74ALVCH16374 PHILIPS

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 12

Technical content

/C0109 /C0110 /C0114 74ALVCH16374 2.5V/3.3V 16-bit edge-triggered D-type flip-flop (3-State) Product specification Supersedes data of 1997 Mar 21 IC24 Data Handbook

1998 Jun 18

Philips Semiconductors Product specification 74ALVCH1637416-bit edge-triggered D-type flip-flop (3-State)

21998 Jun 18 853-2073 19604

FEATURES

  • Wide supply voltage range of 1.2 V to 3.6 V
  • Complies with JEDEC standard no. 8-1A
  • CMOS low power consumption
  • MULTIBYTE TM flow-through standard pin-out architecture
  • Low inductance multiple VCC and ground pins for minimum noise and ground bounce
  • Direct interface with TTL levels
  • All data inputs have bushold
  • Output drive capability 50Ω transmission lines @ 85°C
  • Current drive ±24 mA at 3.0 V

DESCRIPTION

The 74ALVCH16374 is a 16-bit edge-triggered flip-flop featuring separate D-type inputs for each flip-flop and 3-State outputs for bus oriented applications. Incorporates bus hold data inputs which eliminate the need for external pull-up or pull-down resistors to hold unused inputs. The 74ALVCH16374 consists of 2 sections of eight edge-triggered flip-flops. A clock (CP) input and an output enable (OE ) are provided per 8-bit section. The flip-flops will store the state of their individual D-inputs that meet the set-up and hold time requirements on the LOW-to-HIGH CP transition. When OE is LOW, the contents of the flip-flops are available at the outputs. When OE is HIGH, the outputs go to the high impedance OFF-state. Operation of the OE input does not affect the state of the flip-flops. PIN CONFIGURATION 20 29 481OE 1Q0 1Q1 GND 1Q2 1Q3 VCC 1Q5 GND 1Q6 1Q7 2Q0 2Q1 GND 1Q4 2Q2 2Q3 V CC 2Q4 2Q5 2D5 2D4 VCC 2D3 2D2 GND 2D1 2D0 1D7 1D6 GND 1D5 1D4 V CC 1D3 1D2 GND 1D1 1D0 1CP 24 25 28GND 2Q6 2Q7 2OE 2CP 2D7 2D6 GND SW00074 QUICK REFERENCE DATA GND = 0V; Tamb = 25°C; tr = tf ≤ 2.5 ns SYMBOL PARAMETER CONDITIONS TYPICAL UNIT t /t Propagation delay VCC = 2.5V, CL = 30pF 2.3 nstPHL /tPLH gy CP to Qn VCC = 3.3V, CL = 50pF 2.4 ns f Maximum clock frequency VCC = 2.5V 300 MHz fMAX Ma ximum clock frequency VCC = 3.3V 350 MHz C I Input capacitance 5.0 pF C Power dissipation capacitanceper flip flop V = GND to VCC 1 Outputs enabled 16 pFC PD Pow er dissipation capacitance per flip-flop VI = GND to VCC 1 Outputs disabled 10 pF NOTE: 1. CPD is used to determine the dynamic power dissipation (PD in W): PD = CPD × VCC 2 × fi + (CL × VCC 2 × fo) where: fi = input frequency in MHz; CL = output load capacitance in pF; fo = output frequency in MHz; VCC = supply voltage in V; (CL × VCC 2 × fo) = sum of outputs.

ORDERING INFORMATION

PACKAGES TEMPERATURE RANGE OUTSIDE NORTH AMERICA NORTH AMERICA DWG NUMBER 48-Pin Plastic SSOP Type III –40°C to +85°C 74ALVCH16374 DL ACH16374 DL SOT370-1 48-Pin Plastic TSSOP Type II –40°C to +85°C 74ALVCH16374 DGG ACH16374 DGG SOT362-1

Philips Semiconductors Product specification 74ALVCH1637416-bit edge-triggered D-type flip-flop (3-State)

1998 Jun 18 3

PIN NUMBER SYMBOL NAME AND FUNCTION 1 1OE Output enable input (active LOW) 2, 3, 5, 6, 8, 9, 11, 12 1Q0 to 1Q7 3-State flip-flop outputs 4, 10, 15, 21, 28, 34, 39, 45 GND Ground (0V) 7, 18, 31, 42 VCC Positive supply voltage 13, 14, 16, 17, 19, 20, 22, 23 2Q0 to 2Q7 3-State flip-flop outputs 24 2OE Output enable input (active LOW) 25 2CP Clock input 36, 35, 33, 32, 30, 29, 27, 26 2D0 to 2D7 Data inputs 47, 46, 44, 43, 41, 40, 38, 37 1D0 to 1D7 Data inputs 48 1CP Clock input LOGIC SYMBOL 1OE 2OE 1CP 2CP 1D0 1D1 1D2 1D3 1D4 1D5 1D6 1D7 2D0 2D1 2D2 2D3 2D4 2D5 2D6 2D7 1Q0 1Q1 1Q2 1Q3 1Q4 1Q5 1Q6 1Q7 2Q0 2Q1 2Q2 2Q3 2Q4 2Q5 2Q6 2Q7 48 25 241 SW00075 LOGIC DIAGRAM DQ CP FF1 1D0 1CP 1OE 1Q0 TO 7 OTHER CHANNELS DQ CP FF9 2D0 2CP 2OE 2Q0 TO 7 OTHER CHANNELS SW00076 FUNCTION TABLE OPERATING MODES INPUTS INTERNAL OUTPUTS OPERATING MODES OE CP Dn FLIP-FLOPS Q0 to Q7 Load and read register L L l h L H L H Load register and disable outputs H H l h L H Z Z H = HIGH voltage level h = HIGH voltage level one set-up time prior to the HIGH-to-LOW LE transition L = LOW voltage level l = LOW voltage level one set-up time prior to the HIGH-to-LOW LE transition Z = high impedance OFF-state = LOW-to-HIGH CP transition

Philips Semiconductors Product specification 74ALVCH1637416-bit edge-triggered D-type flip-flop (3-State)

1998 Jun 18 4

LOGIC SYMBOL (IEEE/IEC) SW00199 1EN 1 ∇ 2EN 2 ∇2D 1OE 1CLK 2OE 2CLK 1D0 1D1 1D2 1D3 1D4 1D5 1D6 2D0 2D1 2D2 2D3 2D4 2D5 2D6 2D7 1Q0 1Q1 1Q2 1Q3 1Q4 1Q5 1Q6 1Q7 2Q0 2Q1 2Q2 2Q3 2Q4 2Q7 1D7 2Q5 2Q6 BUS HOLD CIRCUIT To internal circuit VCC Data Input SW00044 RECOMMENDED OPERATING CONDITIONS SYMBOL PARAMETER CONDITIONS LIMITS UNITSYMBOL PARAMETER CONDITIONS MIN MAX UNIT DC supply voltage 2.5V range (for max. speed performance @ 30 pF output load) 2.3 2.7 VCC DC supply voltage 3.3V range (for max. speed performance @ 50 pF output load) 3.0 3.6 V DC supply voltage (for low-voltage applications) 1.2 3.6 V DC Input voltage range For data input pins 0 VCC VVI DC Input voltage range For control pins 0 5.5 V VO DC output voltage range 0 VCC V Tamb Operating free-air temperature range –40 +85 °C tr, tf Input rise and fall times VCC = 2.3 to 3.0V VCC = 3.0 to 3.6V ns/V

Philips Semiconductors Product specification 74ALVCH1637416-bit edge-triggered D-type flip-flop (3-State)

1998 Jun 18 5

In accordance with the Absolute Maximum Rating System (IEC 134) Voltages are referenced to GND (ground = 0V) SYMBOL PARAMETER CONDITIONS RATING UNIT VCC DC supply voltage –0.5 to +4.6 V IIK DC input diode current VI /C01160 –50 mA VI DC input voltage For control pins1 –0.5 to +4.6 VVI DC in ut voltage For data inputs1 –0.5 to VCC +0.5 V IOK DC output diode current VO /C0117VCC or VO /C0116 0 /C003450 mA VO DC output voltage Note 1 –0.5 to VCC +0.5 V IO DC output source or sink currentVO = 0 to VCC /C003450 mA IGND , ICC DC V CC or GND current /C0034100 mA Tstg Storage temperature range –65 to +150 °C PTOT Power dissipation per package –plastic medium-shrink (SSOP) –plastic thin-medium-shrink (TSSOP) For temperature range: –40 to +125 °C above +55°C derate linearly with 11.3 mW/K above +55°C derate linearly with 8 mW/K 850 600 mW NOTE: 1. The input and output voltage ratings may be exceeded if the input and output current ratings are observed. DC ELECTRICAL CHARACTERISTICS Over recommended operating conditions. Voltage are referenced to GND (ground = 0 V). LIMITS SYMBOL PARAMETER TEST CONDITIONS Temp = -40°C to +85°C UNIT MIN TYP 1 MAX VCC = 1.2V VCC V HIGH level Input voltage VCC = 1.8V 0.7*VCC 0.9 VVIH HIGH level Input voltage VCC = 2.3 to 2.7V 1.7 1.2 V VCC = 2.7 to 3.6V 2.0 1.5 VCC = 1.2V GND V LOW level Input voltage VCC = 1.8V 0.9 0.2*VCC VVIL LOW level Input voltage VCC = 2.3 to 2.7V 1.2 0.7 V VCC = 2.7 to 3.6V 1.5 0.8 VCC =18t o36 V;V =V or V ;IO = 100 µA VCC 02 VCCVCC = 1.8 to 3.6V; VI = VIH or VIL; IO = –100µA VCC /C00420.2 VCC VCC = 1.8V; VI = VIH or VIL; IO = –6mA VCC /C00420.4 VCC /C00420.10 VCC = 2.3V; VI = VIH or VIL; IO = –6mA VCC /C00420.3 VCC /C00420.08 VOH HIGH level output voltage VCC = 2.3V; VI = VIH or VIL; IO = –12mA VCC /C00420.5 VCC /C00420.17 V VCC = 2.3V; VI = VIH or VIL; IO = –18mA VCC /C00420.6 VCC /C00420.26 VCC = 2.7V; VI = VIH or VIL; IO = –12mA VCC /C00420.5 VCC /C00420.14 VCC = 3.0V; VI = VIH or VIL; IO = –24mA VCC /C00421.0 VCC /C00420.28

Philips Semiconductors Product specification 74ALVCH1637416-bit edge-triggered D-type flip-flop (3-State)

1998 Jun 18 6

DC ELECTRICAL CHARACTERISTICS (Continued) Over recommended operating conditions. Voltage are referenced to GND (ground = 0 V). LIMITS SYMBOL PARAMETER TEST CONDITIONS Temp = -40°C to +85°C UNIT MIN TYP 1 MAX V =18t o36 V; V =V or V ;I = 100µA GND 02 0VCC = 1.8 to 3.6V; VI = VIH or VIL; IO = 100µA GND 0.20 VCC = 1.8V; VI = VIH or VIL; IO = 6mA 0.09 0.30 VCC = 2.3V; VI = VIH or VIL; IO = 6mA 0.07 0.20 VOL LOW level output voltage VCC = 2.3V; VI = VIH or VIL; IO = 12mA 0.15 0.40 V VCC = 2.3V; VI = VIH or VIL; IO = 12mA 0.23 0.60 VCC = 2.7V; VI = VIH or VIL; IO = 12mA 0.14 0.40 VCC = 3.0V; VI = VIH or VIL; IO = 24mA 0.27 0.55 I Input leakage current per control pin VCC = 1.8 to 3.6V; VI = 5.5V or GND 0.1 5 µAII Input leakage current per dataVCC = 1.8 to 3.6V; 01 5 µA g pin CC VI = VCC or GND 0.1 5 I /I Input current for common I/OVCC = 1.8 to 2.7V; VI = VCC or GND 0.1 10 µAIIHZ/IILZ pins VCC = 3.6V; VI = VCC or GND 0.1 15 µA IO 3-State output OFF-state VCC = 1.8 to 2.7V; VI = VIH or VIL; VO = VCC or GND 0.1 5 µA IOZ current VCC = 2.7 to 3.6V; VI = VIH or VIL; VO = VCC or GND 0.1 10 µA ICC Quiescent supply current VCC = 1.8 to 2.7V; VI = VCC or GND; IO = 0 0.1 20 µAICC Q uiescent supply current VCC = 2.7 to 3.6V; VI = VCC or GND; IO = 0 0.2 40 µA ΔICC Additional quiescent supply current given per control pin VCC = 2 7V to 3 6V;V =V CC 06 V;IO =0 5 500 µAΔICC Additional quiescent supply current given per data I/O pin VCC = 2.7V to 3.6V; VI = VCC – 0.6V; IO = 0 150 750 µA I 2 Bus hold LOW sustaining VCC = 2.3V; VI = 0.7V 45 – µAIBHL 2 g current VCC = 3.0V; VI = 0.8V 75 150 µA I 2 Bus hold HIGH sustaining VCC = 2.3V; VI = 1.7V –45 µAIBHH 2 g current VCC = 3.0V; VI = 2.0V –75 –175 µA I O 2 Bus hold LOW overdrive VCC = 2.7V 300 µAIBHLO 2 current VCC = 3.6V 450 µA I O 2 Bus hold HIGH overdrive VCC = 2.7V –300 µAIBHHO 2 current VCC = 3.6V –450 µA NOTES: 1. All typical values are at Tamb = 25°C. 2. Valid for data inputs of bus hold parts.

Philips Semiconductors Product specification 74ALVCH1637416-bit edge-triggered D-type flip-flop (3-State)

1998 Jun 18 7

AC CHARACTERISTICS FOR V CC = 2.3V TO 2.7V RANGE AND VCC < 2.3V GND = 0V; tr = tf ≤ 2.0ns; CL = 30pF LIMITS SYMBOL PARAMETER WAVEFORM VCC = 2.3 to 2.7V VCC = 1.8V VCC = 1.2V UNIT MIN TYP 1, 2 MAX MIN TYP 1 MAX TYP1 tPHL /tPLH Propagation delay tPZH /tPZL 3-State output enable time nOE to nQn tPHZ /tPLZ 3-State output disable time nOE to nQn tW nCP pulse width HIGH or LOW tsu Set-up time Dn to nCP 3 1.2 0.2 – 1.5 0.2 – – ns th Hold time Dn to nCP 3 0.8 –0.1 – 0.6 –0.2 – – ns fmax Maximum clock pulse frequency 1 150 300 – 125 250 – – MHz NOTES: 1. All typical values are measured at Tamb = 25°C. 2. Typical value is measured at VCC = 2.5V. AC CHARACTERISTICS FOR V CC = 3.0V TO 3.6V RANGE AND VCC = 2.7V GND = 0V; tr = tf ≤ 2.5ns; CL = 50pF LIMITS SYMBOL PARAMETER WAVEFORM VCC = 2.3 to 2.7V VCC = 2.7V UNIT MIN TYP 1, 2 MAX MIN TYP 1 MAX tPHL /tPLH Propagation delay tPZH /tPZL 3-State output enable time nOE to nQn tPHZ /tPLZ 3-State output disable time nOE to nQn tW nCP pulse width HIGH or LOW 1 2.5 1.4 – 3.0 1.6 – ns tsu Set-up time Dn to nCP 3 1.2 0.2 – 1.5 0.4 – ns th Hold time Dn to nCP 3 0.8 0.0 – 0.6 –0.2 – ns fmax Maximum clock pulse frequency 1 200 350 – 150 300 – MHz NOTES: 1. All typical values are measured at Tamb = 25°C. 2. Typical value is measured at VCC = 3.3V.

Philips Semiconductors Product specification 74ALVCH1637416-bit edge-triggered D-type flip-flop (3-State)

1998 Jun 18 8

AC WAVEFORMS FOR V CC = 2.3V TO 2.7V AND VCC < 2.3V RANGE VM = 0.5 VCC VX = VOL + 0.15V VY = VOH –0.15V VOL and VOH are the typical output voltage drop that occur with the output load. VI = VCC AC WAVEFORMS FOR V CC = 3.0V TO 3.6V AND VCC = 2.7V RANGE VM = 1.5 V VX = VOL + 0.3V VY = VOH –0.3V VOL and VOH are the typical output voltage drop that occur with the output load. VI = 2.7V VM VM 1/fMAX tw tPHL tPLH CP INPUT Qn OUTPUT SW00078 GND VOH VOL VI Waveform 1. Clock (CP) to output (Qn) propagation delays, the clock pulse width and the maximum clock pulse frequency tPLZ tPZL VI OE INPUT GND VCC OUTPUT LOW-to-OFF OFF-to-LOW VOL VOH OUTPUT HIGH-to-OFF OFF-to-HIGH GND outputs enabled outputs enabled outputs disabled tPHZ VM VM VM tPZH VX VY SW00072 VM Waveform 2. 3-State enable and disable times VM SW00079 VI GND ÉÉÉÉ ÉÉÉÉ ÉÉÉÉ ÉÉÉÉÉÉÉ ÉÉÉÉÉÉÉ ÉÉÉÉÉÉÉ ÉÉ ÉÉ ÉÉ ÉÉ ÉÉ ÉÉ VM Dn INPUT VI GND VM VOH Qn OUTPUT V OL CP INPUT tsu th tsu th NOTE: The shaded areas indicate when the input is permitted to change for predictable output performance. Waveform 3. Data set-up and hold times for the Dn input to the CP input TEST CIRCUIT SWITCH POSITION PULSE GENERATOR R T VI D.U.T. VO C L VCC R L = 500 Ω Test Circuit for switching times Open GND DEFINITIONS VCC VI < 2.7V V CC TEST S 1 tPLH/tPHL Open R L = Load resistor C L = Load capacitance includes jig and probe capacitance R T = Termination resistance should be equal to ZOUT of pulse generators. 2 /C0060 VCCtPLZ/tPZL 2.7V2.7–3.6V tPHZ/tPZH GND R L = 500 Ω 2 * VCC SV00906 Waveform 4. Load circuitry for switching times

Philips Semiconductors Product specification 74ALVCH163742.5V/3.3V 16-bit edge-triggered D-type flip-flop (3-State)

1998 Jun 18 9

SSOP48: plastic shrink small outline package; 48 leads; body width 7.5 mm SOT370-1

Philips Semiconductors Product specification 74ALVCH163742.5V/3.3V 16-bit edge-triggered D-type flip-flop (3-State)

1998 Jun 18 10

TSSOP48: plastic thin shrink small outline package; 48 leads; body width 6.1mm SOT362-1

Philips Semiconductors Product specification 74ALVCH163742.5V/3.3V 16-bit edge-triggered D-type flip-flop (3-State)

1998 Jun 18 11

Philips Semiconductors Product specification 74ALVCH163742.5V/3.3V 16-bit edge-triggered D-type flip-flop (3-State)

1998 Jun 18 12

Philips Semiconductors and Philips Electronics North America Corporation reserve the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. LIFE SUPPORT APPLICATIONS Philips Semiconductors and Philips Electronics North America Corporation Products are not designed for use in life support appliances, devices, or systems where malfunction of a Philips Semiconductors and Philips Electronics North America Corporation Product can reasonably be expected to result in a personal injury. Philips Semiconductors and Philips Electronics North America Corporation customers using or selling Philips Semiconductors and Philips Electronics North America Corporation Products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors and Philips Electronics North America Corporation for any damages resulting from such improper use or sale. This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips Semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. Philips Semiconductors

811 East Arques Avenue

P.O. Box 3409 Sunnyvale, California 94088–3409 Telephone 800-234-7381 DEFINITIONS Data Sheet Identification Product Status Definition Objective Specification Preliminary Specification Product Specification Formative or in Design Preproduction Product Full Production This data sheet contains the design target or goal specifications for product development. Specifications may change in any manner without notice. This data sheet contains Final Specifications. Philips Semiconductors reserves the right to make changes at any time without notice, in order to improve design and supply the best possible product.  Copyright Philips Electronics North America Corporation 1998 All rights reserved. Printed in U.S.A. Date of release: 06-98 Document order number: 9397-750-04542 /C0109 /C0110 /C0114