74ALVC16244 NEXPERIA

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 13

Technical content

Datasheet sections

potentially damaging backflow current through the device when it is powered down.

  • Wide supply voltage range from 1.2 V to 3.6 V
  • CMOS low power consumption
  • MultiByte flow-through standard pin-out architecture
  • Low inductance multiple VCC and GND pins for minimum noise and ground bounce
  • Overvoltage tolerant inputs to 5.5 V
  • Direct interface with TTL levels
  • IOFF circuitry provides partial Power-down mode operation
  • All data inputs have bushold (74ALVCH16244 only)
  • Latch-up performance exceeds 100 mA per JESD 78 Class II Level B
  • Complies with JEDEC standards:
  • JESD8-7 (1.65 V to 1.95 V)
  • JESD8-5 (2.3 V to 2.7 V)
  • JESD8C (2.7 V to 3.6 V)
  • Output drive capability 50 Ω transmission lines at 85 °C
  • Current drive ±24 mA at 3.0 V
  • ESD protection:
  • HBM JESD22-A114-A exceeds 2000 V
  • MM JESD22-A115-A exceeds 200 V 3. Ordering information

Table 1. Ordering information

Nexperia 74ALVC16244; 74ALVCH16244 2.5 V / 3.3 V 16-bit buffer/line driver; 3-state 4. Functional diagram 1A0 1A1 1A2 1A3 1OE 1Y0 1Y1 1Y2 1Y3 3A0 3A1 3A2 3A3 3OE 3Y0 3Y1 3Y2 3Y3 mna996 2A0 2A1 2A2 2A3 2OE 2Y0 2Y1 2Y2 2Y3 4A0 4A1 4A2 4A3 4OE 4Y0 4Y1 4Y2 4Y3 Fig. 1. Logic symbol 001aae231 1A0 1A1 1A2 1A3 2A0 2A1 2A2 2A3 3A0 3A1 3A2 3A3 4A0 4A1 4A2 4A3 1Y0 1Y1 1Y2 1Y3 2Y0 2Y1 2Y2 2Y3 3Y0 3Y1 3Y2 3Y3 4Y0 4Y1 4Y2 4Y3 4OE 1OE 2OE 3OE EN1 EN2 EN3 EN4 Fig. 2. IEC logic symbol to internal circuit mna705 VCC data input Fig. 3. Bus hold circuit 74ALVC_ALVCH16244 All information provided in this document is subject to legal disclaimers. © Nexperia B.V. 2021. All rights reserved Product data sheet Rev. 6 — 22 July 2021 2 / 13

Table 2. Pin description

Table 3. Function table H = HIGH voltage level; L = LOW voltage level; X = don’t care; Z = high-impedance OFF-state. Table 4. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V). [1] The input and output voltage ratings may be exceeded if the input and output current ratings are observed.

  1. Recommended operating conditions

Table 5. Recommended operating conditions Table 6. Static characteristics

Nexperia 74ALVC16244; 74ALVCH16244 2.5 V / 3.3 V 16-bit buffer/line driver; 3-state Symbol Parameter Conditions Min Typ[1] Max Unit 74ALVCH16244; data inputs; VI = VCC or GND; VCC = 1.8 V to 3.6 V - 0.1 5 μA 74ALVC16244; data inputs; VI = 5.5 V or GND; VCC = 1.8 V to 3.6 V - 0.1 5 μA II input leakage current control inputs; VI = 5.5 V or GND; VCC = 1.8 V to 3.6 V - 0.1 5 μA VCC = 2.3 V; VI = 0.7 V [2] 45 - - μAIBHL bus hold LOW current VCC = 3.0 V; VI = 0.8 V [2] 75 150 - μA VCC = 2.3 V; VI = 1.7 V [2] -45 - - μAIBHH bus hold HIGH current VCC = 3.0 V; VI = 2.0 V [2] -75 -175 - μA VCC = 2.7 V [2] 300 - - μAIBHLO bus hold LOW overdrive current VCC = 3.6 V [2] 450 - - μA VCC = 2.7 V [2] -300 - - μAIBHHO bus hold HIGH overdrive current VCC = 3.6 V [2] -450 - - μA VCC = 1.8 to 2.7 V; VI = VIH or VIL; VO = VCC or GND - 0.1 5 μAIOZ OFF-state output current VCC = 3.6 V; VI = VIH or VIL; VO = VCC or GND - 0.1 10 μA VCC = 1.8 to 2.7 V; VI = VCC or GND; IO = 0 A - 0.1 20 μAICC supply current VCC = 2.3 to 3.6 V; VI = VCC or GND; IO = 0 A - 0.2 40 μA per input pin; VI = VCC - 0.6 V; IO = 0 A; VCC = 2.7 V to 3.6 V 74ALVCH16244; data inputs - 150 750 μA 74ALVC16244; data inputs - 5 500 μA ΔICC additional supply current control pins - 5 500 μA CI input capacitance - 5.0 - pF [1] All typical values are measured at Tamb = 25 °C. [2] Valid for data inputs of bus hold parts. 74ALVC_ALVCH16244 All information provided in this document is subject to legal disclaimers. © Nexperia B.V. 2021. All rights reserved Product data sheet Rev. 6 — 22 July 2021 6 / 13

Table 7. Dynamic characteristics Voltages are referenced to GND (ground = 0 V). For test circuit, see Fig. 7. [2] tpd is the same as tPHL and tPLH. [3] ten is the same as tPZH and tPZL. [4] tdis is the same as tPHZ and tPLZ. [5] CPD is used to determine the dynamic power dissipation (PD in μW).

Measurement points are given in Table 8. VOL and VOH are typical voltage output levels that occur with the output load. Measurement points are given in Table 8. VOL and VOH are typical voltage output levels that occur with the output load. Table 8. Measurement points

Test data is given in Table 9. CL = Load capacitance including jig and probe capacitance. RT = Termination resistance should be equal to output impedance Zo of the pulse generator. VEXT = External voltage for measuring switching times. Table 9. Test data

Nexperia 74ALVC16244; 74ALVCH16244 2.5 V / 3.3 V 16-bit buffer/line driver; 3-state 11. Package outline ReferencesOutline version European projection Issue date IEC JEDEC JEITA SOT362-1 MO-153 sot362-1_po 03-02-19 13-08-05 Unit mm max nom min 0.15 0.28 0.2 12.6 0.5 0.8 A Dimensions (mm are the original dimensions) Note 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. Plastic interlead protrusions of 0.25 mm maximum per side are not included. TSSOP48: plastic thin shrink small outline package; 48 leads; body width 6.1 mm SOT362-1 A1 A2 1.05 A3 bp c D(1) θE(2) e HE L Lp Q v w y Z 8.3 0.86.2 0.50 pin 1 index v A θ A D Lp Q E Z c L 1 24 48 25 e w y X A HE bp detail X (A3) 0 5 mm scale 2.5 Fig. 8. Package outline SOT362-1 (TSSOP48) 74ALVC_ALVCH16244 All information provided in this document is subject to legal disclaimers. © Nexperia B.V. 2021. All rights reserved Product data sheet Rev. 6 — 22 July 2021 10 / 13

Table 10. Abbreviations Table 11. Revision history Modifications: • Type number 74ALVC16244DL (SOT370-1/SSOP48) removed.

  • Section 1 and Section 2 updated.
  • Section 7: derating values for Ptot total power dissipation updated. 74ALVC_ALVCH16244 v.5 20190115 Product data sheet - 74ALVC_ALVCH16244 v.4 Modifications: • Type number 74ALVCH16244DL (SOT370-1) removed. 74ALVC_ALVCH16244 v.4 20170612 Product data sheet - 74ALVC_ALVCH16244 v.3 Modifications: • The format of this data sheet has been redesigned to comply with the identity guidelines of Nexperia.
  • Legal texts have been adapted to the new company name where appropriate. 74ALVC_ALVCH16244 v.3 20030514 Product specification - 74ALVC_ALVCH16244 v.2 74ALVC_ALVCH16244 v.2 19980629 Product specification - 74ALVCH16244 v.1 74ALVCH16244 v.1 19970321 Product specification - - 74ALVC_ALVCH16244 All information provided in this document is subject to legal disclaimers. © Nexperia B.V. 2021. All rights reserved Product data sheet Rev. 6 — 22 July 2021 11 / 13

Nexperia 74ALVC16244; 74ALVCH16244 2.5 V / 3.3 V 16-bit buffer/line driver; 3-state 14. Legal information Data sheet status Document status [1][2] Product status [3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification. [1] Please consult the most recently issued document before initiating or completing a design. [2] The term 'short data sheet' is explained in section "Definitions". [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the internet at https://www.nexperia.com. Definitions Draft — The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. Nexperia does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet — A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local Nexperia sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. Product specification — The information and data provided in a Product data sheet shall define the specification of the product as agreed between Nexperia and its customer, unless Nexperia and customer have explicitly agreed otherwise in writing. In no event however, shall an agreement be valid in which the Nexperia product is deemed to offer functions and qualities beyond those described in the Product data sheet. Disclaimers Limited warranty and liability — Information in this document is believed to be accurate and reliable. However, Nexperia does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. Nexperia takes no responsibility for the content in this document if provided by an information source outside of Nexperia. In no event shall Nexperia be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Notwithstanding any damages that customer might incur for any reason whatsoever, Nexperia’s aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of Nexperia. Right to make changes — Nexperia reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use — Nexperia products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or malfunction of an Nexperia product can reasonably be expected to result in personal injury, death or severe property or environmental damage. Nexperia and its suppliers accept no liability for inclusion and/or use of Nexperia products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk. Quick reference data — The Quick reference data is an extract of the product data given in the Limiting values and Characteristics sections of this document, and as such is not complete, exhaustive or legally binding. Applications — Applications that are described herein for any of these products are for illustrative purposes only. Nexperia makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Customers are responsible for the design and operation of their applications and products using Nexperia products, and Nexperia accepts no liability for any assistance with applications or customer product design. It is customer’s sole responsibility to determine whether the Nexperia product is suitable and fit for the customer’s applications and products planned, as well as for the planned application and use of customer’s third party customer(s). Customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. Nexperia does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer’s applications or products, or the application or use by customer’s third party customer(s). Customer is responsible for doing all necessary testing for the customer’s applications and products using Nexperia products in order to avoid a default of the applications and the products or of the application or use by customer’s third party customer(s). Nexperia does not accept any liability in this respect. Limiting values — Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the device. Limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the Recommended operating conditions section (if present) or the Characteristics sections of this document is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. Terms and conditions of commercial sale — Nexperia products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nexperia.com/profile/terms, unless otherwise agreed in a valid written individual agreement. In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. Nexperia hereby expressly objects to applying the customer’s general terms and conditions with regard to the purchase of Nexperia products by customer. No offer to sell or license — Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. Export control — This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from competent authorities. Non-automotive qualified products — Unless this data sheet expressly states that this specific Nexperia product is automotive qualified, the product is not suitable for automotive use. It is neither qualified nor tested in accordance with automotive testing or application requirements. Nexperia accepts no liability for inclusion and/or use of non-automotive qualified products in automotive equipment or applications. In the event that customer uses the product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall use the product without Nexperia’s warranty of the product for such automotive applications, use and specifications, and (b) whenever customer uses the product for automotive applications beyond Nexperia’s specifications such use shall be solely at customer’s own risk, and (c) customer fully indemnifies Nexperia for any liability, damages or failed product claims resulting from customer design and use of the product for automotive applications beyond Nexperia’s standard warranty and Nexperia’s product specifications. Translations — A non-English (translated) version of a document is for reference only. The English version shall prevail in case of any discrepancy between the translated and English versions. Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. 74ALVC_ALVCH16244 All information provided in this document is subject to legal disclaimers. © Nexperia B.V. 2021. All rights reserved Product data sheet Rev. 6 — 22 July 2021 12 / 13