74ALVCHS162830 PHILIPS

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 10

Technical content

/C0080 /C0115 /C0111/C0110/C0111 /C0115 74ALVCHS162830 18-bit to 36-bit address driver with bus hold (3-State) Product data 2001 Sep 07 INTEGRATED CIRCUITS File under Integrated Circuits — ICL03

Philips Semiconductors Product data 74ALVCHS16283018-bit to 36-bit address driver with bus hold (3-State)

22001 Sep 07 853-2279 27052

FEATURES

  • Output ports have equivalent 26 Ω series resistors, so no external resistors are required
  • Diodes on inputs clamp overshoot
  • ESD classification testing is done to JEDEC Standard JESD22. Protection exceeds 2000 V HBM per method A114.
  • Latch-up testing is done to JEDEC Standard JESD78, which exceeds 100 mA.
  • Bus hold on data inputs eliminates the need for external pullup/pulldown resistors
  • Packaged in thin very small-outline package (TVSOP) — 0.4 mm pitch
  • Optimized for use with PCK953 in SDRAM module applications
  • Balanced ±12 mA output drive
  • Low noise, low skew

DESCRIPTION

The ALVCHS162830 address driver is designed for 2.3 V to 3.6 V VCC operation. Diodes to VCC have been added on the inputs to clamp overshoot. The bus hold feature retains the inputs’ last state whenever the input bus goes to high impedance. This prevents floating inputs and eliminates the need for pull up or pull down resistors. The outputs, which are designed to sink up to 12 mA, include equivalent 26 Ω series resistors to reduce overshoot and undershoot. To ensure the high-impedance state during power up or power down, the output-enable (OE) input should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver. The 74ALVCHS162830 is characterized for operation from –40 to +85 °C. FUNCTION TABLE Inputs Outputs OE1 OE2 A 1Yn 2Yn L H H H Z L H L L Z H L H Z H H L L Z L L L H H H L L L L L H H X Z Z PIN CONFIGURATION 12 69 802Y2 GND 2Y1 1Y1 VCC GND 1Y3 2Y3 GND 1Y4 2Y4 VCC 1Y5 GND 2Y5 1Y6 2Y6 GNDGND 18 63 68A5 VCC 1Y7 VCC 2Y7 1Y8 2Y8 GND 19 62 GND 25 56 61OE1 OE2 A10 GND A11 1Y9 2Y10 2Y9 GND 1Y11 2Y11A12 26 55 VCCVCC 27 54 1Y12A13 32 49 53A14 GND A15 A16 GND 2Y12 1Y13 2Y13 GND 1Y2 GND 1Y10 33 48 1Y14A17 34 47 2Y14A18 35 46 VCCVCC 40 41 452Y18 1Y18 GND 2Y17 1Y17 1Y15 GND 1Y16 2Y16 2Y15 SW00723 TOP VIEW

ORDERING INFORMATION

PACKAGES TEMPERATURE RANGE ORDER CODE DWG NUMBER 80-pin plastic thin very small outline (TVSOP) –40 to +85 °C 74ALVCHS162830DGB SOT647-1

Philips Semiconductors Product data 74ALVCHS16283018-bit to 36-bit address driver with bus hold (3-State)

2001 Sep 07 3

LOGIC DIAGRAM (POSITIVE LOGIC) VCC SW00724 21OE2 20OE1 VCC 7A1 VCC 1Y1 2Y1 to 17 other channels PIN DESCRIPTION PIN(S) SYMBOL FUNCTION 6, 15, 26, 35, 46, 55, 66, 75VCC Supply voltage 22, 24, 25, 27, 28, 30, 31, 33, 34An Inputs 79, 80 1Yn, 2Yn Outputs 20, 21 OE1 , OE2 Output enable 49, 52, 58, 63, 69, 72, 78 GND Ground ABSOLUTE MAXIMUM RATINGS Over recommended operating free-air temperature range (unless otherwise noted).1 SYMBOL PARAMETER CONDITIONS RATING UNIT VCC Supply voltage range –0.5 to +4.6 V VI Input voltage range See Note 2 –0.5 to +4.6 V VO Output voltage range See Notes 2 and 3 –0.5 to VCC +0.5 V IIK Input clamp current VI < 0 –50 mA IOK Output clamp current VO < 0 –50 mA IO Continuous output current /C003450 mA ICC , IGND Continuous current through each VCC or GND /C0034100 mA Θ JA Package thermal impedance See Note 4 106 °C/W Tstg Storage temperature range –65 to +150 °C NOTES: 1. Stresses beyond those listed under ”absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under ”recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 2. The input negative-voltage and output voltage ratings may be exceeded if the input and output current ratings are observed. 3. This value is limited to 4.6 V maximum. 4. The package thermal impedance is calculated in accordance with JESD 51.

Philips Semiconductors Product data 74ALVCHS16283018-bit to 36-bit address driver with bus hold (3-State)

2001 Sep 07 4

RECOMMENDED OPERATING CONDITIONS All unused control inputs of the device must be held at VCC or GND to ensure proper device operation. SYMBOL PARAMETER CONDITIONS LIMITS UNITSYMBOL PARAMETER CONDITIONS MIN MAX UNIT VCC Supply voltage 2.3 3.6 V V High level input voltage VCC = 2.3 V to 2.7 V 1.7 VVIH High-level input voltage VCC = 2.7 V to 3.6 V 2 V V Low level input voltage VCC = 2.3 V to 2.7 V 0.7 VVIL Low-level input voltage VCC = 2.7 V to 3.6 V 0.8 V VI Input voltage 0 VCC V VO Output voltage 0 VCC V VCC = 2.3 V –6 IOH High-level output current VCC = 2.7 V –8 mA VCC = 3 V –12 VCC = 2.3 V 6 IOL Low-level output current VCC = 2.7 V 8 mA VCC = 3 V 12 Δt/Δv Input transition rise or fall rate 10 ns/V Tamb Operating free-air temperature –40 +85 °C

Philips Semiconductors Product data 74ALVCHS16283018-bit to 36-bit address driver with bus hold (3-State)

2001 Sep 07 5

ELECTRICAL CHARACTERISTICS

Over recommended operating free-air temperature range (unless otherwise noted). LIMITS SYMBOL PARAMETER TEST CONDITIONS VCC MIN TYP 1 MAX UNIT V II = –18 mA 2.3 V –1.2 VVIK II = 18 mA 2.3 V VCC +1.2 V IOH = –100 µA 2.3 V to 3.6 V VCC –0.2 IOH = –4 mA, VIH = 1.7 V 2.3 V 1.9 VO H IO =6 m A VIH = 1.7 V 2.3 V 1.7 VOH IOH = –6 mA VIH = 2 V 3 V 2.4 IOH = –8 mA, VIH = 2 V 2.7 V 2 IOH = –12 mA, VIH = 2 V 3 V 2 IOL = 100 µA 2.3 V to 3.6 V 0.2 IOL = 4 mA, VIL = 0.7 V 2.3 V 0.4 VO L IO =6m A VIL = 0.7 V 2.3 V 0.55 VOL IOL = 6 mA VIL = 0.8 V 3 V 0.55 IOL = 8 mA, VIL = 0.8 V 2.7 V 0.6 IOL = 12 mA, VIL = 0.8 V 3 V 0.8 II VI = VCC or GND 3.6 V ±5 µA VI = 0.7 V 2.3 V 45 VI = 1.7 V 2.3 V –45 II(hold) VI = 0.8 V 3 V 75 µA VI = 2 V 3 V –75 VI = 0 to 3.6 V2 3.6 V ±500 IOZ VO = VCC or GND 3.6 V ±10 µA ICC VI = VCC or GND, IO = 0 3.6 V 40 µA ΔICC One input at VCC – 0.6 V, Other inputs at VCC or GND

3 V to

3.6 V 750 µA

C Control inputs V =V CC or GND 33V 3.5 pFC i Data inputs VI = VCC or GND 3.3 V 7.64 pF C o Outputs VO = VCC or GND 3.3 V 3.12 pF NOTES: 1. All typical values are at VCC = 3.3 V, Tamb = 25°C. 2. This is the bus-hold maximum dynamic current. It is the minimum overdrive current required to switch the input from one state to another.

Philips Semiconductors Product data 74ALVCHS16283018-bit to 36-bit address driver with bus hold (3-State)

2001 Sep 07 6

Over recommended operating free-air temperature range (unless otherwise noted) (see Figures 1 and 2). UNIT tpd A Y 1.2 3.8 4 1.7 3.5 ns ten OE Y 1 5.7 5.7 1 4.8 ns tdis OE Y 1 4.9 5.4 1.7 5.2 ns tsk(o)1 Output skew – – – – – – 500 ps NOTE: 1. Output skew between any 2 outputs of same part switching in the same direction. OPERATING CHARACTERISTICS, T amb = 25°C SYMBOL PARAMETER TEST CONDITIONS VCC = 2.5 V ± 0.2 V VCC = 3.3 V ± 0.3 V UNITSYMBOL PARAMETER TEST CONDITIONS TYP TYP UNIT C Power dissipation capacitanceper All outputs enabled C =0 f=1 0M H z 49 53 pFC pd capacitance per driver All outputs disabled C L = 0, f = 10 MH z 6 7.5 pF

2001 Sep 07 7

A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω , tr ≤ 2 ns, tf ≤ 2 ns. D. The outputs are measured one at a time with one transition per measurement. E. tPLZ and tPHZ are the same as tdis. F. tPZL and tPZH are the same as ten. G. tPLH and tPHL are the same as tpd. Figure 1. Load circuit and voltage waveforms

2001 Sep 07 8

A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω , tr ≤ 2.5 ns, tf ≤ 2.5 ns. D. The outputs are measured one at a time with one transition per measurement. E. tPLZ and tPHZ are the same as tdis. F. tPZL and tPZH are the same as ten. G. tPLH and tPHL are the same as tpd. Figure 2. Load circuit and voltage waveforms

Philips Semiconductors Product data 74ALVCHS16283018-bit to 36-bit address driver with bus hold (3-State)

2001 Sep 07 9

TSSOP80: plastic thin shrink small outline package; 80 leads; body width 6.1 mm SOT647-1

Philips Semiconductors Product data 74ALVCHS16283018-bit to 36-bit address driver with bus hold (3-State)

2001 Sep 07 10

Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 60134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Disclaimers Life support — These products are not designed for use in life support appliances, devices or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes — Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Contact information For additional information please visit http://www.semiconductors.philips.com. Fax: +31 40 27 24825 For sales offices addresses send e-mail to:  Koninklijke Philips Electronics N.V. 2001 All rights reserved. Printed in U.S.A. Date of release: 09-01 Document order number: 9397 750 09111 /C0080 /C0115 /C0111/C0110/C0111 /C0115 Data sheet status[1] Objective data Preliminary data Product data Product status[2] Development Qualification Production Definitions This data sheet contains data from the objective specification for product development. Philips Semiconductors reserves the right to change the specification in any manner without notice. This data sheet contains data from the preliminary specification. Supplementary data will be published at a later date. Philips Semiconductors reserves the right to change the specification without notice, in order to improve the design and supply the best possible product. This data sheet contains data from the product specification. Philips Semiconductors reserves the right to make changes at any time in order to improve the design, manufacturing and supply. Changes will be communicated according to the Customer Product/Process Change Notification (CPCN) procedure SNW-SQ-650A. Data sheet status [1] Please consult the most recently issued data sheet before initiating or completing a design. [2] The product status of the device(s) described in this data sheet may have changed since this data sheet was published. The latest information is available on the Internet at URL http://www.semiconductors.philips.com.