74ALVC164245 NXP

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 20

Technical content

  1. General description The 74ALVC164245 is a high-performance, low-power, low-voltage, Si-gate CMOS device, superior to most advanced CMOS compatible TTL families. The 74ALVC164245 is a 16-bit (dual octal) dual supply translating transceiver featuring non-inverting 3-state bus compatible outputs in both send and receive directions. It is designed to interface between a 3 V and 5 V bus in a mixed 3 V and 5 V supply environment. This device can be used as two 8-bit transceivers or one 16-bit transceiver. The direction control inputs (1DIR and 2DIR) determine the direction of the data flow. nDIR (active HIGH) enables data from nAn ports to nBn ports. nDIR (active LOW) enables data from nBn ports to nAn ports. The output enable inputs (1OE and 2OE), when HIGH, disable both nAn and nBn ports by placing them in a high-impedance OFF-state. Pins nAn, nOE and nDIR are referenced to VCC(A) and pins nBn are referenced to VCC(B). In suspend mode, when one of the supply voltages is zero, there will be no current flow from the non-zero supply towards the zero supply. The nAn-outputs must be set 3-state and the voltage on the A-bus must be smaller than V diode (typical 0.7 V). VCC(B) ≥ VCC(A) (except in suspend mode). 2. Features and benefits „ 5 V tolerant inputs/outputs for interfacing with 5 V logic „ Wide supply voltage range: ‹ 3 V port (VCC(A)): 1.5 V to 3.6 V ‹ 5 V port (VCC(B)): 1.5 V to 5.5 V „ CMOS low power consumption „ Direct interface with TTL levels „ Control inputs voltage range from 2.7 V to 5.5 V „ Inputs accept voltages up to 5.5 V „ High-impedance outputs when VCC(A) or VCC(B) = 0 V „ Complies with JEDEC standard JESD8-B/JESD36 „ ESD protection: ‹ HBM JESD22-A114F exceeds 2000 V ‹ MM JESD22-A115-A exceeds 200 V „ Specified from −40 °C to +85 °C and −40 °C to +125 °C 74ALVC164245 16-bit dual supply translating transceiver; 3-state Rev. 05 — 13 April 2010 Product data sheet

Table 1. Ordering information

Product data sheet Rev. 05 — 13 April 2010 3 of 20 NXP Semiconductors 74ALVC164245 16-bit dual supply translating transceiver; 3-state Fig 2. IEC logic symbol 3EN1[BA] 6EN1[BA] 3EN2[AB] 6EN2[AB] 1A0 2A1 2A0 2A2 2A3 2A4 2A5 2A6 2A7 2B1 2B2 2B3 2B4 2B5 2B6 2B7 1OE 1DIR 001aaa790 1A1 1A2 1A3 1A4 1A5 1A6 1A7 1B0 2B0 1B1 1B2 1B3 1B4 1B5 1B6 1B7 2OE 2DIR

Product data sheet Rev. 05 — 13 April 2010 4 of 20 NXP Semiconductors 74ALVC164245 16-bit dual supply translating transceiver; 3-state 5. Pinning information

5.1 Pinning

Fig 3. Pin configuration SOT370-1 (SSOP48) and SOT362-1 (TSSOP48) 74ALVC164245 1DIR 1OE 1B0 1A0 1B1 1A1 GND GND 1B2 1A2 1B3 1A3 V CC(B) VCC(A) 1B4 1A4 1B5 1A5 GND GND 1B6 1A6 1B7 1A7 2B0 2A0 2B1 2A1 GND GND 2B2 2A2 2B3 2A3 V CC(B) VCC(A) 2B4 2A4 2B5 2A5 GND GND 2B6 2A6 2B7 2A7 2DIR 2OE 001aab037

Product data sheet Rev. 05 — 13 April 2010 5 of 20 NXP Semiconductors 74ALVC164245 16-bit dual supply translating transceiver; 3-state (1) The die substrate is attached to this pad using conductive die attach material. It can not be used as a supply pin or input. Fig 4. Pin configuration SOT1134-1 (HXQFN60U) D3A16A15A14A13A12A11D2 B9 B10 D7 A17 A18 B11 A19 B12 A20 B13 A21 B14 B8A10 D6 A22 B15 A23 B16 A24 B17 A25 A26D8 D4A27 B18 A28A29 B19B20 A30A31A32 74ALVC164245 001aai851 Transparent top view GND(1) terminal 1 index area

5.2 Pin description

[1] H = HIGH voltage level; L = LOW voltage level; X = don’t care; Z = high-impedance OFF-state. Table 2. Pin description Table 3. Function table [1] Table 4. Limiting values

temperatures which are detrimental to reliability. The maximum junction temperature of this integrated circuit should not exceed 150 °C. [2] The input and output voltage ratings may be exceeded if the input and output current ratings are observed. tot derates linearly with 5.5 mW/K. [4] Above 70 °C the value of Ptot derates linearly with 1.8 mW/K.

  1. Recommended operating conditions

Table 4. Limiting values …continued Table 5. Recommended operating conditions

Table 6. Static characteristics At recommended operating conditions; voltages are referenced to GND (ground = 0 V).

[1] All typical values are measured at V CC(B) = 5.0 V, VCC(A) = 3.3 V and Tamb =2 5 °C. [2] If V CC(A) < 2.7 V, the switching levels at all inputs are not TTL compatible. [3] For transceivers, the parameter I OZ includes the input leakage current. Table 6. Static characteristics …continued At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Table 7. Dynamic characteristics GND = 0 V; tr = tf ≤ 2.5 ns; CL = 50 pF; for test circuit see Figure 7.

Table 7. Dynamic characteristics …continued GND = 0 V; tr = tf ≤ 2.5 ns; CL = 50 pF; for test circuit see Figure 7.

[1] All typical values are measured at nominal voltage for V CC(B) and VCC(A) and at Tamb =2 5 °C. [2] t pd is the same as tPLH and tPHL. ten is the same as tPZL and tPZH. tdis is the same as tPLZ and tPHZ. [3] C PD is used to determine the dynamic power dissipation (PD in μW). L × VCC2 × fo) = sum of outputs. [4] The condition is V I = GND to VCC.

5 V port: nAn to nBn;

3 V port: nBn to nAn;

GND = 0 V; tr = tf ≤ 2.5 ns; CL = 50 pF; for test circuit see Figure 7. Measurement points are given in Table 8. VOL and VOH are typical output voltage levels that occur with the output load.

Measurement points are given in Table 8. VOL and VOH are typical output voltage levels that occur with output load. Table 8. Measurement points

Test data is given in Table 9. RT = Termination resistance should be equal to output impedance Zo of the pulse generator. CL = Load capacitance including jig and probe capacitance. Table 9. Test data

Product data sheet Rev. 05 — 13 April 2010 14 of 20 NXP Semiconductors 74ALVC164245 16-bit dual supply translating transceiver; 3-state 12. Package outline Fig 8. Package outline SOT370-1 (SSOP48) UNIT A 1 A2 A3 bp cD (1) E (1) eH E LL p QZ ywv θ REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA mm 0.4 0.2 2.35 2.20 0.25 0.3 0.2 0.22 0.13 16.00 15.75 7.6 10.1 1.0 0.6 1.2 1.0 0.85 0.40 o o0.18 0.1 DIMENSIONS (mm are the original dimensions) Note 1. Plastic or metal protrusions of 0.25 mm maximum per side are not included. SOT370-1 99-12-27 03-02-19 (1) w M bp D HE E Z e c v M A X A y 48 25 MO-118 241 θ AA1 Lp Q detail X L (A )3 pin 1 index 0 5 10 mm scale SSOP48: plastic shrink small outline package; 48 leads; body width 7.5 mm SOT370-1 A max. 2.8

Product data sheet Rev. 05 — 13 April 2010 15 of 20 NXP Semiconductors 74ALVC164245 16-bit dual supply translating transceiver; 3-state Fig 9. Package outline SOT362-1 (TSSOP48) UNIT A 1 A2 A3 bp cD (1) E(2) eH E LL p QZ ywv θ REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA mm 0.15 0.05 0.2 0.1 o o0.1 DIMENSIONS (mm are the original dimensions). Notes 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. Plastic interlead protrusions of 0.25 mm maximum per side are not included. SOT362-1 99-12-27 03-02-19 w M θ AA1 D Lp Q detail X E Z e c L X (A )3 0.25 12 4 48 25 y pin 1 index b H 1.05 0.85 0.28 0.17 0.2 0.1 12.6 12.4 6.2 6.0 0.5 1 0.258.3 7.9 0.50 0.35 0.8 0.40.080.8 0.4 p E v M A A TSSOP48: plastic thin shrink small outline package; 48 leads; body width 6.1 mm SOT362-1 A max. 1.2 0 2.5 5 mm scale MO-153

Product data sheet Rev. 05 — 13 April 2010 16 of 20 NXP Semiconductors 74ALVC164245 16-bit dual supply translating transceiver; 3-state Fig 10. Package outline SOT1134-1 (HXQFN60U) ReferencesOutline version European projection Issue date IEC JEDEC JEITA sot1134-1_po 08-12-17 09-01-22 Unit mm max nom min 0.50 0.48 0.46 0.05 0.02 0.00 4.1 4.0 3.9 1.90 1.85 1.80 6.1 6.0 5.9 3.90 3.85 3.80 1 2.5 4.5 0.125 0.075 0.025 0.07 A Dimensions HXQFN60U: plastic thermal enhanced extremely thin quad flat package; no leads; 60 terminals; UTLP based; body 4 x 6 x 0.5 mm SOT1134-1 A1 b 0.35 0.30 0.25 DD h EE h 0.08 0.1 yy 1e 0.5 e1 e2 e3 e4 eR 0.5 k 0.25 0.20 0.15 L 0.35 0.30 0.25 L 1 v 0.05 w 0 2.5 5 mm scale AC Bv Cw B A terminal 1 index area D E C yCy1 X detail X A A1 eR e3 e4 e e 1/2 e 1/2 e b AC Bv Cw k L B20 B18 A27 D4A32 D7D6 D3D2 Dh Eh terminal 1 index area A11 A16 B10B8 A17 B11 B17 A26A1 A10

Table 10. Abbreviations Table 11. Revision history

  • 74ALVC164245BQ changed from HUQFN60U (SOT1025-1) to HXQFN60U (SOT1134-1) package. 74ALVC164245_4 20081111 Product data sheet - 74ALVC 164245_3 Modifications: • Added type number 74ALVC164245 (HUQFN60U package) 74ALVC164245_3 20040914 Product data sheet - 74ALVC164245_2 74ALVC164245_2 20040601 Product data sheet - 74ALVC164245_1 74ALVC164245_1 19980826 Product specification - -

Product data sheet Rev. 05 — 13 April 2010 18 of 20 NXP Semiconductors 74ALVC164245 16-bit dual supply translating transceiver; 3-state 15. Legal information

15.1 Data sheet status

[1] Please consult the most recently issued document before initiating or completing a design. [2] The term ‘short data sheet’ is explained in section “Definitions”. [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com.

15.2 Definitions

Draft — The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet — A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. Product specification — The information and data provided in a Product data sheet shall define the specification of the product as agreed between NXP Semiconductors and its customer, unless NXP Semiconductors and customer have explicitly agreed otherwise in writing. In no event however, shall an agreement be valid in which the NXP Semiconductors product is deemed to offer functions and qualities beyond those described in the Product data sheet.

15.3 Disclaimers

Limited warranty and liability — Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. In no event shall NXP Semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Notwithstanding any damages that customer might incur for any reason whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of NXP Semiconductors. Right to make changes — NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use in automotive applications — This NXP Semiconductors product has been qualified for use in automotive applications. The product is not designed, authorized or warranted to be suitable for use in medical, military, aircraft, space or life support equipment, nor in applications where failure or malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors accepts no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk. Applications — Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. NXP Semiconductors does not accept any liability related to any default, damage, costs or problem which is based on a weakness or default in the customer application/use or the application/use of customer’s third party customer(s) (hereinafter both referred to as “Application”). It is customer’s sole responsibility to check whether the NXP Semiconductors product is suitable and fit for the Application planned. Customer has to do all necessary testing for the Application in order to avoid a default of the Application and the product. NXP Semiconductors does not accept any liability in this respect. Limiting values — Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the device. Limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the Recommended operating conditions section (if present) or the Characteristics sections of this document is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. Terms and conditions of commercial sale — NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms , unless otherwise agreed in a valid written individual agreement. In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. NXP Semiconductors hereby expressly objects to applying the customer’s general terms and conditions with regard to the purchase of NXP Semiconductors products by customer. No offer to sell or license — Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. Export control — This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from national authorities.

15.4 Trademarks

Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This docu ment contains the product specification.

Product data sheet Rev. 05 — 13 April 2010 19 of 20 NXP Semiconductors 74ALVC164245 16-bit dual supply translating transceiver; 3-state 16. Contact information For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com

NXP Semiconductors 74ALVC164245 16-bit dual supply translating transceiver; 3-state © NXP B.V. 2010. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com Date of release: 13 April 2010 Document identifier: 74ALVC164245_5 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section ‘Legal information’. 17. Contents