74ALVC244 PHILIPS
Document overview
- Manufacturer or author: Provided By digicamel.com
- PDF pages: 15
Technical content
Product specification Supersedes data of 2003 Aug 11
2003 Sep 08
Octal buffer/line driver; 3-state
2003 Sep 08 2
Philips Semiconductors Product specification Octal buffer/line driver; 3-state 74ALVC244
FEATURES
- Wide supply voltage range from 1.65 to 3.6 V
- 3.6 V tolerant inputs/outputs
- CMOS low power consumption
- Direct interface with TTL levels (2.7 to 3.6 V)
- Power-down mode
- Latch-up performance exceeds 250 mA
- Complies with JEDEC standard: JESD8-7 (1.65 to 1.95 V) JESD8-5 (2.3 to 2.7 V) JESD8B/JESD36 (2.7 to 3.6 V)
- ESD protection: HBM EIA/JESD22-A114-A exceeds 2000 V MM EIA/JESD22-A115-A exceeds 200 V.
DESCRIPTION
The 74ALVC244 is a high-performance, low-power, low-voltage, Si-gate CMOS device and superior to most advanced CMOS compatible TTL families. The 74ALVC244 is an octal non-inverting buffer/line driver with 3-state outputs. The 3-state outputs are controlled by the output enable inputs 1 OE and 2OE. A HIGH on nOE causes the outputs to assume a high-impedance OFF-state. Schmitt-trigger action at all inputs makes the circuit highly tolerant for slower input rise and fall times. QUICK REFERENCE DATA GND = 0 V; T amb =2 5°C. Notes 1. C PD is used to determine the dynamic power dissipation (PD inµW). PD =C PD × VCC 2 × fi× N+ Σ(CL × VCC 2 × fo) where: fi= input frequency in MHz; fo = output frequency in MHz; C L = output load capacitance in pF; VCC = supply voltage in Volts; N = total load switching outputs; Σ(C L × VCC 2 × fo) = sum of the outputs. 2. The condition is VI= GND to VCC . SYMBOL PARAMETER CONDITIONS TYPICAL UNIT tPHL /tPLH propagation delay nAn to nYn V CC = 1.8 V; CL = 30 pF; RL =1k Ω 2.7 ns VCC = 2.5 V; CL = 30 pF; RL = 500Ω 2.0 ns VCC = 2.7 V; CL = 50 pF; RL = 500Ω 2.3 ns VCC = 3.3 V; CL = 50 pF; RL = 500Ω 2.2 ns C I input capacitance 3.5 pF C PD power dissipation capacitance per buffer VCC = 3.3 V; notes 1 and 2 20 pF
2003 Sep 08 3
Philips Semiconductors Product specification Octal buffer/line driver; 3-state 74ALVC244 FUNCTION TABLE See note 1. Note 1. H = HIGH voltage level; L = LOW voltage level; X = don’t care; Z = high-impedance OFF-state.
ORDERING INFORMATION
n OE nAn nYn LLL LHH HXZ TYPE NUMBER PACKAGE TEMPERATURE RANGE PINS PACKAGE MATERIAL CODE 74ALVC244D −40 to +85°C 20 SO20 plastic SOT163-1 74ALVC244PW −40 to +85°C 20 TSSOP20 plastic SOT360-1 74ALVC244BQ −40 to +85°C 20 DHVQFN20 plastic SOT764-1 PINNING PIN SYMBOL DESCRIPTION
11 OE output enable input (active LOW)
10 GND ground (0 V)
OE output enable input (active LOW)
20 V CC supply voltage
2003 Sep 08 4
Philips Semiconductors Product specification Octal buffer/line driver; 3-state 74ALVC244 handbook, halfpage 1OE 1A0 2Y0 1A1 2Y1 1A2 2Y2 1A3 2Y3 GND VCC 2OE 1Y0 2A0 2A1 1Y2 1Y1 2A2 1Y3 2A3 10 11 244 MNA162 Fig.1 Pin configuration. handbook, halfpage 1A0 2Y0 1A1 2Y1 1A2 2Y2 1A3 2Y3 2OE 1Y0 2A0 1Y1 2A1 1Y2 2A2 1Y3 1OE VCC 10 11 GNDTop view 2A3 GND (1) MNA981 Fig.2 Logic symbol. (1) The die substrate is attached to this pad using conductive die attach material. It can not be used as a supply pin or input. handbook, halfpage MNA168 1A3 1A2 1A1 1A02 1Y0 1Y1 1Y2 1Y3 1OE 2A3 2A2 2A1 2A017 2Y0 2Y1 2Y2 2Y3 2OE Fig.3 Logic symbol. handbook, halfpage 1 EN MNA169 19 EN Fig.4 IEE/IEC logic symbol.
2003 Sep 08 5
Philips Semiconductors Product specification Octal buffer/line driver; 3-state 74ALVC244 handbook, halfpage MNA170 1A3 1A2 1A1 1A0 1Y0 1Y1 1Y2 1Y3 1OE 2A3 2A2 2A1 2A0 2Y0 2Y1 2Y2 2Y3 2OE Fig.5 Logic diagram.
2003 Sep 08 6
Philips Semiconductors Product specification Octal buffer/line driver; 3-state 74ALVC244 RECOMMENDED OPERATING CONDITIONS LIMITING VALUES In accordance with the Absolute Maximum Rating System (IEC 60134); voltages are referenced to GND (ground = 0 V). Notes 1. The input and output voltage ratings may be exceeded if the input and output current ratings are observed. 2. When V CC = 0 V (Power-down mode), the output voltage can be 3.6 V in normal operation. 3. For SO20 packages: above 70°C derate linearly with 8 mW/K. For TSSOP20 packages: above 60°C derate linearly with 5.5 mW/K. For DHVQFN20 packages: above 60°C derate linearly with 4.5 mW/K. SYMBOL PARAMETER CONDITIONS MIN. MAX. UNIT VCC supply voltage 1.65 3.6 V VI input voltage 0 3.6 V VO output voltage V CC = 1.65 to 3.6 V; enable mode 0 V CC V VCC = 1.65 to 3.6 V; disable mode 0 3.6 V VCC = 0 V; Power-down mode 0 3.6 V Tamb operating ambient temperature −40 +85 °C tr,tf input rise and fall times V CC = 1.65 to 2.7 V 0 20 ns/V VCC = 2.7 to 3.6 V 0 10 ns/V SYMBOL PARAMETER CONDITIONS MIN. MAX. UNIT VCC supply voltage −0.5 +4.6 V IIK input diode current V I<0 −− 50 mA VI input voltage −0.5 +4.6 V IOK output diode current V O >V CC or VO <0 −± 50 mA VO output voltage enable mode; notes 1 and 2 −0.5 V CC + 0.5 V disable mode −0.5 +4.6 V Power-down mode; note 2 −0.5 +4.6 V IO output source or sink current VO =0t oVCC −± 50 mA IGND , ICC VCC or GND current −± 100 mA Tstg storage temperature −65 +150 °C Ptot power dissipation T amb = −40 to +85°C; note 3 − 500 mW
2003 Sep 08 7
Philips Semiconductors Product specification Octal buffer/line driver; 3-state 74ALVC244 DC CHARACTERISTICS At recommended operating conditions; voltages are referenced to GND (ground=0V ) . Notes 1. All typical values are measured at Tamb =2 5°C. 2. For transceivers, the parameters IOZ includes the input leakage current. SYMBOL PARAMETER TEST CONDITIONS MIN. TYP. (1) MAX. UNIT OTHER V CC (V) Tamb = −40 to +85°C VIH HIGH-level input voltage 1.65 to 1.95 0.65× VCC −− V 2.7 to 3.6 2 −− V VIL LOW-level input voltage 1.65 to 1.95−− 0.35× VCC V VOL LOW-level output voltage VI=V IH or VIL IO = 100µA 1.65 to 3.6 −− 0.2 V IO = 6 mA 1.65 −− 0.3 V IO =1 2m A 2 . 3 −− 0.4 V IO =1 8m A 2 . 3 −− 0.6 V IO =1 2m A 2 . 7 −− 0.4 V IO =1 8m A 3 . 0 −− 0.4 V IO =2 4m A 3 . 0 −− 0.55 V VOH HIGH-level output voltage VI=V IH or VIL IO = −100 µA 1.65 to 3.6 V CC − 0.2 −− V IO = −6 mA 1.65 1.25 −− V IO = −12 mA 2.3 1.8 −− V IO = −18 mA 2.3 1.7 −− V IO = −12 mA 2.7 2.2 −− V IO = −18 mA 3.0 2.4 −− V IO = −24 mA 3.0 2.2 −− V ILI input leakage current VI= 3.6 V or GND 3.6 −± 0.1 ±5 µA IOZ 3-state output OFF-state current VI=V IH or VIL; VO = 3.6 V or GND; note 2 3.6 − 0.1 ±10 µA Ioff power OFF leakage current VIor VO = 3.6 V 0.0 −± 0.1 ±10 µA ICC quiescent supply current VI=V CC or GND; IO = 0 3.6 − 0.2 20 µA ΔICC additional quiescent supply current per input pin V I=V CC − 0.6 V; IO = 0 3.0 to 3.6 − 5 750 µA
2003 Sep 08 8
Philips Semiconductors Product specification Octal buffer/line driver; 3-state 74ALVC244 AC CHARACTERISTICS Note 1. All typical values are measured at Tamb =2 5°C. AC WAVEFORMS SYMBOL PARAMETER TEST CONDITIONS MIN. TYP. (1) MAX. UNIT WAVEFORMS V CC (V) Tamb = −40 to +85°C 2.7 1.0 2.3 3.1 ns t PZH /tPZL 3-state output enable time nOE to nYn 2.7 1.0 3.2 5.3 ns tPHZ /tPLZ 3-state output disable time nOE to nYn 2.7 1.0 3.0 4.4 ns handbook, halfpage MNA171 nAn input nYn output tPLH tPHL GND VI VM VM VM VM VOH VOL Fig.6 Input nAn to output nYn propagation delay times. VCC VM INPUT VI tr =tf 1.65 to 1.95 V 0.5× VCC VCC ≤ 2.0 ns 2.3 to 2.7 V 0.5 × VCC VCC ≤ 2.0 ns 2.7 V 1.5 V 2.7 V ≤ 2.5 ns
2003 Sep 08 9
Philips Semiconductors Product specification Octal buffer/line driver; 3-state 74ALVC244 handbook, full pagewidth MNA654 tPLZ tPHZ outputs disabled outputs enabled Vy Vx outputs enabled output LOW-to-OFF OFF-to-LOW output HIGH-to-OFF OFF-to-HIGH nOE input VI VCC VM VOL VOH GND GND tPZL tPZH VM VM Fig.7 3-state enable and disable times. VCC VM INPUT VI tr =tf 1.65 to 1.95 V 0.5× VCC VCC ≤ 2.0 ns 2.3 to 2.7 V 0.5× VCC VCC ≤ 2.0 ns 2.7 V 1.5 V 2.7 V ≤ 2.5 ns VX =V OL + 0.3 V at VCC ≥ 2.7 V; VX =V OL + 0.15 V at VCC < 2.7 V; VY =V OH − 0.3 V at VCC ≥ 2.7 V; VY =V OH − 0.15 V at VCC < 2.7 V.
2003 Sep 08 10
Philips Semiconductors Product specification Octal buffer/line driver; 3-state 74ALVC244 handbook, full pagewidth VEXT VCC VI VO MNA616 D.U.T. C LR T R L R L PULSE GENERATOR Fig.8 Load circuitry for switching times. Definitions for test circuit: R L = Load resistor. C L = Load capacitance including jig and probe capacitance. R T = Termination resistance should be equal to the output impedance Zo of the pulse generator. VCC VI C L R L VEXT tPLH /tPHL tPZH /tPHZ tPZL /tPLZ 1.65 to 1.95 V VCC 30 pF 1 k Ω open GND 2 × VCC 2.3 to 2.7 V V CC 30 pF 500 Ω open GND 2 × VCC 2.7 V 2.7 V 50 pF 500 Ω open GND 6 V 3.0 to 3.6 V 2.7 V 50 pF 500 Ω open GND 6 V
2003 Sep 08 11
Philips Semiconductors Product specification Octal buffer/line driver; 3-state 74ALVC244 PACKAGE OUTLINES UNIT A max. A 1 A 2 A 3 bp cD (1) E (1) (1)eH E LL p Q Zywv q REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA mm inches 2.65 0.3 0.1 2.45 2.25 0.49 0.36 0.32 0.23 13.0 12.6 7.6 7.4 1.27 10.65 10.00 1.1 1.0 0.9 0.4 8 o o 0.25 0.1 DIMENSIONS (inch dimensions are derived from the original mm dimensions) Note 1. Plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included. 1.1 0.4 SOT163-1 w M bp detail X Z e D y 0.25 075E04 MS-013 pin 1 index 0.1 0.012 0.004 0.096 0.089 0.019 0.014 0.013 0.009 0.51 0.49 0.30 0.29 0.05 1.4 0.0550.419 0.394 0.043 0.039 0.035 0.0160.01 0.25 0.01 0.0040.043 0.0160.01 0 5 10 mm scale X q AA 1 A 2 H E Lp Q E c L v M A (A )3 A SO20: plastic small outline package; 20 leads; body width 7.5 mm SOT163-1 99-12-27 03-02-19
2003 Sep 08 12
Philips Semiconductors Product specification Octal buffer/line driver; 3-state 74ALVC244 UNIT A 1 A 2 A 3 bp cD (1) E (2) (1)eH E LL p QZ ywv q REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA mm 0.15 0.05 0.95 0.80 0.30 0.19 0.2 0.1 6.6 6.4 4.5 4.3 0.65 6.6 6.2 0.4 0.3 0.5 0.2 o o0.13 0.10.21 DIMENSIONS (mm are the original dimensions) Notes 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. Plastic interlead protrusions of 0.25 mm maximum per side are not included. 0.75 0.50 SOT360-1 MO-153 99-12-27 03-02-19 w M bp D Z e 0.25 11 0 20 11 pin 1 index q AA 1 A 2 Lp Q detail X L (A )3 H E E c v M A XA y 0 2.5 5 mm scale TSSOP20: plastic thin shrink small outline package; 20 leads; body width 4.4 mm SOT360-1 A max. 1.1
2003 Sep 08 13
Philips Semiconductors Product specification Octal buffer/line driver; 3-state 74ALVC244 terminal 1 index area 0.51 A 1 EhbUNIT ye 0.2 c REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA mm 4.6 4.4 D h 3.15 2.85 2.6 2.4 1.15 0.85 3.50.30 0.18 0.05 0.00 0.05 0.1 DIMENSIONS (mm are the original dimensions) 0.5 0.3 L 0.1 v 0.05 w 0 2.5 5 mm scale SOT764-1 DHVQFN20: plastic dual in-line compatible thermal enhanced very thin quad flat package; no leads; 20 terminals; body 2.5 x 4.5 x 0.85 mm A (1) max. A c detail X yy1 Ce L Eh D h e b 19 12 101 X D E C B A terminal 1 index area AC C Bv M w M E (1) Note 1. Plastic or metal protrusions of 0.075 mm maximum per side are not included. D (1) 02-10-17 03-01-27
2003 Sep 08 14
Philips Semiconductors Product specification Octal buffer/line driver; 3-state 74ALVC244 DATA SHEET STATUS Notes 1. Please consult the most recently issued data sheet before initiating or completing a design. 2. The product status of the device(s) described in this data sheet may have changed since this data sheet was 3. For data sheets describing multiple type numbers, the highest-level product status determines the data sheet status. LEVEL DATA SHEET STATUS (1) PRODUCT STATUS (2)(3) DEFINITION I Objective data Development This data sheet contains data from the objective specification for product development. Philips Semiconductors reserves the right to change the specification in any manner without notice. II Preliminary data Qualification This data sheet contains data from the preliminary specification. Supplementary data will be published at a later date. Philips Semiconductors reserves the right to change the specification without notice, in order to improve the design and supply the best possible product. III Product data Production This data sheet contains data from the product specification. Philips Semiconductors reserves the right to make changes at any time in order to improve the design, manufacturing and supply. Relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN). DEFINITIONS Short-form specification The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 60134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. DISCLAIMERS Life support applications These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes Philips Semiconductors reserves the right to make changes in the products - including circuits, standard cells, and/or software - described or contained herein in order to improve design and/or performance. When the product is in full production (status ‘Production’), relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN). Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no licence or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified.
© Koninklijke Philips Electronics N.V. 2003 SCA75 All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights. Philips Semiconductors – a worldwide company Contact information For additional information please visit http://www.semiconductors.philips.com. Fax: +31 40 27 24825 Printed in The Netherlands R20/03/pp15 Date of release:2003 Sep 08 Document order number: 9397 750 12018