GND (ground = 0 V); for test circuit seeFigure9 Symbol Parameter Conditions Min Typ [1] Max Unit Tamb = 25°C; CL = 5 pF tPHL , tPLH HIGH-to-LOW and LOW-to-HIGH propagation delay A to Y see Figure7 VCC = 0.8 V - 20.6 - ns tPZH , tPZL OFF-state to HIGH and OFF-state to LOW propagation delay OE to Y see Figure8 VCC = 0.8 V - 69.9 - ns tPHZ , tPLZ HIGH to OFF-state and LOW to OFF-state propagation delay OE to Y see Figure8 VCC = 0.8 V - 14.3 - ns
74AUP1G125_2 © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 02 — 30 June 2006 9 of 21 Philips Semiconductors 74AUP1G125 Low-power buffer/line driver; 3-state Tamb = 25°C; CL = 10 pF tPHL , tPLH HIGH-to-LOW and LOW-to-HIGH propagation delay A to Y see Figure7 VCC = 0.8 V - 24.0 - ns tPZH , tPZL OFF-state to HIGH and OFF-state to LOW propagation delay OE to Y see Figure8 VCC = 0.8 V - 73.7 - ns tPHZ , tPLZ HIGH to OFF-state and LOW to OFF-state propagation delay OE to Y see Figure8 VCC = 0.8 V - 32.7 - ns Tamb = 25°C; CL = 15 pF tPHL , tPLH HIGH-to-LOW and LOW-to-HIGH propagation delay A to Y see Figure7 VCC = 0.8 V - 27.4 - ns tPZH , tPZL OFF-state to HIGH and OFF-state to LOW propagation delay OE to Y see Figure8 VCC = 0.8 V - 77.5 - ns Table 8: Dynamic characteristics …continued Voltages are referenced to GND (ground = 0 V); for test circuit seeFigure9 Symbol Parameter Conditions Min Typ [1] Max Unit
74AUP1G125_2 © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 02 — 30 June 2006 10 of 21 Philips Semiconductors 74AUP1G125 Low-power buffer/line driver; 3-state tPHZ , tPLZ HIGH to OFF-state and LOW to OFF-state propagation delay OE to Y see Figure8 VCC = 0.8 V - 60.8 - ns Tamb = 25°C; CL = 30 pF tPHL , tPLH HIGH-to-LOW and LOW-to-HIGH propagation delay A to Y see Figure7 VCC = 0.8 V - 37.4 - ns tPZH , tPZL OFF-state to HIGH and OFF-state to LOW propagation delay OE to Y see Figure8 VCC = 0.8 V - 88.9 - ns tPHZ , tPLZ HIGH to OFF-state and LOW to OFF-state propagation delay OE to Y see Figure8 VCC = 0.8 V - 49.9 - ns Table 8: Dynamic characteristics …continued Voltages are referenced to GND (ground = 0 V); for test circuit seeFigure9 Symbol Parameter Conditions Min Typ [1] Max Unit
74AUP1G125_2 © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 02 — 30 June 2006 11 of 21 Philips Semiconductors 74AUP1G125 Low-power buffer/line driver; 3-state [1] All typical values are measured at nominal VCC . [2] C PD is used to determine the dynamic power dissipation (PD inµW). PD =C PD × VCC 2 × fi× N+ Σ(CL × VCC 2 × fo) where: fi= input frequency in MHz; fo = output frequency in MHz; C L = output load capacitance in pF; VCC = supply voltage in V; N = number of inputs switching; Σ(C L × VCC 2 × fo) = sum of the outputs. Tamb = 25°C C PD power dissipation capacitance f = 1 MHz; VI= GND to VCC [2] output enabled VCC = 0.8 V - 2.7 - pF VCC = 1.1 V to 1.3 V - 2.8 - pF VCC = 1.4 V to 1.6 V - 2.9 - pF VCC = 1.65 V to 1.95 V - 3.0 - pF VCC = 2.3 V to 2.7 V - 3.6 - pF VCC = 3.0 V to 3.6 V - 4.2 - pF Table 8: Dynamic characteristics …continued Voltages are referenced to GND (ground = 0 V); for test circuit seeFigure9 Symbol Parameter Conditions Min Typ [1] Max Unit Table 9: Dynamic characteristics Voltages are referenced to GND (ground = 0 V); for test circuit seeFigure9 Symbol Parameter Conditions −40 °C to +85°C −40 °C to +125°C Unit Min Max Min Max C L = 5 pF tPHL , tPLH HIGH-to-LOW and LOW-to-HIGH propagation delay At oY see Figure7 tPZH , tPZL OFF-state to HIGH and OFF-state to LOW propagation delay OE to Y see Figure8 tPHZ , tPLZ HIGH to OFF-state and LOW to OFF-state propagation delay OE to Y see Figure8
74AUP1G125_2 © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 02 — 30 June 2006 12 of 21 Philips Semiconductors 74AUP1G125 Low-power buffer/line driver; 3-state C L = 10 pF tPHL , tPLH HIGH-to-LOW and LOW-to-HIGH propagation delay At oY see Figure7 tPZH , tPZL OFF-state to HIGH and OFF-state to LOW propagation delay OE to Y see Figure8 tPHZ , tPLZ HIGH to OFF-state and LOW to OFF-state propagation delay OE to Y see Figure8 C L = 15 pF tPHL , tPLH HIGH-to-LOW and LOW-to-HIGH propagation delay At oY see Figure7 tPZH , tPZL OFF-state to HIGH and OFF-state to LOW propagation delay OE to Y see Figure8 tPHZ , tPLZ HIGH to OFF-state and LOW to OFF-state propagation delay OE to Y see Figure8 Table 9: Dynamic characteristics …continued Voltages are referenced to GND (ground = 0 V); for test circuit seeFigure9 Symbol Parameter Conditions −40 °C to +85°C −40 °C to +125°C Unit Min Max Min Max
74AUP1G125_2 © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 02 — 30 June 2006 13 of 21 Philips Semiconductors 74AUP1G125 Low-power buffer/line driver; 3-state 12. Waveforms C L = 30 pF tPHL , tPLH HIGH-to-LOW and LOW-to-HIGH propagation delay At oY see Figure7 tPZH , tPZL OFF-state to HIGH and OFF-state to LOW propagation delay OE to Y see Figure8 tPHZ , tPLZ HIGH to OFF-state and LOW to OFF-state propagation delay OE to Y see Figure8 Table 9: Dynamic characteristics …continued Voltages are referenced to GND (ground = 0 V); for test circuit seeFigure9 Symbol Parameter Conditions −40 °C to +85°C −40 °C to +125°C Unit Min Max Min Max Measurement points are given inTable10. Logic levels: VOL and VOH are typical output voltage drops that occur with the output load. Fig 7. The data input (A) to output (Y) propagation delays 001aad070 A input Y output tPLHtPHL GND VI VM VM Table 10: Measurement points Supply voltage Output Input VCC VM VM VI tr = tf
74AUP1G125_2 © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 02 — 30 June 2006 14 of 21 Philips Semiconductors 74AUP1G125 Low-power buffer/line driver; 3-state Measurement points are given inTable11. Logic levels: VOL and VOH are typical output voltage drops that occur with the output load. Fig 8. Turn-on and turn-off times mna644 tPLZ tPHZ outputs disabled outputs enabled VY VX outputs enabled output LOW-to-OFF OFF-to-LOW output HIGH-to-OFF OFF-to-HIGH OE input VI VOL VOH VCC VM GND GND tPZL tPZH VM VM Table 11: Measurement points Supply voltage Input Output VCC VM VM VX VY
74AUP1G125_2 © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 02 — 30 June 2006 15 of 21 Philips Semiconductors 74AUP1G125 Low-power buffer/line driver; 3-state [1] For measuring enable and disable times RL =5k Ω , for measuring propagation delays, setup and hold times and pulse width RL =1M Ω . Test data is given inTable12. Definitions for test circuit: R L = Load resistance. C L = Load capacitance including jig and probe capacitance. R T = Termination resistance should be equal to the output impedance Zo of the pulse generator. VEXT = External voltage for measuring switching times. Fig 9. Load circuitry for switching times 001aac521 PULSE GENERATOR DUT R T VI VO VEXTVCC R L 5 kΩ C L Table 12: Test data Supply voltage Load VEXT VCC C L R L [1] tPLH , tPHL tPZH , tPHZ tPZL , tPLZ 0.8 V to 3.6 V 5 pF , 10 pF , 15 pF and 30 pF 5 kΩ or 1 MΩ open GND 2 × VCC
74AUP1G125_2 © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 02 — 30 June 2006 16 of 21 Philips Semiconductors 74AUP1G125 Low-power buffer/line driver; 3-state 13. Package outline Fig 10. Package outline SOT353-1 (TSSOP5) UNIT A 1 A max. A 2 A 3 bp LH E Lp wyvce D (1) E(1) Z(1) q REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA mm 0.1 1.0 0.8 0.30 0.15 0.25 0.08 2.25 1.85 1.35 1.15 0.65 1.3 2.25 2.0 0.60 0.15 0°0.1 0.10.30.425 DIMENSIONS (mm are the original dimensions) Note 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 0.46 0.21 SOT353-1 MO-203 SC-88A 00-09-01 03-02-19 w Mbp D Z e 0.15 5 4 q AA2 Lp (A3) detail X L H E E c v M A X A y 1.5 3 mm0 scale TSSOP5: plastic thin shrink small outline package; 5 leads; body width 1.25 mm SOT353-1 1.1
74AUP1G125_2 © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 02 — 30 June 2006 17 of 21 Philips Semiconductors 74AUP1G125 Low-power buffer/line driver; 3-state Fig 11. Package outline SOT886 (XSON6) terminal 1 index area REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA SOT886 MO-252 SOT886 04-07-15 04-07-22 DIMENSIONS (mm are the original dimensions) XSON6: plastic extremely thin small outline package; no leads; 6 terminals; body 1 x 1.45 x 0.5 mm D E e A 1 b LL1 0 1 2 mm scale Notes 1. Including plating thickness. 2. Can be visible in some manufacturing processes. UNIT mm 0.25 0.17 1.5 1.4 0.35 0.27 A max b E 1.05 0.95 D ee 1 L 0.40 0.32 0.50.6 A (1) max 0.5 0.04 (2) (2) A
74AUP1G125_2 © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 02 — 30 June 2006 18 of 21 Philips Semiconductors 74AUP1G125 Low-power buffer/line driver; 3-state Fig 12. Package outline SOT891 (XSON6) terminal 1 index area REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA SOT891 SOT891 05-03-11 05-04-06 XSON6: plastic extremely thin small outline package; no leads; 6 terminals; body 1 x 1 x 0.5 mm D E e A 1 b LL1 0 1 2 mm scale DIMENSIONS (mm are the original dimensions) UNIT mm 0.20 0.12 1.05 0.95 0.35 0.27 A 1 max b E 1.05 0.95 D ee 1 L 0.40 0.32 0.350.55 A max 0.5 0.04 A
74AUP1G125_2 © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 02 — 30 June 2006 19 of 21 Philips Semiconductors 74AUP1G125 Low-power buffer/line driver; 3-state 14. Abbreviations 15. Revision history Table 13: Abbreviations Acronym Description CDM Charged Device Model CMOS Complementary Metal Oxide Semiconductor DUT Device Under Test ESD ElectroStatic Discharge HBM Human Body Model MM Machine Model TTL Transistor Transistor Logic Table 14: Revision history Document ID Release date Data sheet status Change notice Supersedes 74AUP1G125_2 20060630 Product data sheet - 74AUP1G125_1 Modifications: • ESD HBM and C PD values modified inSection2,Table8
- Added type number 74AUP1G125GF (XSON6/SOT891) package 74AUP1G125_1 20050718 Product data sheet - -
74AUP1G125_2 © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 02 — 30 June 2006 20 of 21 Philips Semiconductors 74AUP1G125 Low-power buffer/line driver; 3-state 16. Legal information
16.1 Data sheet status
[1] Please consult the most recently issued document before initiating or completing a design. [2] The term ‘short data sheet’ is explained in section “Definitions”. [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.semiconductors.philips.com.
16.2 Definitions
Draft —The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. Philips Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet —A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local Philips Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail.
16.3 Disclaimers
General — Information in this document is believed to be accurate and reliable. However, Philips Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. Right to make changes —Philips Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use —Philips Semiconductors products are not designed, authorized or warranted to be suitable for use in medical, military, aircraft, space or life support equipment, nor in applications where failure or malfunction of a Philips Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. Philips Semiconductors accepts no liability for inclusion and/or use of Philips Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk. Applications —Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Limiting values —Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) may cause permanent damage to the device. Limiting values are stress ratings only and operation of the device at these or any other conditions above those given in the Characteristics sections of this document is not implied. Exposure to limiting values for extended periods may affect device reliability. Terms and conditions of sale —Philips Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.semiconductors.philips.com/profile/terms , including those pertaining to warranty, intellectual property rights infringement and limitation of liability, unless explicitly otherwise agreed to in writing by Philips Semiconductors. In case of any inconsistency or conflict between information in this document and such terms and conditions, the latter will prevail. No offer to sell or license —Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights.
16.4 Trademarks
Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. 17. Contact information For additional information, please visit: http://www.semiconductors.philips.com For sales office addresses, send an email to: sales.addresses@www.semiconductors.philips.com Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification.
Philips Semiconductors 74AUP1G125 Low-power buffer/line driver; 3-state © Koninklijke Philips Electronics N.V. 2006. All rights reserved. For more information, please visit: http://www.semiconductors.philips.com. Date of release: 30 June 2006 Document identifier: 74AUP1G125_2 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section ‘Legal information’. 18. Contents