74ALVCH16540 PHILIPS

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 12

Technical content

/C0109 /C0110 /C0114 74ALVCH16540 2.5V/3.3V 16-bit buffer/line driver, inverting, 5V input tolerant (3-State) Product specification Supersedes data of 1996 Feb 07 IC24 Data Handbook

1997 Aug 11

Philips Semiconductors Product specification 74ALVCH1654016-bit buffer/line driver, inverting, 5V input tolerant (3-State)

21997 Aug 11 853-2020 18266

FEATURES

  • Wide supply voltage range of 1.2 V to 3.6 V
  • Complies with JEDEC standard no. 8-1A
  • CMOS low power consumption
  • MULTIBYTE TM flow-through standard pin-out architecture
  • Low inductance multiple VCC and ground pins for minimum noise and ground bounce
  • Direct interface with TTL levels
  • Bus hold on all data inputs eliminates the need for external pull-up resistors to hold unused inputs
  • Output drive capability 50Ω transmission lines @ 85°C

DESCRIPTION

The 74ALVCH16540 is a high-performance, low-power, low-voltage, Si-gate CMOS device, superior to most advanced CMOS compatible TTL families. The 74ALVCH16540 is a 16-bit inverting buffer/line driver with 3-State outputs. The 3-State outputs are controlled by the output enable inputs 1OEn and 2OEn. A HIGH on nOEn causes the outputs to assume a high impedance OFF-state. Active bus hold circuitry is provided to hold unused or floating data inputs at a valid logic level. This feature eliminates the need for external pull-up or pull-down resistors. The device can be used as four 4-bit buffers, two 8-bit buffers or one 16-bit buffer. PIN CONFIGURATION 20 29 481OE 1Y0 1Y1 GND 1Y2 1Y3 VCC 1Y5 GND 1Y6 1Y7 2Y0 2Y1 GND 1Y4 2Y2 2Y3 VCC 2Y4 2Y5 2A5 2A4 VCC 2A3 2A2 GND 2A1 2A0 1A7 1A6 GND 1A5 1A4 V CC 1A3 1A2 GND 1A1 1A0 1OE 24 25 28GND 2Y6 2Y7 2OE 1 2OE 2 2A7 2A6 GND SW00108 QUICK REFERENCE DATA GND = 0V; Tamb = 25°C; tr = tf ≤ 2.5ns SYMBOL PARAMETER CONDITIONS TYPICAL UNIT t /t Propagation delay 1An to 1Yn; C L = 50pF VCC = 3.3V 1.8 ns tPHL /tPLH 1An to 1Yn; 2An to 2Yn C L = 30pF VCC = 2.5V 1.8 ns C I Input capacitance 5.0 pF C Power dissipation capacitanceper buffer V = GND to VCC 1 Outputs enabled 26 pF C PD Pow er dissipation capacitance per buffer VI = GND to VCC 1 Outputs disabled 5 pF NOTES: 1. CPD is used to determine the dynamic power dissipation (PD in W): PD = CPD × VCC 2 × fi + (CL × VCC 2 × fo) where: fi = input frequency in MHz; CL = output load capacitance in pF; fo = output frequency in MHz; VCC = supply voltage in V; (CL × VCC 2 × fo) = sum of outputs.

ORDERING INFORMATION

PACKAGES TEMPERATURE RANGE OUTSIDE NORTH AMERICA NORTH AMERICA DWG NUMBER 48-Pin Plastic SSOP Type III –40°C to +85°C 74ALVCH16540 DL ACH16540 DL SOT370-1 48-Pin Plastic TSSOP Type II –40°C to +85°C 74ALVCH16540 DGG ACH16540 DGG SOT362-1

Philips Semiconductors Product specification 74ALVCH1654016-bit buffer/line driver, inverting, 5V input tolerant (3-State)

1997 Aug 11 3

PIN NUMBER SYMBOL NAME AND FUNCTION 1, 24 nOE 1 Output enable input (active LOW) 2, 3, 5, 6, 8, 9, 11, 12 1Y0 to 1Y7 Data outputs 13, 14, 16, 17, 19, 20, 22, 23 2Y0 to 2Y7 Data outputs 4, 10, 15, 21, 28, 34, 39, 45 GND Ground (0V) 7, 18, 31, 42 VCC Positive supply voltage 25, 48 nOE 2 Output enable input (active LOW) 36, 35, 33, 32, 30, 29, 27, 26 2A0 to 2A7 Data inputs 47, 46, 44, 43, 41, 40, 38, 37 1A0 to 1A7 Data inputs LOGIC SYMBOL 1A0 47 2 1Y0 1A1 46 3 1Y1 1A2 44 5 1Y2 1A3 43 6 1Y3 1A4 41 8 1Y4 1A5 40 9 1Y5 1A6 38 11 1Y6 1A7 37 12 1Y7 1OE 1 1OE 2 2A0 36 13 2Y0 2A1 35 14 2Y1 2A2 33 16 2Y2 2A3 32 17 2Y3 2A4 30 19 2Y4 2A5 29 20 2Y5 2A6 27 22 2Y6 2A7 26 23 2Y7 2OE 1 2OE 2 SW00109 FUNCTION TABLE INPUTS OUTPUT nOE 1 nOE 2 nAn nYn L L L H L L H L X H X Z H X X Z H = HIGH voltage level L = LOW voltage level X = don’t care Z = high impedance OFF-state LOGIC SYMBOL (IEEE/IEC) 1 ∇ EN2 2 ∇1 SW00110 1OE 1 1OE 2 2OE 1 2OE 2 1A0 1A1 1A2 1A3 1A4 1A5 1A6 2A0 2A1 2A2 2A3 2A4 2A5 2A6 2A7 1Y0 1Y1 1Y2 1Y3 1Y4 1Y5 1Y6 1Y7 2Y0 2Y1 2Y2 2Y3 2Y4 2Y7 1A7 2Y5 2Y6 EN1 BUS HOLD CIRCUIT To internal circuit VCC Data Input SW00044

Philips Semiconductors Product specification 74ALVCH1654016-bit buffer/line driver, inverting, 5V input tolerant (3-State)

1997 Aug 11 4

RECOMMENDED OPERATING CONDITIONS SYMBOL PARAMETER CONDITIONS LIMITS UNITSYMBOL PARAMETER CONDITIONS MIN MAX UNIT DC supply voltage 2.5V range (for max. speed performance) 2.3 2.7 VCC DC supply voltage 3.3V range (for max. speed performance) 3.0 3.6 V DC supply voltage (for low-voltage applications) 1.2 3.6 V DC Input voltage range For data input pins 0 VCC VVI DC Input voltage range For control pins 0 5.5 V VO DC output voltage range 0 VCC V Tamb Operating free-air temperature range –40 +85 °C tr, tf Input rise and fall times VCC = 2.3 to 3.0V VCC = 3.0 to 3.6V ns/V ABSOLUTE MAXIMUM RATINGS 1, 2 In accordance with the Absolute Maximum Rating System (IEC 134) Voltages are referenced to GND (ground = 0V) SYMBOL PARAMETER CONDITIONS RATING UNIT VCC DC supply voltage –0.5 to +4.6 V IIK DC input diode current VI 0 –50 mA VI DC input voltage For control pins and data inputs of ALVC parts2 –0.5 to +5.5 VI g For data inputs of ALVCH parts2 –0.5 to VCC +0.5 IOK DC output diode current VO VCC or VO 0 50 mA VO DC output voltage Note 2 –0.5 to VCC +0.5 V IO DC output source or sink currentVO = 0 to VCC 50 mA IGND , ICC DC V CC or GND current 100 mA Tstg Storage temperature range –65 to +150 °C PTOT Power dissipation per package –plastic medium-shrink SO (SSOP) –plastic mini-pack (TSSOP) For temperature range: –40 to +125 °C above +55°C derate linearly with 11.3 mW/K above +55°C derate linearly with 8 mW/K 850 600 mW NOTES: 1. Stresses beyond those listed may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 2. The input and output voltage ratings may be exceeded if the input and output current ratings are observed.

Philips Semiconductors Product specification 74ALVCH1654016-bit buffer/line driver, inverting, 5V input tolerant (3-State)

1997 Aug 11 5

DC ELECTRICAL CHARACTERISTICS LIMITS SYMBOL PARAMETER TEST CONDITIONS Temp = -40°C to +85°C UNIT MIN TYP 1 MAX VCC = 1.2V VCC VIH HIGH level Input voltage VCC = 2.3 to 2.7V 1.7 V VCC = 2.7 to 3.6V 2.0 VCC = 1.2V GND VIL LOW level Input voltage VCC = 2.3 to 2.7V 0.7 V VCC = 2.7 to 3.6V 0.8 VCC = 2.3V; VI = VIH or VIL; IO = –1mA VCC /C00420.3 VCC = 2.3V; VI = VIH or VIL; IO = –8mA VCC /C00420.5 VOH HIGH level output voltage VCC = 2.7V; VI = VIH or VIL; IO = –12mA VCC /C00420.5 V VCC = 2.3/3.0V; VI = VIH or VIL; IO = –100µA VCC /C00420.2 VCC VCC = 3.0V; VI = VIH or VIL; IO = –24mA VCC /C00421.0 VCC = 2.3V; VI = VIH or VIL; IO = 1mA 0.40 VCC = 2.3V; VI = VIH or VIL; IO = 8mA 0.60 VOL LOW level output voltage VCC = 2.7V; VI = VIH or VIL; IO = 12mA 0.40 V VCC = 2.3/3.0V; VI = VIH or VIL; IO = 100µA 0.20 VCC = 3.0V; VI = VIH or VIL; IO = 24mA 0.55 VCC =36 V;V = 5 5V or GND Controlpins 01 5 I Input leakage current VCC = 3.6V; VI = 5.5V or GND Control pins 0.1 5 µAII Input leakage current VCC = 3.6V; VI = VCC or GND Data input pins 0.1 5 µA IIHZ/IILZ Input current for common I/O pinsVCC = 3.6V; VI = VCC or GND 0.1 15 µA IO 3-State output OFF-state current VCC = 3.6V; VI = VIH or VIL; VO = VCC or GND 0.1 10 µAIOZ 3-State output OFF-state current VCC = 2.7V; VI = VIH or VIL; VO = VCC or GND 0.1 5 µA ICC Quiescent supply current VCC = 3.6V; VI = VCC or GND; IO = 0 0.2 40 µAICC Quiescent supply current VCC = 2.7V; VI = VCC or GND; IO = 0 0.2 20 µA ΔICC Additional quiescent supply current per control pin VCC = 2.7V to 3.6V; VI = VCC –0.6V; IO = 0 5 500 µAΔICC Additional quiescent supply current per data I/O pin VCC = 2.7V to 3.6V; VI = VCC –0.6V; IO = 0 150 750 µA IBHL Bus hold LOW sustaining current VCC = 2.3V; VI = 0.7V 45 µAIBHL Bus hold LOW sustaining current VCC = 3.0V; VI = 0.8V 75 µA IBHH Bus hold HIGH sustaining current VCC = 2.3V; VI = 1.7V –45 µAIBHH Bus hold HIGH sustaining current VCC = 3.0V; VI = 2.0V –75 µA IBHLO Bus hold LOW overdrive current VCC = 2.7V 300 µAIBHLO Bus hold LOW overdrive current VCC = 3.6V 450 µA IBHHO Bus hold HIGH overdrive current VCC = 2.7V –300 µAIBHHO Bus hold HIGH overdrive current VCC = 3.6V –450 µA NOTES: 1. All typical values are at VCC = 3.3V and Tamb = 25°C.

Philips Semiconductors Product specification 74ALVCH1654016-bit buffer/line driver, inverting, 5V input tolerant (3-State)

1997 Aug 11 6

AC CHARACTERISTICS FOR V CC = 3.0V TO 3.6V RANGE AND VCC = 2.7V GND = 0V; tr = tf ≤ 2.5ns; CL = 50pF LIMITS SYMBOL PARAMETER WAVEFORM VCC = 3.0 ± 0.3V VCC = 2.7V UNIT MIN TYP 1 MAX TYP MAX tPHL /tPLH Propagation delay 1An to 1Yn; 2An to 2Yn 4 1.8 3.0 2.1 3.6 ns tPZH /tPZL 3-State output enable time 1OE n to 1Yn; 2OE n to 2Yn 5, 6 2.1 3.8 2.9 4.7 ns tPHZ /tPLZ 3-State output disable time 1OE n to 1Yn; 2OE n to 2Yn 5, 6 2.7 4.1 3.2 4.5 ns NOTE: 1. All typical values are at VCC = 3.3V and Tamb = 25°C. AC CHARACTERISTICS FOR V CC = 2.3V TO 2.7V RANGE AND VCC < 2.3V GND = 0V; tr = tf ≤ 2.0ns; CL = 30pF LIMITS SYMBOL PARAMETER WAVEFORM VCC = 2.3 to 2.7V VCC = 1.8V VCC = 1.2V UNIT MIN TYP 1 MAX TYP MAX tPHL /tPLH Propagation delay 1An to 1Yn; 2An to 2Yn 4 1.8 3.2 3.1 6.0 ns tPZH /tPZL 3-State output enable time 1OE n to 1Yn; 2OE n to 2Yn 5, 6 2.5 4.4 4.3 8.9 ns tPHZ /tPLZ 3-State output disable time 1OE n to 1Yn; 2OE n to 2Yn 5, 6 2.2 3.8 3.6 6.4 ns NOTE: 1. All typical values are at VCC = 2.5V and Tamb = 25°C. AC WAVEFORMS FOR V CC = 3.0V TO 3.6V AND VCC = 2.7V RANGE VM = 1.5 V VX = VOL + 0.3V VY = VOH –0.3V VOL and VOH are the typical output voltage drop that occur with the output load. VI = 2.7V SW00111 nAn INPUT VM tPHL tPLH VOL VI VM GND VOH nYn OUTPUT Waveform 1. Input (An) to output (Yn) propagation delay times tPLZ tPZL VI OE INPUT GND VCC Y OUTPUT LOW-to-OFF OFF-to-LOW VOL VOH Y OUTPUT HIGH-to-OFF OFF-to-HIGH GND outputs enabled outputs enabled outputs disabled tPHZ VM VM VM tPZH VX VY SW00112 Waveform 2. 3-State enable and disable times

Philips Semiconductors Product specification 74ALVCH1654016-bit buffer/line driver, inverting, 5V input tolerant (3-State)

1997 Aug 11 7

D.U.T. VOUT C L VCC R L=500 Ω SWITCH POSITION TEST SWITCH tPLH /tPHL Open tPLZ /tPZL 2/C0060VCC tPHZ /tPZH GND Test Circuit for 3-State Outputs Open GND 2/C0060VCC DEFINITIONS VCC 2.7V 2.7 – 3.6V VIN VCC 2.7V R L = Load resistor C L = Load capacitance includes jig and probe capacitance R T = Termination resistance should be equal to ZOUT of pulse generators. SW00047 R L=500 Ω Waveform 3. Load circuitry for switching times AC WAVEFORMS FOR V CC = 2.3V TO 2.7V AND VCC < 2.3V RANGE VM = 0.5 * VCC VX = VOL + 0.15V VY = VOH –0.15V VOL and VOH are the typical output voltage drop that occur with the output load. VI = VCC SW00111 nAn INPUT VM tPHL tPLH VOL VI VM GND VOH nYn OUTPUT Waveform 4. Input (An) to output (Yn) propagation delay times tPLZ tPZL VI OE INPUT GND VCC Y OUTPUT LOW-to-OFF OFF-to-LOW VOL VOH Y OUTPUT HIGH-to-OFF OFF-to-HIGH GND outputs enabled outputs enabled outputs disabled tPHZ VM VM VM tPZH VX VY SW00112 Waveform 5. 3-State enable and disable times

Philips Semiconductors Product specification 74ALVCH1654016-bit buffer/line driver, inverting, 5V input tolerant (3-State)

1997 Aug 11 8

D.U.T. VOUT C L VCC R L=500 Ω SWITCH POSITION TEST SWITCH tPLH /tPHL Open tPLZ /tPZL 2/C0060VCC tPHZ /tPZH GND Test Circuit for 3-State Outputs Open GND 2/C0060VCC DEFINITIONS VCC 2.7V 2.7 – 3.6V VIN VCC 2.7V R L = Load resistor C L = Load capacitance includes jig and probe capacitance R T = Termination resistance should be equal to ZOUT of pulse generators. SW00047 R L=500 Ω Waveform 6. Load circuitry for switching times

Philips Semiconductors Product specification 74ALVCH165402.5V/3.3V 16-bit buffer/line driver, inverting, 5V input tolerant (3-State)

1997 Aug 11 9

SSOP48: plastic shrink small outline package; 48 leads; body width 7.5 mm SOT370-1

Philips Semiconductors Product specification 74ALVCH165402.5V/3.3V 16-bit buffer/line driver, inverting, 5V input tolerant (3-State)

1997 Aug 11 10

TSSOP48: plastic thin shrink small outline package; 48 leads; body width 6.1mm SOT362-1

Philips Semiconductors Product specification 74ALVCH165402.5V/3.3V 16-bit buffer/line driver, inverting, 5V input tolerant (3-State)

1997 Aug 11 11

Philips Semiconductors Product specification 74ALVCH165402.5V/3.3V 16-bit buffer/line driver, inverting, 5V input tolerant (3-State)

1997 Aug 11 12

Philips Semiconductors and Philips Electronics North America Corporation reserve the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. LIFE SUPPORT APPLICATIONS Philips Semiconductors and Philips Electronics North America Corporation Products are not designed for use in life support appliances, devices, or systems where malfunction of a Philips Semiconductors and Philips Electronics North America Corporation Product can reasonably be expected to result in a personal injury. Philips Semiconductors and Philips Electronics North America Corporation customers using or selling Philips Semiconductors and Philips Electronics North America Corporation Products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors and Philips Electronics North America Corporation for any damages resulting from such improper use or sale. This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips Semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. Philips Semiconductors

811 East Arques Avenue

P.O. Box 3409 Sunnyvale, California 94088–3409 Telephone 800-234-7381 DEFINITIONS Data Sheet Identification Product Status Definition Objective Specification Preliminary Specification Product Specification Formative or in Design Preproduction Product Full Production This data sheet contains the design target or goal specifications for product development. Specifications may change in any manner without notice. This data sheet contains Final Specifications. Philips Semiconductors reserves the right to make changes at any time without notice, in order to improve design and supply the best possible product.  Copyright Philips Electronics North America Corporation 1998 All rights reserved. Printed in U.S.A. Date of release: 08–97 Document order number: 9397-750-04545 /C0109 /C0110 /C0114