74ALVCH162245 PHILIPS

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 11

Technical content

/C0109 /C0110 /C0114 74ALVCH162245 16-bit bus transceiver with direction pin and 30Ω termination resistor (3-State) Product specification 1998 Jun 29 INTEGRATED CIRCUITS IC24 Data Handbook

Philips Semiconductors Product specification 74ALVCH16224516-bit bus transceiver with direction pin and 30Ω termination resistor (3-State)

21998 Jun 29 853-2085 19638

FEATURES

  • Wide supply voltage range of 1.2V to 3.6V
  • Complies with JEDEC standard no. 8-1A
  • CMOS low power consumption
  • MULTIBYTE TM flow-through standard pin-out architecture
  • Low inductance multiple VCC and ground pins for minimum noise and ground bounce
  • Direct interface with TTL levels
  • Bus hold on all data inputs
  • Integrated 30Ω termination resistor

DESCRIPTION

The 74ALVCH162245 is a 16-bit transceiver featuring non-inverting 3-State bus compatible outputs in both send and receive directions. The 74ALVCH162245 features two output enable (nOE) inputs for easy cascading and two send/receive (nDIR) inputs for direction control. nOE controls the outputs so that the buses are effectively isolated. This device can be used as two 8-bit transceivers or one 16-bit transceiver. The 74ALVCH162245 is designed with 30Ω series resistors in both HIGH and LOW output states. The 74ALVCH162245 has active bus hold circuitry which is provided to hold unused or floating data inputs at a valid logic level. This feature eliminates the need for external pull-up or pull-down resistors. PIN CONFIGURATION 20 29 GND V CC1 GND GND VCC1 2A5 2A4 VCC2 2A3 2A2 GND 2A1 2A0 1A7 1A6 GND 1A5 1A4 VCC2 1A3 1A2 GND 1A1 1A0 1OE 24 25 28GND 2DIR 2OE 2A7 2A6 GND SW00198 1DIR 1B0 1B1 1B2 1B3 1B4 1B5 1B6 1B7 2B0 2B1 2B2 2B3 2B4 2B5 2B6 2B7 QUICK REFERENCE DATA GND = 0V; Tamb = 25°C; tr = tf ≤ 2.5ns SYMBOL PARAMETER CONDITIONS TYPICAL UNIT tPHL /tPLH Propagation delay An to Bn; Bn to An VCC = 2.5V, CL = 30pF VCC = 3.3V, CL = 50pF 2.4 ns C I Input capacitance 4.0 pF C I/O Input/output capacitance 8.0 pF C Power dissipation capacitanceper buffer V = GND to VCC 1 Outputs enabled 27 pF C PD Pow er dissipation capacitance per buffer VI = GND to VCC 1 Outputs disabled 4 pF NOTES: 1. CPD is used to determine the dynamic power dissipation (PD in µW): PD = CPD × VCC 2 × fi + (CL × VCC 2 × fo) where: fi = input frequency in MHz; CL = output load capacitance in pF; fo = output frequency in MHz; VCC = supply voltage in V; (CL × VCC 2 × fo) = sum of the outputs.

ORDERING INFORMATION

PACKAGES TEMPERATURE RANGE OUTSIDE NORTH AMERICA NORTH AMERICA DWG NUMBER 48-Pin Plastic SSOP Type III –40°C to +85°C 74ALVCH162245 DL ACH162245 DL SOT370-1 48-Pin Plastic TSSOP Type II –40°C to +85°C 74ALVCH162245 DGG ACH162245 DGG SOT362-1

Philips Semiconductors Product specification 74ALVCH16224516-bit bus transceiver with direction pin and 30Ω termination resistor (3-State)

1998 Jun 29 3

PIN NUMBER SYMBOL NAME AND FUNCTION 1 1DIR Direction control 2, 3, 5, 6, 8, 9, 11, 12 1B0 to 1B7 Data inputs/outputs 4, 10, 15, 21, 28, 34, 39, 45 GND Ground (0V) 7, 18, 31, 42 VCC Positive supply voltage 13, 14, 16, 17, 19, 20, 22, 23 2B0 to 2B7 Data inputs/outputs 24 2DIR Direction control 25 2OE Output enable input (active LOW) 36, 35, 33, 32, 30, 29, 27, 26 2A0 to 2A7 Data inputs/outputs 47, 46, 44, 43, 41, 40, 38, 37 1A0 to 1A7 Data inputs/outputs 48 1OE Output enable input (active LOW) LOGIC SYMBOL 2DIR 24 26 23 2OE 2A0 2A1 2A2 2A3 2A4 2A5 2A6 2A7 2B0 2B1 2B2 2B3 2B4 2B5 2B6 2B7 1DIR 37 12 1OE 1A0 1A1 1A2 1A3 1A4 1A5 1A6 1A7 1B0 1B1 1B2 1B3 1B4 1B5 1B6 1B7 SW00197 FUNCTION TABLE INPUTS INPUTS/OUTPUT nOE nDIR nAn nBn L L A = B inputs L H inputs B = A H X Z Z H = HIGH voltage level L = LOW voltage level X = don’t care Z = high impedance OFF–state LOGIC SYMBOL (IEEE/IEC)

3 EN1 [BA]

6 EN4 [BA]

3 EN2 [AB]

6 EN5 [AB]

Philips Semiconductors Product specification 74ALVCH16224516-bit bus transceiver with direction pin and 30Ω termination resistor (3-State)

1998 Jun 29 4

RECOMMENDED OPERATING CONDITIONS SYMBOL PARAMETER CONDITIONS LIMITS UNITSYMBOL PARAMETER CONDITIONS MIN MAX UNIT VCC DC supply voltage 2.5V range (for max. speed performance @ 30 pF output load) 2.3 2.7 VVCC DC supply voltage 3.3V range (for max. speed performance @ 50 pF output load) 3.0 3.6 V VI DC Input voltage range 0 VCC V VO DC output voltage range 0 VCC V Tamb Operating free-air temperature range –40 +85 °C tr, tf Input rise and fall times VCC = 2.3 to 3.0V VCC = 3.0 to 3.6V ns/V ABSOLUTE MAXIMUM RATINGS In accordance with the Absolute Maximum Rating System (IEC 134) Voltages are referenced to GND (ground = 0V) SYMBOL PARAMETER CONDITIONS RATING UNIT VCC DC supply voltage –0.5 to +4.6 V IIK DC input diode current VI 0 –50 mA VI DC input voltage For data inputs with bus hold1 –0.5 to VCC +0.5 VVI DC in ut voltage For control pins1 –0.5 to +4.6 V IOK DC output diode current VO VCC or VO 0 50 mA VO DC output voltage Note 1 –0.5 to VCC +0.5 V IO DC output source or sink currentVO = 0 to VCC 50 mA IGND , ICC DC V CC or GND current 100 mA Tstg Storage temperature range –65 to +150 °C PTOT Power dissipation per package –plastic medium-shrink (SSOP) –plastic thin-medium-shrink (TSSOP) For temperature range: –40 to +125 °C above +55°C derate linearly with 11.3 mW/K above +55°C derate linearly with 8 mW/K 850 600 mW NOTE: 1. The input and output voltage ratings may be exceeded if the input and output current ratings are observed.

Philips Semiconductors Product specification 74ALVCH16224516-bit bus transceiver with direction pin and 30Ω termination resistor (3-State)

1998 Jun 29 5

DC ELECTRICAL CHARACTERISTICS Over recommended operating conditions. Voltage are referenced to GND (ground = 0 V). LIMITS SYMBOL PARAMETER TEST CONDITIONS Temp = -40°C to +85°C UNIT MIN TYP 1 MAX V HIGH level Input voltage VCC = 2.3 to 2.7V 1.7 1.2 VVIH HIGH level Input voltage VCC = 2.7 to 3.6V 2.0 1.5 V V LOW level Input voltage VCC = 2.3 to 2.7V 1.2 0.7 VVIL LOW level Input voltage VCC = 2.7 to 3.6V 1.5 0.8 V VCC =23t o36 V;V =V or V ;IO = 100 µA VCC 02 VCCVCC = 2.3 to 3.6V; VI = VIH or VIL; IO = –100µA VCC /C00420.2 VCC VCC = 2.3V; VI = VIH or VIL; IO = –4mA VCC /C00420.4 VCC /C00420.11 VCC = 2.3V; VI = VIH or VIL; IO = –6mA VCC /C00420.6 VCC /C00420.17 VOH HIGH level output voltage VCC = 2.7V; VI = VIH or VIL; IO = –4mA VCC /C00420.5 VCC /C00420.09 V VCC = 2.7V; VI = VIH or VIL; IO = –8mA VCC /C00420.7 VCC /C00420.19 VCC = 3.0V; VI = VIH or VIL; IO = –6mA VCC /C00420.6 VCC /C00420.13 VCC = 3.0V; VI = VIH or VIL; IO = –12mA VCC /C00421.0 VCC /C00420.27 V =23t o36 V; V =V or V ;I = 100µA GND 02 0VCC = 2.3 to 3.6V; VI = VIH or VIL; IO = 100µA GND 0.20 VCC = 2.3V; VI = VIH or VIL; IO = 4mA 0.07 0.40 VCC = 2.3V; VI = VIH or VIL; IO = 6mA 0.11 0.55 VOL LOW level output voltage VCC = 2.7V; VI = VIH or VIL; IO = 4mA 0.06 0.40 V VCC = 2.7V; VI = VIH or VIL; IO = 8mA 0.13 0.60 VCC = 3.0V; VI = VIH or VIL; IO = 6mA 0.09 0.55 VCC = 3.0V; VI = VIH or VIL; IO = 12mA 0.19 0.80 Input leakage currentper datapin VCC =23t o36 V;II Input leakage current per data pin with bus hold VCC = 2.3 to 3.6V; V V or GND 0.1 5 µAI w ith bus hold VI = VCC or GND µ IOZ 3-State output OFF-state currentVCC = 2.3 to 3.6V; VI = VIH or VIL; VO = VCC or GND 0.1 10 µA ICC Quiescent supply current VCC = 2.3 to 3.6V; VI = VCC or GND; IO = 0 0.2 40 µA ΔICC Additional quiescent supply current given per data I/O pin with bus holdVCC = 2.3V to 3.6V; VI = VCC – 0.6V; IO = 0 150 750 µA I 2 Bus hold LOW sustaining current VCC = 2.3V; VI = 0.7V 45 – µAIBHL 2 Bus hold LOW sustaining current VCC = 3.0V; VI = 0.8V 75 150 µA I 2 Bus hold HIGH sustaining current VCC = 2.3V; VI = 1.7V –45 µAIBHH 2 Bus hold HIGH sustaining current VCC = 3.0V; VI = 2.0V –75 –175 µA IBHLO 2 Bus hold LOW overdrive currentVCC = 3.6V 500 µA IBHHO 2 Bus hold HIGH overdrive currentVCC = 3.6V –500 µA NOTES: 1. All typical values are at Tamb = 25°C. 2. Valid for data inputs of bus hold parts.

Philips Semiconductors Product specification 74ALVCH16224516-bit bus transceiver with direction pin and 30Ω termination resistor (3-State)

1998 Jun 29 6

AC CHARACTERISTICS FOR V CC = 2.3V TO 2.7V RANGE GND = 0V; tr = tf ≤ 2.0ns; CL = 30pF LIMITS SYMBOL PARAMETER WAVEFORM VCC = 2.3 to 2.7V UNIT MIN TYP 1, 2 MAX tPHL /tPLH Propagation delay nAn to nBn; nBn to nAn 1, 3 1.0 2.5 4.9 ns tPZH /tPZL 3-State output enable time nOE to nAn; nOE to nBn 2, 3 1.0 2.9 6.8 ns tPHZ /tPLZ 3-State output disable time nOE to nAn; nOE to nBn 2, 3 1.0 3.0 6.3 ns NOTES: 1. All typical values are measured Tamb = 25°C. 2. Typical value is measured at VCC = 2.5V AC CHARACTERISTICS FOR V CC = 3.0V TO 3.6V RANGE AND VCC = 2.7V GND = 0V; tr = tf ≤ 2.5ns; CL = 50pF LIMITS SYMBOL PARAMETER WAVEFORM VCC = 3.3 ± 0.3V VCC = 2.7V UNIT MIN TYP 1, 2 MAX MIN TYP 1 MAX tPHL /tPLH Propagation delay tPZH /tPZL 3-State output enable time nOE tPHZ /tPLZ 3-State output disable time nOE NOTES: 1. All typical values are measured Tamb = 25°C. 2. Typical value is measured at VCC = 3.3V

Philips Semiconductors Product specification 74ALVCH16224516-bit bus transceiver with direction pin and 30Ω termination resistor (3-State)

1998 Jun 29 7

AC WAVEFORMS FOR V CC = 2.3V TO 2.7V AND VCC < 2.3V RANGE VM = 0.5 VCC VX = VOL + 0.15V VY = VOH –0.15V VOL and VOH are the typical output voltage drop that occur with the output load. VI = VCC AC WAVEFORMS FOR V CC = 3.0V TO 3.6V AND VCC = 2.7V RANGE VM = 1.5 V VX = VOL + 0.3V VY = VOH –0.3V VOL and VOH are the typical output voltage drop that occur with the output load. VI = 2.7V SW00063 An, Bn INPUT VM tPHL tPLH VOL VI VM GND VOH Bn, An OUTPUT Waveform 1. Input (nAn, nBn) to output (nBn, nAn) propagation delay times tPLZ tPZL VI OE INPUT GND VCC OUTPUT LOW-to-OFF OFF-to-LOW VOL VOH OUTPUT HIGH-to-OFF OFF-to-HIGH GND outputs enabled outputs enabled outputs disabled tPHZ VM VM VM tPZH VX VY SW00064 Waveform 2. 3-State enable and disable times TEST CIRCUIT SWITCH POSITION PULSE GENERATOR R T VI D.U.T. VO C L VCC R L = 500 Ω Test Circuit for switching times Open GND DEFINITIONS VCC VI < 2.7V V CC TEST S 1 tPLH/tPHL Open R L = Load resistor C L = Load capacitance includes jig and probe capacitance R T = Termination resistance should be equal to ZOUT of pulse generators. 2 /C0060 VCCtPLZ/tPZL 2.7V2.7–3.6V tPHZ/tPZH GND R L = 500 Ω 2 * VCC SV00906 Waveform 3. Load circuitry for switching times

Philips Semiconductors Product specification 74ALVCH16224516-bit bus transceiver with direction pin and 30Ω termination resistor (3-State)

1998 Jun 29 8

SSOP48: plastic shrink small outline package; 48 leads; body width 7.5 mm SOT370-1

Philips Semiconductors Product specification 74ALVCH16224516-bit bus transceiver with direction pin and 30Ω termination resistor (3-State)

1998 Jun 29 9

TSSOP48: plastic thin shrink small outline package; 48 leads; body width 6.1mm SOT362-1

Philips Semiconductors Product specification 74ALVCH16224516-bit bus transceiver with direction pin and 30Ω termination resistor (3-State)

1998 Jun 29 10

Philips Semiconductors Product specification 74ALVCH16224516-bit bus transceiver with direction pin and 30Ω termination resistor (3-State) yyyy mmm dd 11 Definitions Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Disclaimers Life support — These products are not designed for use in life support appliances, devices or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes — Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Philips Semiconductors

811 East Arques Avenue

P.O. Box 3409 Sunnyvale, California 94088–3409 Telephone 800-234-7381  Copyright Philips Electronics North America Corporation 1998 All rights reserved. Printed in U.S.A. Date of release: 06-98 Document order number: 9397-750-04539 /C0109 /C0110 /C0114 Data sheet status Objective specification Preliminary specification Product specification Product status Development Qualification Production Definition [1] This data sheet contains the design target or goal specifications for product development. Specification may change in any manner without notice. This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips Semiconductors reserves the right to make chages at any time without notice in order to improve design and supply the best possible product. This data sheet contains final specifications. Philips Semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. Data sheet status [1] Please consult the most recently issued datasheet before initiating or completing a design.