74ALVC125 PHILIPS

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 16

Technical content

Product specification 2002 Nov 18 INTEGRATED CIRCUITS 74ALVC125 Quad buffer/line driver; 3-state

2002 Nov 18 2

Philips Semiconductors Product specification Quad buffer/line driver; 3-state 74ALVC125

FEATURES

  • Wide supply voltage range from 1.65 to 3.6 V
  • Complies with JEDEC standard: JESD8-7 (1.65 to 1.95 V) JESD8-5 (2.3 to 2.7 V) JESD8B/JESD36 (2.7 to 3.6 V)
  • 3.6 V tolerant inputs/outputs
  • CMOS low power consumption
  • Direct interface with TTL levels (2.7 to 3.6 V)
  • Power-down mode
  • Latch-up performance exceeds 250 mA
  • ESD protection: HBM EIA/JESD22-A114-A exceeds 2000 V MM EIA/JESD22-A115-A exceeds 200 V.

DESCRIPTION

The 74ALVC125 is a high-performance, low-power, low-voltage, Si-gate CMOS device and superior to most advanced CMOS compatible TTL families. Schmitt-trigger action at all inputs makes the circuit tolerant for slower input rise and fall times. The 74ALVC125 consists of four non-inverting buffer/line drivers with 3-state outputs. The 3-state outputs (nY) are controlled by the output enable input (n OE). A HIGH on pin nOE causes the outputs to assume a high-impedance OFF-state. QUICK REFERENCE DATA GND = 0 V; Tamb =2 5°C. Notes 1. C PD is used to determine the dynamic power dissipation (PD inµW). PD =C PD × VCC 2 × fi× N+ Σ(CL × VCC 2 × fo) where: fi= input frequency in MHz; fo = output frequency in MHz; C L = output load capacitance in pF; VCC = supply voltage in Volts; N = total switching outputs; Σ(C L × VCC 2 × fo) = sum of the outputs. 2. The condition is VI= GND to VCC . SYMBOL PARAMETER CONDITIONS TYPICAL UNIT tPHL /tPLH propagation delay inputs nA to output nY VCC = 1.8 V; CL = 30 pF; RL =1k Ω 2.4 ns VCC = 2.5 V; CL = 30 pF; RL = 500Ω 1.7 ns VCC = 2.7 V; CL = 50 pF; RL = 500Ω 2.0 ns VCC = 3.3 V; CL = 50 pF; RL = 500Ω 1.8 ns C I input capacitance 3.5 pF C PD power dissipation capacitance per buffer VCC = 3.3 V; notes 1 and 2 outputs enable 27 pF outputs disabled 5 pF

2002 Nov 18 3

Philips Semiconductors Product specification Quad buffer/line driver; 3-state 74ALVC125

ORDERING INFORMATION

See note 1. Note 1. H = HIGH voltage level; L = LOW voltage level; X = don’t care; Z = high-impedance OFF-state. PINNING TYPE NUMBER PACKAGE PINS PACKAGE MATERIAL CODE 74ALVC125D 14 SO14 plastic SOT108-1 74ALVC125PW 14 TSSOP14 plastic SOT402-1 INPUT OUTPUT n OE nA nY LLL LHH HXZ PIN SYMBOL DESCRIPTION

11 OE output enable input (active LOW)

OE output enable input (active LOW) 5 2A data input 6 2Y bus output

7 GND ground (0 V)

OE output enable input (active LOW) 11 4Y bus output 12 4A data input 13 4 OE output enable input (active LOW)

14 V CC supply voltage

2002 Nov 18 4

Philips Semiconductors Product specification Quad buffer/line driver; 3-state 74ALVC125 MNA226 125 7 8 1OE 2OE GND 3Y 3OE 4OE VCC Fig.1 Pin configuration. handbook, halfpage MNA227 nOE nA nY Fig.2 Logic diagram (one buffer). handbook, halfpage MNA229

1 EN1

Fig.3 IEE/IEC logic symbol. Fig.4 Logic symbol. handbook, halfpage MNA228 1A 1Y2 1OE 2A 2Y5 2OE 3A 3Y9 3OE 4A 4Y12 4OE

2002 Nov 18 5

Philips Semiconductors Product specification Quad buffer/line driver; 3-state 74ALVC125 RECOMMENDED OPERATING CONDITIONS LIMITING VALUES In accordance with the Absolute Maximum Rating System (IEC 60134); voltages are referenced to GND (ground = 0 V). Notes 1. The input and output voltage ratings may be exceeded if the input and output current ratings are observed. 2. When V CC = 0 V (Power-down mode), the output voltage can be 3.6 V in normal operation. SYMBOL PARAMETER CONDITIONS MIN. MAX. UNIT VCC supply voltage 1.65 3.6 V VI input voltage 0 3.6 V VO output voltage V CC = 1.65 to 3.6 V; enable mode 0 V CC V VCC = 1.65 to 3.6 V; disable mode 0 3.6 V VCC = 0 V; Power-down mode 0 3.6 V Tamb operating ambient temperature −40 +85 °C tr,tf input rise and fall times V CC = 1.65 to 2.7 V 0 20 ns/V VCC = 2.7 to 3.6 V 0 10 ns/V SYMBOL PARAMETER CONDITIONS MIN. MAX. UNIT VCC supply voltage −0.5 +4.6 V IIK input diode current V I<0 −− 50 mA VI input voltage −0.5 +4.6 V IOK output diode current V O >V CC or VO <0 −± 50 mA VO output voltage enable mode; notes 1 and 2 −0.5 V CC + 0.5 V disable mode −0.5 +4.6 V Power-down mode; note 2 −0.5 +4.6 V IO output source or sink current VO = 0 to VCC −± 50 mA ICC , IGND VCC or GND current −± 100 mA Tstg storage temperature −65 +150 °C Ptot power dissipation SO package above 70 °C derate linearly with 8 mW/K − 500 mW TSSOP package above 60 °C derate linearly with 5.5 mW/K − 500 mW

2002 Nov 18 6

Philips Semiconductors Product specification Quad buffer/line driver; 3-state 74ALVC125 DC CHARACTERISTICS At recommended operating conditions; voltages are referenced to GND (ground=0V ) . Notes 1. All typical values are measured at Tamb =2 5°C. 2. For transceivers, the parameter IOZ includes the input leakage current. SYMBOL PARAMETER TEST CONDITIONS MIN. TYP. (1) MAX. UNIT OTHER V CC (V) Tamb = −40 to +85°C VIH HIGH-level input voltage 1.65 to 1.95 0.65× VCC −− V 2.7 to 3.6 2 −− V VIL LOW-level input voltage 1.65 to 1.95−− 0.35× VCC V VOL LOW-level output voltage VI=V IH or VIL IO = 100µA 1.65 to 3.6 −− 0.2 V IO = 6 mA 1.65 − 0.11 0.3 V IO =1 2m A 2 . 3 − 0.17 0.4 V IO =1 8m A 2 . 3 − 0.25 0.6 V IO =1 2m A 2 . 7 − 0.16 0.4 V IO =1 8m A 3 . 0 − 0.23 0.4 V IO =2 4m A 3 . 0 − 0.30 0.55 V VOH HIGH-level output voltage VI=V IH or VIL IO = −100 µA 1.65 to 3.6 V CC − 0.2 −− V IO = −6 mA 1.65 1.25 1.51 − V IO = −12 mA 2.3 1.8 2.10 − V IO = −18 mA 2.3 1.7 2.01 − V IO = −12 mA 2.7 2.2 2.53 − V IO = −18 mA 3.0 2.4 2.76 − V IO = −24 mA 3.0 2.2 2.68 − V ILI input leakage current VI= 3.6 V or GND 3.6 −± 0.1 ±5 µA IOZ 3-state output OFF-state current VI=V IH or VIL; VO = 3.6 V or GND; note 2 3.6 − 0.1 ±10 µA Ioff power OFF leakage current VIor VO = 3.6 V 0.0 −± 0.1 ±10 µA ICC quiescent supply current VI=V CC or GND; IO = 0 3.6 − 0.2 10 µA ΔICC additional quiescent supply current per input pin V I=V CC − 0.6 V; IO = 0 3.0 to 3.6 − 5 750 µA

2002 Nov 18 7

Philips Semiconductors Product specification Quad buffer/line driver; 3-state 74ALVC125 AC CHARACTERISTICS Note 1. All typical values are measured at Tamb =2 5°C. AC WAVEFORMS SYMBOL PARAMETER TEST CONDITIONS MIN. TYP. (1) MAX. UNIT WAVEFORMS V CC (V) Tamb = −40 to +85°C tPHL /tPLH propagation delay input nA to output nY 2.7 − 2.0 3.1 ns t PZH /tPZL 3-state output enable time input nOE to output nY 2.7 − 2.7 4.3 ns tPHZ /tPLZ 3-state output disable time input nOE to output nY 2.7 − 2.9 4.0 ns MNA230 tPHL tPLH VM VMnA input nY output GND VI VOH VOL Fig.5 Input nA to output nY propagation delay times. VCC VM INPUT VI tr =tf 1.65 to 1.95 V 0.5× VCC VCC ≤ 2.0 ns 2.3 to 2.7 V 0.5 × VCC VCC ≤ 2.0 ns 2.7 V 1.5 V 2.7 V ≤ 2.5 ns

2002 Nov 18 8

Philips Semiconductors Product specification Quad buffer/line driver; 3-state 74ALVC125 handbook, full pagewidth MNA654 tPLZ tPHZ outputs disabled outputs enabled Vy Vx outputs enabled output LOW-to-OFF OFF-to-LOW output HIGH-to-OFF OFF-to-HIGH nOE input VI VCC VM VOL VOH GND GND tPZL tPZH VM VM Fig.6 3-state enable and disable times. VCC VM INPUT VI tr =tf 1.65 to 1.95 V 0.5× VCC VCC ≤ 2.0 ns 2.3 to 2.7 V 0.5 × VCC VCC ≤ 2.0 ns 2.7 V 1.5 V 2.7 V ≤ 2.5 ns VX =V OL + 0.3 V at VCC ≥ 2.7 V; VX =V OL + 0.15 V at VCC < 2.7 V; VY =V OH − 0.3 V at VCC ≥ 2.7 V; VY =V OH − 0.15 V at VCC < 2.7 V.

2002 Nov 18 9

Philips Semiconductors Product specification Quad buffer/line driver; 3-state 74ALVC125 handbook, full pagewidth VEXT VCC VI VO MNA616 D.U.T. C LR T R L R L PULSE GENERATOR Fig.7 Load circuitry for switching times. Definitions for test circuit R L = Load resistor. C L = Load capacitance including jig and probe capacitance. R T = Termination resistance should be equal to the output impedance Zo of the pulse generator. VCC VI C L R L VEXT tPLH /tPHL tPZH /tPHZ tPZL /tPLZ 1.65 to 1.95 V VCC 30 pF 1 k Ω open GND 2 × VCC 2.3 to 2.7 V V CC 30 pF 500 Ω open GND 2 × VCC 2.7 V 2.7 V 50 pF 500 Ω open GND 6 V 3.0 to 3.6 V 2.7 V 50 pF 500 Ω open GND 6 V

2002 Nov 18 10

Philips Semiconductors Product specification Quad buffer/line driver; 3-state 74ALVC125 PACKAGE OUTLINES UNIT A max. A 1 A 2 A 3 bp cD (1) E (1) (1)eH E LL p QZ ywv θ REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC EIAJ mm inches 1.75 0.25 0.10 1.45 1.25 0.25 0.49 0.36 0.25 0.19 8.75 8.55 4.0 3.8 1.27 6.2 5.8 0.7 0.6 0.7 0.3 8 o o 0.25 0.1 DIMENSIONS (inch dimensions are derived from the original mm dimensions) Note 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 1.0 0.4 SOT108-1 X w M θ AA 1 A 2 bp D H E Lp Q detail X E Z e c L v M A (A )3 A y 076E06 MS-012 pin 1 index 0.069 0.010 0.004 0.057 0.049 0.01 0.019 0.014 0.0100 0.0075 0.35 0.34 0.16 0.15 0.050 1.05 0.0410.244 0.228 0.028 0.024 0.028 0.0120.01 0.25 0.01 0.0040.039 0.016 97-05-22 99-12-27 0 2.5 5 mm scale SO14: plastic small outline package; 14 leads; body width 3.9 mm SOT108-1

2002 Nov 18 11

Philips Semiconductors Product specification Quad buffer/line driver; 3-state 74ALVC125 UNIT A 1 A 2 A 3 bp cD (1) E (2) (1)eH E LL p QZ ywv θ REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC EIAJ mm 0.15 0.05 0.95 0.80 0.30 0.19 0.2 0.1 5.1 4.9 4.5 4.3 0.65 6.6 6.2 0.4 0.3 0.72 0.38 o o0.13 0.10.21.0 DIMENSIONS (mm are the original dimensions) Notes 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. Plastic interlead protrusions of 0.25 mm maximum per side are not included. 0.75 0.50 SOT402-1 MO-153 95-04-04 99-12-27 w M bp D Z e 0.25 14 8 θ AA 1 A 2 Lp Q detail X L (A )3 H E E c v M A XA y 0 2.5 5 mm scale TSSOP14: plastic thin shrink small outline package; 14 leads; body width 4.4 mm SOT402-1 A max. 1.10 pin 1 index

2002 Nov 18 12

Philips Semiconductors Product specification Quad buffer/line driver; 3-state 74ALVC125 SOLDERING Introduction to soldering surface mount packages This text gives a very brief insight to a complex technology. A more in-depth account of soldering ICs can be found in our “Data Handbook IC26; Integrated Circuit Packages” (document order number 9398 652 90011). There is no soldering method that is ideal for all surface mount IC packages. Wave soldering can still be used for certain surface mount ICs, but it is not suitable for fine pitch SMDs. In these situations reflow soldering is recommended. Reflow soldering Reflow soldering requires solder paste (a suspension of fine solder particles, flux and binding agent) to be applied to the printed-circuit board by screen printing, stencilling or pressure-syringe dispensing before package placement. Several methods exist for reflowing; for example, convection or convection/infrared heating in a conveyor type oven. Throughput times (preheating, soldering and cooling) vary between 100 and 200 seconds depending on heating method. Typical reflow peak temperatures range from 215 to 250°C. The top-surface temperature of the packages should preferable be kept below 220°C for thick/large packages, and below 235°C for small/thin packages. Wave soldering Conventional single wave soldering is not recommended for surface mount devices (SMDs) or printed-circuit boards with a high component density, as solder bridging and non-wetting can present major problems. To overcome these problems the double-wave soldering method was specifically developed. If wave soldering is used the following conditions must be observed for optimal results:

  • Use a double-wave soldering method comprising a turbulent wave with high upward pressure followed by a smooth laminar wave.
  • For packages with leads on two sides and a pitch (e): – larger than or equal to 1.27 mm, the footprint longitudinal axis ispreferred to be parallel to the transport direction of the printed-circuit board; – smaller than 1.27 mm, the footprint longitudinal axis must be parallel to the transport direction of the printed-circuit board. The footprint must incorporate solder thieves at the downstream end.
  • For packages with leads on four sides, the footprint must be placed at a 45° angle to the transport direction of the printed-circuit board. The footprint must incorporate solder thieves downstream and at the side corners. During placement and before soldering, the package must be fixed with a droplet of adhesive. The adhesive can be applied by screen printing, pin transfer or syringe dispensing. The package can be soldered after the adhesive is cured. Typical dwell time is 4 seconds at 250°C. A mildly-activated flux will eliminate the need for removal of corrosive residues in most applications. Manual soldering Fix the component by first soldering two diagonally-opposite end leads. Use a low voltage (24 V or less) soldering iron applied to the flat part of the lead. Contact time must be limited to 10 seconds at up to 300 °C. When using a dedicated tool, all other leads can be soldered in one operation within 2 to 5 seconds between 270 and 320°C.

2002 Nov 18 13

Philips Semiconductors Product specification Quad buffer/line driver; 3-state 74ALVC125 Suitability of surface mount IC packages for wave and reflow soldering methods Notes 1. For more detailed information on the BGA packages refer to the“(LF)BGA Application Note” (AN01026); order a copy from your Philips Semiconductors sales office. 2. All surface mount (SMD) packages are moisture sensitive. Depending upon the moisture content, the maximum temperature (with respect to time) and body size of the package, there is a risk that internal or external package cracks may occur due to vaporization of the moisture in them (the so called popcorn effect). For details, refer to the Drypack information in the “Data Handbook IC26; Integrated Circuit Packages; Section: Packing Methods”. 3. These packages are not suitable for wave soldering. On versions with the heatsink on the bottom side, the solder cannot penetrate between the printed-circuit board and the heatsink. On versions with the heatsink on the top side, the solder might be deposited on the heatsink surface. 4. If wave soldering is considered, then the package must be placed at a 45° angle to the solder wave direction. The package footprint must incorporate solder thieves downstream and at the side corners. 5. Wave soldering is suitable for LQFP, TQFP and QFP packages with a pitch (e) larger than 0.8 mm; it is definitely not suitable for packages with a pitch (e) equal to or smaller than 0.65 mm. 6. Wave soldering is suitable for SSOP and TSSOP packages with a pitch (e) equal to or larger than 0.65 mm; it is definitely not suitable for packages with a pitch (e) equal to or smaller than 0.5 mm. PACKAGE (1) SOLDERING METHOD WAVE REFLOW (2) BGA, LBGA, LFBGA, SQFP , TFBGA, VFBGA not suitable suitable DHVQFN, HBCC, HBGA, HLQFP , HSQFP , HSOP , HTQFP , HTSSOP , HVQFN, HVSON, SMS not suitable(3) suitable PLCC (4), SO, SOJ suitable suitable LQFP , QFP , TQFP not recommended (4)(5) suitable SSOP , TSSOP , VSO not recommended (6) suitable

2002 Nov 18 14

Philips Semiconductors Product specification Quad buffer/line driver; 3-state 74ALVC125 DATA SHEET STATUS Notes 1. Please consult the most recently issued data sheet before initiating or completing a design. 2. The product status of the device(s) described in this data sheet may have changed since this data sheet was 3. For data sheets describing multiple type numbers, the highest-level product status determines the data sheet status. LEVEL DATA SHEET STATUS (1) PRODUCT STATUS (2)(3) DEFINITION I Objective data Development This data sheet contains data from the objective specification for product development. Philips Semiconductors reserves the right to change the specification in any manner without notice. II Preliminary data Qualification This data sheet contains data from the preliminary specification. Supplementary data will be published at a later date. Philips Semiconductors reserves the right to change the specification without notice, in order to improve the design and supply the best possible product. III Product data Production This data sheet contains data from the product specification. Philips Semiconductors reserves the right to make changes at any time in order to improve the design, manufacturing and supply. Relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN). DEFINITIONS Short-form specification The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 60134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. DISCLAIMERS Life support applications These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes Philips Semiconductors reserves the right to make changes in the products - including circuits, standard cells, and/or software - described or contained herein in order to improve design and/or performance. When the product is in full production (status ‘Production’), relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN). Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no licence or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified.

2002 Nov 18 15

Philips Semiconductors Product specification Quad buffer/line driver; 3-state 74ALVC125 NOTES

© Koninklijke Philips Electronics N.V. 2002 SCA74 All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights. Philips Semiconductors – a worldwide company Contact information For additional information please visit http://www.semiconductors.philips.com. Fax: +31 40 27 24825 Printed in The Netherlands 613508/01/pp16 Date of release:2002 Nov 18 Document order number: 9397 750 10451