74ALVCH16623 PHILIPS

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 16

Technical content

Product specification Supersedes data of 1998 Aug 31 File under Integrated Circuits, IC24

1999 Sep 20

16-bit transceiver with dual enable; 3-state

1999 Sep 20 2

Philips Semiconductors Product specification 16-bit transceiver with dual enable; 3-state 74ALVCH16623

FEATURES

  • Complies with JEDEC standard no. 8-1A
  • CMOS low power consumption
  • Direct interface with TTL levels
  • MULTIBYTE  flow-through standard pin-out architecture
  • All data inputs have bus hold circuitry
  • Output drive capability 50Ω transmission lines at 85°C
  • Current drive±24 mA at 3.0 V.

DESCRIPTION

The 74ALVCH16623 is a high-performance, low-power, low-voltage, Si-gate CMOS device, superior to most advanced CMOS compatible TTL families. The 74ALVCH16623 is a 16-bit transceiver featuring non-inverting 3-state bus compatible outputs in both send and receive directions. This 16-bit bus transceiver is designed for asynchronous two-way communication between data buses. The control function implementation allows maximum flexibility in timing. This device allows data transmission from the A bus to the B bus or from the B bus to the A bus, depending upon the logic levels at the enable inputs (nOE AB ,nOE BA ). The enable inputs can be used to disable the device so that the buses are effectively isolated. The dual enable function configuration gives this transceiver the capability to store data by simultaneous enabling of nOE AB and nOE BA . Each output reinforces its input in this transceiver configuration. Thus, when all control inputs are enabled and all other data sources to the four sets of the bus lines are at high-impedance OFF-state, all sets of bus lines will remain at their last states. The 8-bit codes appearing on the two double sets of buses will be complementary. This device can be used as two 8-bit transceivers or one 16-bit transceiver. To ensure the high-impedance state during power-on or power-down, OE BA should be tied to VCC through a pull-up resistor and OEAB should be tied to GND through a pull-down resistor; the minimum value of the resistor is determined by the current-sinking/current-sourcing capability of the driver. Active bus hold circuitry is provided to hold unused or floating data inputs at a valid logic level. QUICK REFERENCE DATA Ground = 0; T amb =2 5°C; tr =tf= 2.5 ns. Notes 1. C PD is used to determine the dynamic power dissipation (PD inµW). PD =C PD × VCC 2 × fi+ Σ (CL × VCC 2 × fo) where: fi= input frequency in MHz; C L = output load capacitance in pF; fo = output frequency in MHz; VCC = supply voltage in Volts; Σ (CL × VCC 2 × fo) = sum of outputs. 2. The condition is VI= GND to VCC . SYMBOL PARAMETER CONDITIONS TYPICAL UNIT tPHL /tPLH propagation delay nAn,n Bn to nBn,n An C L = 30 pF; VCC = 2.5 V 2.0 ns C L = 50 pF; VCC = 3.3 V 1.9 ns C I/O input/output capacitance 10.0 pF C I input capacitance 3.0 pF C PD power dissipation capacitance per buffer notes 1 and 2 outputs enabled 35 pF outputs disabled 5 pF

1999 Sep 20 3

Philips Semiconductors Product specification 16-bit transceiver with dual enable; 3-state 74ALVCH16623

ORDERING INFORMATION

See note 1. Note 1. H = HIGH voltage level; L = LOW voltage level; Z = high-impedance OFF-state. PINNING TYPE NUMBER PACKAGE TEMPERATURE RANGE PINS PACKAGE MATERIAL CODE 74ALVCH16623DGG −40 to +85°C 48 TSSOP plastic SOT362-1 INPUTS INPUTS/OUTPUTS nOE AB nOE BA nA n nB n L L A = B inputs H H inputs B = A LHZZ H L A=B B=A PIN SYMBOL DESCRIPTION 1, 24 1OE AB , 2OEAB output enable input (active HIGH) 2, 3, 5, 6, 8, 9, 11, 12 1B 0 to 1B7 data inputs/outputs 4, 10, 15, 21, 28, 34, 39, 45 GND ground (0 V) 7, 18, 31, 42 V CC DC supply voltage 13, 14, 16, 17, 19, 20, 22, 23 2B 0 to 2B7 data inputs/outputs 25, 48 2 OE BA , 1OE BA output enable input (active LOW) 26, 27, 29, 30, 32, 33, 35, 36 2A 7 to 2A0 data inputs/outputs 37, 38, 40, 41, 43, 44, 46, 47 1A 7 to 1A0 data inputs/outputs

1999 Sep 20 4

Philips Semiconductors Product specification 16-bit transceiver with dual enable; 3-state 74ALVCH16623 Fig.1 Pin configuration. fpage 16623 MNA307 1OE AB 1B0 1B1 GND 1B2 1B3 VCC 1B4 1B5 GND 1B6 1B7 2B0 2B1 GND 2B2 2B3 VCC 2B4 2B5 GND 2B6 2B7 2OE AB 1OE BA 1A0 1A1 GND 1A2 1A3 VCC 1A4 1A5 GND 1A6 1A7 2A0 2A1 GND 2A2 2A3 VCC 2A4 2A5 GND 2A6 2A7 2OE BA Fig.2 Logic symbol. 1B0 1B1 1B2 1B3 1B4 1B5 1B6 1B7 2B0 2B1 2B2 2B3 2B4 2B5 2B6 2B7 1A0 1A1 1A2 1A3 1A4 1A5 1A6 1A7 2A0 2A1 2A2 2A3 2A4 2A5 2A6 2A7 MNA308 1 24 1OE AB 1OE BA 2OE AB 2OE BA25

1999 Sep 20 5

Philips Semiconductors Product specification 16-bit transceiver with dual enable; 3-state 74ALVCH16623 Fig.3 IEC logic symbol. handbook, halfpage 346 544 643 841 940 1138 1237 1EN1 1EN2 1435 1633 1732 1930 2029 2227 2326 2EN1 2EN2 MNA309 Fig.4 Bus hold circuit. handbook, halfpage to internal circuit MNA310 VCC data input

1999 Sep 20 6

Philips Semiconductors Product specification 16-bit transceiver with dual enable; 3-state 74ALVCH16623 RECOMMENDED OPERATING CONDITIONS LIMITING VALUES In accordance with the Absolute Maximum Rating System (IEC 134); voltages are referenced to GND (ground = 0 V). Notes 1. The input and output voltage ratings may be exceeded if the input and output current ratings are observed. 2. Above 55°C the value of P tot derates linearly with 8 mW/K. SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT VCC DC supply voltage for max. speed performance CL = 30 pF 2.3 2.5 2.7 V for max. speed performance CL = 50 pF 3.0 3.3 3.6 V for low-voltage applications 1.2 2.4 3.6 V VI DC input voltage 0 − VCC V VO DC output voltage 0 − VCC V Tamb operating ambient temperature in free air −40 − +85 °C tr, ft input rise and fall times V CC = 2.3 to 3.0 V 0 − 20 ns/V VCC = 3.0 to 3.6 V 0 − 10 ns/V SYMBOL PARAMETER CONDITIONS MIN. MAX. UNIT VCC DC supply voltage −0.5 +4.6 V IIK DC input diode current V I<0 −− 50 mA VI DC input voltage note 1 −0.5 +4.6 V IOK DC output diode current V O >V CC or VO <0 −± 50 mA VO DC output voltage note 1 −0.5 V CC + 0.5 V IO DC output source or sink current VO =0t oVCC −± 50 mA ICC , IGND DC V CC or GND current −± 100 mA Tstg storage temperature −65 +150 °C Ptot power dissipation for temperature range: −40 to +125°C; note 2 − 600 mW

1999 Sep 20 7

Philips Semiconductors Product specification 16-bit transceiver with dual enable; 3-state 74ALVCH16623 DC CHARACTERISTICS Over recommended operating conditions. Voltage are referenced to GND (ground = 0 V). Notes 1. All typical values are measured at Tamb =2 5°C. 2. Valid for data inputs of bus hold parts. SYMBOL PARAMETER TEST CONDITIONS T amb = −40 TO +85°C UNIT VI(V) OTHER V CC (V) MIN. TYP. (1) MAX. VIH HIGH-level input voltage 2.3 to 2.7 1.7 1.2 − V 2.7 to 3.6 2.0 1.5 − VIL LOW-level input voltage 2.3 to 2.7 − 1.2 0.7 V VOH HIGH-level output voltage VIH or VIL IO = −100 µA 2.3 to 3.6 VCC − 0.2 V CC − V IO = −6 mA 2.3 V CC − 0.3 V CC − 0.08 − IO = −12 mA 2.3 V CC − 0.6 V CC − 0.26 − IO = −12 mA 2.7 V CC − 0.5 V CC − 0.14 − IO = −12 mA 3.0 V CC − 0.6 V CC − 0.09 − IO = −24 mA 3.0 V CC − 1.0 V CC − 0.28 − VOL LOW-level output voltage VIH or VIL IO = 100µA 2.3 to 3.6 − GND 0.20 V IO =6m A 2 . 3 − 0.07 0.40 IO =1 2m A 2 . 3 − 0.15 0.70 IO =1 2m A 2 . 7 − 0.14 0.40 IO =2 4m A 3 . 0 − 0.27 0.55 Il input leakage current V CC or GND 2.3 to 3.6− 0.1 5 µA IOZ 3-state output OFF-state current VIH or VIL VO =V CC or GND 2.3 to 3.6− 0.1 10 µA ICC quiescent supply voltage VCC or GND IO = 0 2.3 to 3.6 − 0.2 40 µA ΔICC additional quiescent supply current given per data I/O pin with bus hold V CC − 0.6 IO = 0 2.3 to 3.6 − 150 750 µA IBHL bus hold LOW sustaining current IBHH bus hold HIGH sustaining current IBHLO bus hold LOW overdrive current 3.6(2) 500 −− µ A IBHHO bus hold LOW overdrive current 3.6(2) −500 −− µ A

1999 Sep 20 8

Philips Semiconductors Product specification 16-bit transceiver with dual enable; 3-state 74ALVCH16623 AC CHARACTERISTICS FOR V CC = 2.3 TO 2.7 V Ground = 0 V; tr =tf≤ 2.0 ns; CL =3 0p F . Note 1. All typical values are measured at Tamb =2 5°C and VCC = 2.5 V. AC CHARACTERISTICS FOR V CC = 2.7 V AND VCC = 3.0 TO 3.6 V Ground = 0 V; tr =tf≤ 2.5 ns; CL =5 0p F . Notes 1. All typical values are measured at Tamb =2 5°C. 2. Typical values at VCC = 3.3 V. SYMBOL PARAMETER TEST CONDITIONS T amb = −40 TO +85°C UNIT WAVEFORMS V CC (V) MIN. TYP. (1) MAX. tPHL /tPLH propagation delay nAn,n Bn to nBn,n An tPZH /tPZL 3-state output enable time nOE AB to nBn tPHZ /tPLZ 3-state output disable time nOE BA to nAn tPZH /tPZL 3-state output enable time nOE AB to nBn tPHZ /tPLZ 3-state output disable time nOE BA to nAn SYMBOL PARAMETER TEST CONDITIONS T amb = −40 TO +85°C UNIT WAVEFORMS V CC (V) MIN. TYP. (1) MAX. tPHL /tPLH propagation delay nAn,n Bn to nBn,n An see Figs 5 and 8 2.7 − 2.5 3.4 ns tPZH /tPZL 3-state output enable time nOE AB to nBn see Figs 7 and 8 2.7 − 2.8 4.5 ns tPHZ /tPLZ 3-state output disable time nOE BA to nAn see Figs 6 and 8 2.7 − 3.3 5.0 ns tPZH /tPZL 3-state output enable time nOE AB to nBn see Figs 7 and 8 2.7 − 3.8 5.4 ns tPHZ /tPLZ 3-state output disable time nOE BA to nAn see Figs 6 and 8 2.7 − 3.2 4.5 ns

1999 Sep 20 9

Philips Semiconductors Product specification 16-bit transceiver with dual enable; 3-state 74ALVCH16623 AC WAVEFORMS Notes: V CC = 2.3 to 2.7 V VM = 0.5VCC ; VX =V OL + 150 mV; VY =V OH − 150 mV; VI=V CC ; VOL and VOH are typical output voltage drop that occur with the output load. Notes: VCC = 3.0 to 3.6 V and VCC = 2.7 V VM = 1.5 V; VX =V OL + 300 mV; VY =V OH − 300 mV; VI= 2.7 V; VOL and VOH are typical output voltage drop that occur with the output load. Fig.5 The input nAn, nBn to output nBn, nAn propagation delay times. handbook, halfpage MNA311 nAn, nBn input nBn, nAn output tPHL tPLH GND VI VM VM VOH VOL Fig.6 3-state enable and disable times for nOE BA input. handbook, full pagewidth MNA312 tPLZ tPHZ outputs disabled outputs enabled VY VX outputs enabled output LOW-to-OFF OFF-to-LOW output HIGH-to-OFF OFF-to-HIGH nOE BA input VI VOL VOH VCC VM GND GND tPZL tPZH VM VM

1999 Sep 20 10

Philips Semiconductors Product specification 16-bit transceiver with dual enable; 3-state 74ALVCH16623 Fig.7 3-state enable and disable times for nOEAB times. handbook, full pagewidth MNA313 tPLZ tPHZ outputs disabled outputs enabled VY VX outputs enabled output LOW-to-OFF OFF-to-LOW output HIGH-to-OFF OFF-to-HIGH nOE AB input VI VOL VOH VCC VM GND GND tPZL tPZH VM VM Fig.8 Load circuitry for switching times. handbook, full pagewidth open GND 50 pF 2 × VCC VCC VI VO MNA296 D.U.T. C LR T R L 500 Ω R L 500 Ω PULSE GENERATOR VCC VI <2.7 V V CC 2.7 to 3.6 V 2.7 V TEST S1 tPLH /tPHL open tPLZ /tPZL 2 × VCC tPHZ /tPZH GND Definitions for test circuit. C L = load capacitance including jig and probe capacitance (See Chapter “AC characteristics”). R L = load resistance. R T = termination resistance should be equal to the output impedance Zo of the pulse generator.

1999 Sep 20 11

Philips Semiconductors Product specification 16-bit transceiver with dual enable; 3-state 74ALVCH16623 PACKAGE OUTLINE UNIT A 1 A 2 A 3 bp cD (1) E (2) eH E LL p QZ ywv θ REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC EIAJ mm 0.15 0.05 0.2 0.1 o o0.1 DIMENSIONS (mm are the original dimensions). Notes 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. Plastic interlead protrusions of 0.25 mm maximum per side are not included. SOT362-1 93-02-03 95-02-10 w M θ AA 1 A 2 D Lp Q detail X E Z e c L X (A )3 0.25 12 4 48 25 y pin 1 index b H 1.05 0.85 0.28 0.17 0.2 0.1 12.6 12.4 6.2 6.0 0.5 1 0.258.3 7.9 0.50 0.35 0.8 0.40.080.8 0.4 p E v M A A TSSOP48: plastic thin shrink small outline package; 48 leads; body width 6.1 mm SOT362-1 A max. 1.2 0 2.5 5 mm scale MO-153ED

1999 Sep 20 12

Philips Semiconductors Product specification 16-bit transceiver with dual enable; 3-state 74ALVCH16623 SOLDERING Introduction to soldering surface mount packages This text gives a very brief insight to a complex technology. A more in-depth account of soldering ICs can be found in our “Data Handbook IC26; Integrated Circuit Packages” (document order number 9398 652 90011). There is no soldering method that is ideal for all surface mount IC packages. Wave soldering is not always suitable for surface mount ICs, or for printed-circuit boards with high population densities. In these situations reflow soldering is often used. Reflow soldering Reflow soldering requires solder paste (a suspension of fine solder particles, flux and binding agent) to be applied to the printed-circuit board by screen printing, stencilling or pressure-syringe dispensing before package placement. Several methods exist for reflowing; for example, infrared/convection heating in a conveyor type oven. Throughput times (preheating, soldering and cooling) vary between 100 and 200 seconds depending on heating method. Typical reflow peak temperatures range from 215 to 250°C. The top-surface temperature of the packages should preferable be kept below 230°C. Wave soldering Conventional single wave soldering is not recommended for surface mount devices (SMDs) or printed-circuit boards with a high component density, as solder bridging and non-wetting can present major problems. To overcome these problems the double-wave soldering method was specifically developed. If wave soldering is used the following conditions must be observed for optimal results:

  • Use a double-wave soldering method comprising a turbulent wave with high upward pressure followed by a smooth laminar wave.
  • For packages with leads on two sides and a pitch (e): – larger than or equal to 1.27 mm, the footprint longitudinal axis ispreferred to be parallel to the transport direction of the printed-circuit board; – smaller than 1.27 mm, the footprint longitudinal axis must be parallel to the transport direction of the printed-circuit board. The footprint must incorporate solder thieves at the downstream end.
  • For packages with leads on four sides, the footprint must be placed at a 45° angle to the transport direction of the printed-circuit board. The footprint must incorporate solder thieves downstream and at the side corners. During placement and before soldering, the package must be fixed with a droplet of adhesive. The adhesive can be applied by screen printing, pin transfer or syringe dispensing. The package can be soldered after the adhesive is cured. Typical dwell time is 4 seconds at 250°C. A mildly-activated flux will eliminate the need for removal of corrosive residues in most applications. Manual soldering Fix the component by first soldering two diagonally-opposite end leads. Use a low voltage (24 V or less) soldering iron applied to the flat part of the lead. Contact time must be limited to 10 seconds at up to 300 °C. When using a dedicated tool, all other leads can be soldered in one operation within 2 to 5 seconds between 270 and 320°C.

1999 Sep 20 13

Philips Semiconductors Product specification 16-bit transceiver with dual enable; 3-state 74ALVCH16623 Suitability of surface mount IC packages for wave and reflow soldering methods Notes 1. All surface mount (SMD) packages are moisture sensitive. Depending upon the moisture content, the maximum temperature (with respect to time) and body size of the package, there is a risk that internal or external package cracks may occur due to vaporization of the moisture in them (the so called popcorn effect). For details, refer to the Drypack information in the “Data Handbook IC26; Integrated Circuit Packages; Section: Packing Methods”. 2. These packages are not suitable for wave soldering as a solder joint between the printed-circuit board and heatsink (at bottom version) can not be achieved, and as solder may stick to the heatsink (on top version). 3. If wave soldering is considered, then the package must be placed at a 45° angle to the solder wave direction. The package footprint must incorporate solder thieves downstream and at the side corners. 4. Wave soldering is only suitable for LQFP, TQFP and QFP packages with a pitch (e) equal to or larger than 0.8 mm; it is definitely not suitable for packages with a pitch (e) equal to or smaller than 0.65 mm. 5. Wave soldering is only suitable for SSOP and TSSOP packages with a pitch (e) equal to or larger than 0.65 mm; it is definitely not suitable for packages with a pitch (e) equal to or smaller than 0.5 mm. DEFINITIONS LIFE SUPPORT APPLICATIONS These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale. PACKAGE SOLDERING METHOD WAVE REFLOW (1) BGA, SQFP not suitable suitable HLQFP , HSQFP , HSOP , HTSSOP , SMS not suitable(2) suitable PLCC (3), SO, SOJ suitable suitable LQFP , QFP , TQFP not recommended (3)(4) suitable SSOP , TSSOP , VSO not recommended (5) suitable Data sheet status Objective specification This data sheet contains target or goal specifications for product development. Preliminary specification This data sheet contains preliminary data; supplementary data may be published later. Product specification This data sheet contains final product specifications. Limiting values Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability.

Application information

Where application information is given, it is advisory and does not form part of the specification.

1999 Sep 20 14

Philips Semiconductors Product specification 16-bit transceiver with dual enable; 3-state 74ALVCH16623 NOTES

1999 Sep 20 15

Philips Semiconductors Product specification 16-bit transceiver with dual enable; 3-state 74ALVCH16623 NOTES

© Philips Electronics N.V. SCA All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights. Internet: http://www.semiconductors.philips.com 1999 68 Philips Semiconductors – a worldwide company For all other countries apply to: Philips Semiconductors, International Marketing & Sales Communications, Building BE-p, P.O. Box 218, 5600 MD EINDHOVEN, The Netherlands, Fax. +31 40 27 24825 Argentina: see South America Australia: 3 Figtree Drive, HOMEBUSH, NSW 2140, Tel. +61 2 9704 8141, Fax. +61 2 9704 8139 Austria:Computerstr. 6, A-1101 WIEN, P.O. Box 213, Tel. +43 1 60 101 1248, Fax. +43 1 60 101 1210 Belarus: Hotel Minsk Business Center, Bld. 3, r. 1211, Volodarski Str. 6, 220050 MINSK, Tel. +375 172 20 0733, Fax. +375 172 20 0773 Belgium: see The Netherlands Brazil:see South America Bulgaria:Philips Bulgaria Ltd., Energoproject, 15th floor, 51 James Bourchier Blvd., 1407 SOFIA, Tel. +359 2 68 9211, Fax. +359 2 68 9102 Canada: PHILIPS SEMICONDUCTORS/COMPONENTS, Tel. +1 800 234 7381, Fax. +1 800 943 0087 China/Hong Kong: 501 Hong Kong Industrial Technology Centre,

72 Tat Chee Avenue, Kowloon Tong, HONG KONG,

Tel. +852 2319 7888, Fax. +852 2319 7700 Colombia: see South America Czech Republic: see Austria Denmark: Sydhavnsgade 23, 1780 COPENHAGEN V, Tel. +45 33 29 3333, Fax. +45 33 29 3905 Finland: Sinikalliontie 3, FIN-02630 ESPOO, Tel. +358 9 615 800, Fax. +358 9 6158 0920 France: 51 Rue Carnot, BP317, 92156 SURESNES Cedex, Tel. +33 1 4099 6161, Fax. +33 1 4099 6427 Germany: Hammerbrookstraße 69, D-20097 HAMBURG, Tel. +49 40 2353 60, Fax. +49 40 2353 6300 Hungary: see Austria India: Philips INDIA Ltd, Band Box Building, 2nd floor, 254-D, Dr. Annie Besant Road, Worli, MUMBAI 400 025, Tel. +91 22 493 8541, Fax. +91 22 493 0966 Indonesia:PT Philips Development Corporation, Semiconductors Division, Gedung Philips, Jl. Buncit Raya Kav.99-100, JAKARTA 12510, Tel. +62 21 794 0040 ext. 2501, Fax. +62 21 794 0080 Ireland: Newstead, Clonskeagh, DUBLIN 14, Tel. +353 1 7640 000, Fax. +353 1 7640 200 Israel: RAPAC Electronics, 7 Kehilat Saloniki St, PO Box 18053, TEL AVIV 61180, Tel. +972 3 645 0444, Fax. +972 3 649 1007 Italy:PHILIPS SEMICONDUCTORS, Via Casati, 23 - 20052 MONZA (MI), Tel. +39 039 203 6838, Fax +39 039 203 6800 Japan: Philips Bldg 13-37, Kohnan 2-chome, Minato-ku, TOKYO 108-8507, Tel. +81 3 3740 5130, Fax. +81 3 3740 5057 Korea: Philips House, 260-199 Itaewon-dong, Yongsan-ku, SEOUL, Tel. +82 2 709 1412, Fax. +82 2 709 1415 Malaysia: No. 76 Jalan Universiti, 46200 PETALING JAYA, SELANGOR, Tel. +60 3 750 5214, Fax. +60 3 757 4880 Mexico: 5900 Gateway East, Suite 200, EL PASO, TEXAS 79905, Tel. +9-5 800 234 7381, Fax +9-5 800 943 0087 Middle East: see Italy Netherlands: Postbus 90050, 5600 PB EINDHOVEN, Bldg. VB, Tel. +31 40 27 82785, Fax. +31 40 27 88399 New Zealand: 2 Wagener Place, C.P.O. Box 1041, AUCKLAND, Tel. +64 9 849 4160, Fax. +64 9 849 7811 Norway: Box 1, Manglerud 0612, OSLO, Tel. +47 22 74 8000, Fax. +47 22 74 8341 Pakistan: see Singapore Philippines: Philips Semiconductors Philippines Inc., 106 Valero St. Salcedo Village, P.O. Box 2108 MCC, MAKATI, Metro MANILA, Tel. +63 2 816 6380, Fax. +63 2 817 3474 Poland: Al.Jerozolimskie 195 B, 02-222 WARSAW, Tel. +48 22 5710 000, Fax. +48 22 5710 001 Portugal: see Spain Romania: see Italy Russia: Philips Russia, Ul. Usatcheva 35A, 119048 MOSCOW, Tel. +7 095 755 6918, Fax. +7 095 755 6919 Singapore: Lorong 1, Toa Payoh, SINGAPORE 319762, Tel. +65 350 2538, Fax. +65 251 6500 Slovakia: see Austria Slovenia: see Italy South Africa: S.A. PHILIPS Pty Ltd., 195-215 Main Road Martindale, 2092 JOHANNESBURG, P.O. Box 58088 Newville 2114, Tel. +27 11 471 5401, Fax. +27 11 471 5398 South America: Al. Vicente Pinzon, 173, 6th floor, 04547-130 SÃO PAULO, SP, Brazil, Tel. +55 11 821 2333, Fax. +55 11 821 2382 Spain: Balmes 22, 08007 BARCELONA, Tel. +34 93 301 6312, Fax. +34 93 301 4107 Sweden: Kottbygatan 7, Akalla, S-16485 STOCKHOLM, Tel. +46 8 5985 2000, Fax. +46 8 5985 2745 Switzerland: Allmendstrasse 140, CH-8027 ZÜRICH, Tel. +41 1 488 2741 Fax. +41 1 488 3263 Taiwan: Philips Semiconductors, 6F, No. 96, Chien Kuo N. Rd., Sec. 1, TAIPEI, Taiwan Tel. +886 2 2134 2886, Fax. +886 2 2134 2874 Thailand: PHILIPS ELECTRONICS (THAILAND) Ltd., 209/2 Sanpavuth-Bangna Road Prakanong, BANGKOK 10260, Tel. +66 2 745 4090, Fax. +66 2 398 0793 ISTANBUL, Tel. +90 216 522 1500, Fax. +90 216 522 1813 Ukraine: PHILIPS UKRAINE, 4 Patrice Lumumba str., Building B, Floor 7, 252042 KIEV, Tel. +380 44 264 2776, Fax. +380 44 268 0461 United Kingdom: Philips Semiconductors Ltd., 276 Bath Road, Hayes, MIDDLESEX UB3 5BX, Tel. +44 208 730 5000, Fax. +44 208 754 8421 United States: 811 East Arques Avenue, SUNNYVALE, CA 94088-3409, Tel. +1 800 234 7381, Fax. +1 800 943 0087 Uruguay: see South America Vietnam: see Singapore Yugoslavia: PHILIPS, Trg N. Pasica 5/v, 11000 BEOGRAD, Tel. +381 11 62 5344, Fax.+381 11 63 5777 Printed in The Netherlands 245004/02/pp16 Date of release:1999 Sep 20 Document order number: 9397 750 05254