74AHC2G126 PHILIPS
Document overview
- Manufacturer or author: Provided By digicamel.com
- PDF pages: 20
Technical content
- General description The 74AHC2G126; AHCT2G126 is a high-speed Si-gate CMOS device. The 74AHC2G126; AHCT2G126 provides a dual non-inverting buffer/line driver with 3-state output. The 3-state output is controlled by the output enable input (OE). A LOW at pin nOE causes the output to assume a high-impedance OFF-state. 2. Features ■ Symmetrical output impedance ■ High noise immunity ■ ESD protection: ◆ HBM EIA/JESD22-A114-B exceeds 2000 V ◆ MM EIA/JESD22-A115-A exceeds 200 V ◆ CDM EIA/JESD22-C101 exceeds 1000 V. ■ Low power dissipation ■ Balanced propagation delays ■ Multiple package options ■ Specified from−40 °C to +85°C and from−40 °C to +125°C. 3. Quick reference data 74AHC2G126; 74AHCT2G126 Dual buffer/line driver; 3-state Rev. 02 — 21 September 2004 Product data sheet Table 1: Quick reference data GND = 0 V; Tamb = 25°C; tr = tf≤ 3.0 ns. Symbol Parameter Conditions Min Typ Max Unit Type 74AHC2G126 t PHL , tPLH propagation delay nA to nY C L = 15 pF; VCC = 5 V - 3.4 5.5 ns C I input capacitance - 1.5 10 pF C PD power dissipation capacitance C L = 50 pF; fi = 1 MHz [1][2] -1 0 -p F
9397 750 13736 © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 02 — 21 September 2004 2 of 20 Philips Semiconductors 74AHC2G126; 74AHCT2G126 Dual buffer/line driver; 3-state [1] C PD is used to determine the dynamic power dissipation (PD inµW). PD = CPD × VCC 2 × fi× N +Σ(CL × VCC 2 × fo) where: fi = input frequency in MHz; fo = output frequency in MHz; C L = output load capacitance in pF; VCC = supply voltage in Volts; N = total load switching outputs; Σ(C L × VCC 2 × fo) = sum of the outputs. [2] The condition is VI = GND to VCC . 4. Ordering information Type 74AHCT2G126 tPHL , tPLH propagation delay nA to nY C L = 15 pF; VCC = 5 V - 3.4 5.5 ns C I input capacitance - 1.5 10 pF C PD power dissipation capacitance C L = 50 pF; fi = 1 MHz [1][2] -1 0 -p F Table 1: Quick reference data …continued GND = 0 V; Tamb = 25°C; tr = tf≤ 3.0 ns. Symbol Parameter Conditions Min Typ Max Unit Table 2: Ordering information Type number Package Temperature range Name Description Version 74AHC2G126DP −40 °C to +125°C TSSOP8 plastic thin shrink small outline package; 8 leads; body width 3 mm; lead length 0.5 mm SOT505-2 74AHCT2G126DP −40 °C to +125°C TSSOP8 plastic thin shrink small outline package; 8 leads; body width 3 mm; lead length 0.5 mm SOT505-2 74AHC2G126DC −40 °C to +125°C VSSOP8 plastic very thin shrink small outline package; 8 leads; body width 2.3 mm SOT765-1 74AHCT2G126DC −40 °C to +125°C VSSOP8 plastic very thin shrink small outline package; 8 leads; body width 2.3 mm SOT765-1 74AHC2G126GM −40 °C to +125°C XSON8 plastic extremely thin small outline package; no leads; 8 terminals; body 0.95× 1.95× 0.5 mm SOT833-1 74AHCT2G126GM −40 °C to +125°C XSON8 plastic extremely thin small outline package; no leads; 8 terminals; body 0.95× 1.95× 0.5 mm SOT833-1
9397 750 13736 © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 02 — 21 September 2004 3 of 20 Philips Semiconductors 74AHC2G126; 74AHCT2G126 Dual buffer/line driver; 3-state 5. Marking 6. Functional diagram Table 3: Marking Type number Marking code 74AHC2G126DP A26 74AHCT2G126DP C26 74AHC2G126DC A26 74AHCT2G126DC C26 74AHC2G126GM A26 74AHCT2G126GM C26 Fig 1. Logic symbol. Fig 2. IEC logic symbol. Fig 3. Logic diagram. mna946 2OE 1OE mna947
1 EN1
9397 750 13736 © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 02 — 21 September 2004 4 of 20 Philips Semiconductors 74AHC2G126; 74AHCT2G126 Dual buffer/line driver; 3-state 7. Pinning information
7.1 Pinning
7.2 Pin description
Fig 4. Pin configuration TSSOP8 and VSSOP8. Fig 5. Pin configuration XSON8. 126 1OE V CC 1A 2OE 2Y 1Y GND 2A 001aab648 126 2OE V CC 1OE GND 001aab647 Transparent top view Table 4: Pin description Symbol Pin Description 1OE 1 output enable input (active HIGH) 1A 2 data input 2Y 3 data output GND 4 ground (0 V) 2A 5 data input 1Y 6 data output 2OE 7 output enable input (active HIGH) V CC 8 supply voltage
9397 750 13736 © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 02 — 21 September 2004 5 of 20 Philips Semiconductors 74AHC2G126; 74AHCT2G126 Dual buffer/line driver; 3-state 8. Functional description
8.1 Function table
[1] H = HIGH voltage level; L = LOW voltage level; X = don’t care; Z = high-impedance OFF-state. 9. Limiting values [1] The input and output voltage ratings may be exceeded if the input and output current ratings are observed. 10. Recommended operating conditions Table 5: Function table[1] Input Output nOE nA nY HL L HHH LXZ Table 6: Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V). Symbol Parameter Conditions Min Max Unit VCC supply voltage −0.5 +7.0 V VI input voltage −0.5 +7.0 V IIK input diode current VI <−0.5 V - −20 mA IOK output diode current VO < −0.5 V or VO >V CC + 0.5 V [1] - ±20 mA IO output source or sink current VO > −0.5 V or VO < VCC + 0.5 V - ±25 mA ICC , IGND VCC or GND current - ±75 mA Tstg storage temperature −65 +150 °C Ptot power dissipation Tamb =−40 °C to +125°C - 250 mW Table 7: Recommended operating conditions Symbol Parameter Conditions Min Typ Max Unit Type 74AHC2G126 V CC supply voltage 2.0 5.0 5.5 V VI input voltage 0 - 5.5 V VO output voltage 0 - V CC V Tamb operating ambient temperature see Section11 and Section12 per device −40 +25 +125 °C tr, tf input rise and fall times VCC = 3.3 V± 0.3 V - - 100 ns/V VCC = 5.0 V± 0.5 V - - 20 ns/V
9397 750 13736 © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 02 — 21 September 2004 6 of 20 Philips Semiconductors 74AHC2G126; 74AHCT2G126 Dual buffer/line driver; 3-state 11. Static characteristics Type 74AHCT2G126 VCC supply voltage 4.5 5.0 5.5 V VI input voltage 0 - 5.5 V VO output voltage 0 - V CC V Tamb operating ambient temperature see Section11 and Section12 per device −40 +25 +125 °C tr, tf input rise and fall times VCC = 5.0 V± 0.5 V - - 20 ns/V Table 7: Recommended operating conditions …continued Symbol Parameter Conditions Min Typ Max Unit Table 8: Static characteristics type 74AHC2G126 At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Symbol Parameter Conditions Min Typ Max Unit Tamb = 25°C VIH HIGH-level input voltage VCC = 2.0 V 1.5 - - V VCC = 3.0 V 2.1 - - V VCC = 5.5 V 3.85 - - V VIL LOW-level input voltage VCC = 2.0 V - - 0.5 V VCC = 3.0 V - - 0.9 V VCC = 5.5 V - - 1.65 V VOH HIGH-level output voltage VI = VIH or VIL IO =−50 µA; VCC = 2.0 V 1.9 2.0 - V IO =−50 µA; VCC = 3.0 V 2.9 3.0 - V IO =−50 µA; VCC = 4.5 V 4.4 4.5 - V IO =−4.0 mA; VCC = 3.0 V 2.58 - - V IO =−8.0 mA; VCC = 4.5 V 3.94 - - V VOL LOW-level output voltage VI = VIH or VIL IO = 50µA; VCC = 2.0 V - 0 0.1 V IO = 50µA; VCC = 3.0 V - 0 0.1 V IO = 50µA; VCC = 4.5 V - 0 0.1 V IO = 4.0 mA; VCC = 3.0 V - - 0.36 V IO = 8.0 mA; VCC = 4.5 V - - 0.36 V IOZ 3-state OFF-state current VI = VCC or GND; VCC = 5.5 V - - 0.25 µA ILI input leakage current VI = VCC or GND; VCC = 5.5 V - - 0.1 µA ICC quiescent supply current VI = VCC or GND; IO = 0 A; VCC = 5.5 V - - 1.0 µA C I input capacitance - 1.5 10 pF
9397 750 13736 © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 02 — 21 September 2004 7 of 20 Philips Semiconductors 74AHC2G126; 74AHCT2G126 Dual buffer/line driver; 3-state Tamb =−40 °C to +85°C VIH HIGH-level input voltage VCC = 2.0 V 1.5 - - V VCC = 3.0 V 2.1 - - V VCC = 5.5 V 3.85 - - V VIL LOW-level input voltage VCC = 2.0 V - - 0.5 V VCC = 3.0 V - - 0.9 V VCC = 5.5 V - - 1.65 V VOH HIGH-level output voltage VI = VIH or VIL IO =−50 µA; VCC = 2.0 V 1.9 - - V IO =−50 µA; VCC = 3.0 V 2.9 - - V IO =−50 µA; VCC = 4.5 V 4.4 - - V IO =−4.0 mA; VCC = 3.0 V 2.48 - - V IO =−8.0 mA; VCC = 4.5 V 3.8 - - V VOL LOW-level output voltage VI = VIH or VIL IO = 50µA; VCC = 2.0 V - - 0.1 V IO = 50µA; VCC = 3.0 V - - 0.1 V IO = 50µA; VCC = 4.5 V - - 0.1 V IO = 4.0 mA; VCC = 3.0 V - - 0.44 V IO = 8.0 mA; VCC = 4.5 V - - 0.44 V IOZ 3-state OFF-state current VI = VCC or GND; VCC = 5.5 V - - 2.5 µA ILI input leakage current VI = VCC or GND; VCC = 5.5 V - - 1.0 µA ICC quiescent supply current VI = VCC or GND; IO = 0 A; VCC = 5.5 V --1 0 µA C I input capacitance - - 10 pF Tamb =−40 °C to +125°C VIH HIGH-level input voltage VCC = 2.0 V 1.5 - - V VCC = 3.0 V 2.1 - - V VCC = 5.5 V 3.85 - - V VIL LOW-level input voltage VCC = 2.0 V - - 0.5 V VCC = 3.0 V - - 0.9 V VCC = 5.5 V - - 1.65 V VOH HIGH-level output voltage VI = VIH or VIL IO =−50 µA; VCC = 2.0 V 1.9 - - V IO =−50 µA; VCC = 3.0 V 2.9 - - V IO =−50 µA; VCC = 4.5 V 4.4 - - V IO =−4.0 mA; VCC = 3.0 V 2.40 - - V IO =−8.0 mA; VCC = 4.5 V 3.70 - - V Table 8: Static characteristics type 74AHC2G126 …continued At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Symbol Parameter Conditions Min Typ Max Unit
9397 750 13736 © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 02 — 21 September 2004 8 of 20 Philips Semiconductors 74AHC2G126; 74AHCT2G126 Dual buffer/line driver; 3-state VOL LOW-level output voltage VI = VIH or VIL IO = 50µA; VCC = 2.0 V - - 0.1 V IO = 50µA; VCC = 3.0 V - - 0.1 V IO = 50µA; VCC = 4.5 V - - 0.1 V IO = 4.0 mA; VCC = 3.0 V - - 0.55 V IO = 8.0 mA; VCC = 4.5 V - - 0.55 V IOZ 3-state OFF-state current VI = VCC or GND; VCC = 5.5 V - - 10 µA ILI input leakage current VI = VCC or GND; VCC = 5.5 V - - 2.0 µA ICC quiescent supply current VI = VCC or GND; IO = 0 A; VCC = 5.5 V --4 0 µA C I input capacitance - - 10 pF Table 8: Static characteristics type 74AHC2G126 …continued At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Symbol Parameter Conditions Min Typ Max Unit Table 9: Static characteristics type 74AHCT2G126 At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Symbol Parameter Conditions Min Typ Max Unit Tamb = 25°C VIH HIGH-level input voltage VCC = 4.5 V to 5.5 V 2.0 - - V VIL LOW-level input voltage VCC = 4.5 V to 5.5 V - - 0.8 V VOH HIGH-level output voltage VI = VIH or VIL IO =−50 µA; VCC = 4.5 V 4.4 4.5 4.5 V IO =−8.0 mA; VCC = 4.5 V 3.94 - - V VOL LOW-level output voltage VI = VIH or VIL IO = 50µA; VCC = 4.5 V - 0 0.1 V IO = 8.0 mA; VCC = 4.5 V - - 0.36 V IOZ 3-state OFF-state current VI = VCC or GND; VCC = 5.5 V - - 0.25 µA ILI input leakage current VI = VIH or VIL; VCC = 5.5 V - - 0.1 µA ICC quiescent supply current VI = VCC or GND; IO = 0 A; VCC = 5.5 V - - 1.0 µA ΔICC additional quiescent supply current per input pin V I = 3.4 V; other inputs at VCC or GND; IO = 0 A; VCC = 5.5 V - - 1.35 mA C I input capacitance - 1.5 10 pF Tamb =−40 °C to +85°C VIH HIGH-level input voltage VCC = 4.5 V to 5.5 V 2.0 - - V VIL LOW-level input voltage VCC = 4.5 V to 5.5 V - - 0.8 V
9397 750 13736 © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 02 — 21 September 2004 9 of 20 Philips Semiconductors 74AHC2G126; 74AHCT2G126 Dual buffer/line driver; 3-state VOH HIGH-level output voltage VI = VIH or VIL IO =−50 µA; VCC = 4.5 V 4.4 - - V IO =−8.0 mA; VCC = 4.5 V 3.8 - - V VOL LOW-level output voltage VI = VIH or VIL IO = 50µA; VCC = 4.5 V - - 0.1 V IO = 8.0 mA; VCC = 4.5 V - - 0.44 V IOZ 3-state OFF-state current VI = VCC or GND; VCC = 5.5 V - - 2.5 µA ILI input leakage current VI = VIH or VIL; VCC = 5.5 V - - 1.0 µA ICC quiescent supply current VI = VCC or GND; IO = 0 A; VCC = 5.5V --1 0 µA ΔICC additional quiescent supply current per input pin V I = 3.4 V; other inputs at VCC or GND; IO = 0 A; VCC = 5.5 V - - 1.5 mA C I input capacitance - - 10 pF Tamb =−40 °C to +125°C VIH HIGH-level input voltage VCC = 4.5 V to 5.5 V 2.0 - - V VIL LOW-level input voltage VCC = 4.5 V to 5.5 V - - 0.8 V VOH HIGH-level output voltage VI = VIH or VIL IO =−50 µA; VCC = 4.5 V 4.4 - - V IO =−8.0 mA; VCC = 4.5 V 3.70 - - V VOL LOW-level output voltage VI = VIH or VIL IO = 50µA; VCC = 4.5 V - - 0.1 V IO = 8.0 mA; VCC = 4.5 V - - 0.55 V IOZ 3-state OFF-state current VI = VCC or GND; VCC = 5.5 V - - 10 µA ILI input leakage current VI = VIH or VIL; VCC = 5.5 V - - 2.0 µA ICC quiescent supply current VI = VCC or GND; IO = 0 A; VCC = 5.5 V --4 0 µA ΔICC additional quiescent supply current per input pin V I = 3.4 V; other inputs at VCC or GND; IO = 0 A; VCC = 5.5 V - - 1.5 mA C I input capacitance - - 10 pF Table 9: Static characteristics type 74AHCT2G126 …continued At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Symbol Parameter Conditions Min Typ Max Unit
9397 750 13736 © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 02 — 21 September 2004 10 of 20 Philips Semiconductors 74AHC2G126; 74AHCT2G126 Dual buffer/line driver; 3-state 12. Dynamic characteristics Table 10: Dynamic characteristics type 74AHC2G126 GND = 0 V; tr = tf≤ 3.0 ns; seeFigure8. Symbol Parameter Test conditions Min Typ Max Unit Tamb = 25°C tPHL , tPLH propagation delay nA to nY see Figure6 VCC = 3.0 V to 3.6 V; CL =1 5p F [1] - 4.7 8.0 ns VCC = 4.5 V to 5.5 V; CL =1 5p F [2] - 3.4 5.5 ns VCC = 3.0 V to 3.6 V; CL =5 0p F [1] - 6.6 11.5 ns VCC = 4.5 V to 5.5 V; CL =5 0p F [2] - 4.8 7.5 ns tPZH , tPZL propagation delay nOE to nY see Figure7 VCC = 3.0 V to 3.6 V; CL =1 5p F [1] - 5.0 8.0 ns VCC = 4.5 V to 5.5 V; CL =1 5p F [2] - 3.6 5.1 ns VCC = 3.0 V to 3.6 V; CL =5 0p F [1] - 6.9 11.5 ns VCC = 4.5 V to 5.5 V; CL =5 0p F [2] - 4.9 7.5 ns tPHZ , tPLZ propagation delay nOE to nY see Figure7; CL =1 5p F VCC = 3.0 V to 3.6 V; CL =1 5p F [1] - 6.0 9.7 ns VCC = 4.5 V to 5.5 V; CL =1 5p F [2] - 4.1 6.8 ns VCC = 3.0 V to 3.6 V; CL =5 0p F [1] - 8.3 13.2 ns VCC = 4.5 V to 5.5 V; CL =5 0p F [2] - 5.7 8.8 ns C PD power dissipation capacitance C L = 50 pF; fi = 1 MHz [3][4] -1 0 -p F Tamb =−40 °C to +85°C tPHL , tPLH propagation delay nA to nY see Figure6 VCC = 3.0 V to 3.6 V; CL = 15 pF 1.0 - 9.5 ns VCC = 4.5 V to 5.5 V; CL = 15 pF 1.0 - 6.5 ns VCC = 3.0 V to 3.6 V; CL = 50 pF 1.0 - 13.0 ns VCC = 4.5 V to 5.5 V; CL = 50 pF 1.0 - 8.5 ns tPZH , tPZL propagation delay nOE to nY see Figure7 VCC = 3.0 V to 3.6 V; CL = 15 pF 1.0 - 9.5 ns VCC = 4.5 V to 5.5 V; CL = 15 pF 1.0 - 6.0 ns VCC = 3.0 V to 3.6 V; CL = 50 pF 1.0 - 13.0 ns VCC = 4.5 V to 5.5 V; CL = 50 pF 1.0 - 9.0 ns tPHZ , tPLZ propagation delay nOE to nY see Figure7; CL =1 5p F VCC = 3.0 V to 3.6 V; CL = 15 pF 1.0 - 11.5 ns VCC = 4.5 V to 5.5 V; CL = 15 pF 1.0 - 8.0 ns VCC = 3.0 V to 3.6 V; CL = 50 pF 1.0 - 15.0 ns VCC = 4.5 V to 5.5 V; CL = 50 pF 1.0 - 10.0 ns
9397 750 13736 © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 02 — 21 September 2004 11 of 20 Philips Semiconductors 74AHC2G126; 74AHCT2G126 Dual buffer/line driver; 3-state [1] Typical values are measured at VCC = 3.3 V. [2] Typical values are measured at VCC = 5.0 V. [3] C PD is used to determine the dynamic power dissipation (PD inµW). PD = CPD × VCC 2 × fi× N +Σ(CL × VCC 2 × fo) where: fi = input frequency in MHz; fo = output frequency in MHz; C L = output load capacitance in pF; VCC = supply voltage in Volts; N = total load switching outputs; Σ(C L × VCC 2 × fo) = sum of the outputs. [4] The condition is VI = GND to VCC . Tamb =−40 °C to +125°C tPHL , tPLH propagation delay nA to nY see Figure6 VCC = 3.0 V to 3.6 V; CL = 15 pF 1.0 - 11.5 ns VCC = 4.5 V to 5.5 V; CL = 15 pF 1.0 - 7.0 ns VCC = 3.0 V to 3.6 V; CL = 50 pF 1.0 - 14.5 ns VCC = 4.5 V to 5.5 V; CL = 50 pF 1.0 - 9.5 ns tPZH , tPZL propagation delay nOE to nY see Figure7 VCC = 3.0 V to 3.6 V; CL = 15 pF 1.0 - 11.5 ns VCC = 4.5 V to 5.5 V; CL = 15 pF 1.0 - 6.5 ns VCC = 3.0 V to 3.6 V; CL = 50 pF 1.0 - 14.5 ns VCC = 4.5 V to 5.5 V; CL = 50 pF 1.0 - 9.5 ns tPHZ , tPLZ propagation delay nOE to nY see Figure7; CL =1 5p F VCC = 3.0 V to 3.6 V; CL = 15 pF 1.0 - 12.5 ns VCC = 4.5 V to 5.5 V; CL = 15 pF 1.0 - 8.5 ns VCC = 3.0 V to 3.6 V; CL = 50 pF 1.0 - 16.5 ns VCC = 4.5 V to 5.5 V; CL = 50 pF 1.0 - 11.0 ns Table 10: Dynamic characteristics type 74AHC2G126 …continued GND = 0 V; tr = tf≤ 3.0 ns; seeFigure8. Symbol Parameter Test conditions Min Typ Max Unit Table 11: Dynamic characteristics type 74AHCT2G126 GND = 0 V; tr = tf≤ 3.0 ns; VCC = 4.5 V to 5.5 V; seeFigure8 Symbol Parameter Test conditions Min Typ Max Unit Tamb = 25°C [1] tPHL , tPLH propagation delay nA to nY see Figure6 C L = 15 pF - 3.4 5.5 ns C L = 50 pF - 4.8 7.5 ns tPZH , tPZL propagation delay nOE to nY see Figure7 C L = 15 pF - 3.9 5.1 ns C L = 50 pF - 5.1 7.5 ns tPHZ , tPLZ propagation delay nOE to nY see Figure7 C L = 15 pF - 4.5 6.8 ns C L = 50 pF - 6.1 8.8 ns
9397 750 13736 © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 02 — 21 September 2004 12 of 20 Philips Semiconductors 74AHC2G126; 74AHCT2G126 Dual buffer/line driver; 3-state [1] Typical values are measured at VCC = 5.0 V. [2] C PD is used to determine the dynamic power dissipation (PD inµW). PD = CPD × VCC 2 × fi× N +Σ(CL × VCC 2 × fo) where: fi = input frequency in MHz; fo = output frequency in MHz; C L = output load capacitance in pF; VCC = supply voltage in Volts; N = total load switching outputs; Σ(C L × VCC 2 × fo) = sum of the outputs. [3] The condition is VI = GND to VCC . C PD power dissipation capacitance C L = 50 pF; fi = 1 MHz [2][3] -1 0 -p F Tamb =−40 °C to +85°C tPHL , tPLH propagation delay nA to nY see Figure6 C L = 15 pF 1.0 - 6.5 ns C L = 50 pF 1.0 - 8.5 ns tPZH , tPZL propagation delay nOE to nY see Figure7 C L = 15 pF 1.0 - 6.0 ns C L = 50 pF 1.0 - 9.0 ns tPHZ , tPLZ propagation delay nOE to nY see Figure7 C L = 15 pF 1.0 - 8.0 ns C L = 50 pF 1.0 - 10.0 ns Tamb =−40 °C to +125°C tPHL , tPLH propagation delay nA to nY see Figure6 C L = 15 pF 1.0 - 7.0 ns C L = 50 pF 1.0 - 9.5 ns tPZH , tPZL propagation delay nOE to nY see Figure7 C L = 15 pF 1.0 - 6.5 ns C L = 50 pF 1.0 - 9.5 ns tPHZ , tPLZ propagation delay nOE to nY see Figure7 C L = 15 pF 1.0 - 8.5 ns C L = 50 pF 1.0 - 11.0 ns Table 11: Dynamic characteristics type 74AHCT2G126 …continued GND = 0 V; tr = tf≤ 3.0 ns; VCC = 4.5 V to 5.5 V; seeFigure8 Symbol Parameter Test conditions Min Typ Max Unit
9397 750 13736 © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 02 — 21 September 2004 13 of 20 Philips Semiconductors 74AHC2G126; 74AHCT2G126 Dual buffer/line driver; 3-state 13. Waveforms Measurement points are given inTable12. Fig 6. The input (nA) to output (nY) propagation delays. Table 12: Measurement points Type Input Output VI VM VM VX VY 74AHC2G126 GND to V CC 5 0%V CC 5 0%V CC VOL + 0.3 V V OL − 0.3 V 74AHCT2G126 GND to 3.0 V 1.5 V 50 % V CC VOL + 0.3 V V OL − 0.3 V Measurement points are given inTable12. Fig 7. The 3-state enable and disable times. mna230 tPHL tPLH VM VMnA input nY output GND VI VOH VOL mna949 tPLZ tPHZ outputs disabled outputs enabled VY VX outputs enabled output LOW-to-OFF OFF-to-LOW output HIGH-to-OFF OFF-to-HIGH nOE input VOL VOH VCC VI VM GND GND tPZL tPZH VM VM
9397 750 13736 © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 02 — 21 September 2004 14 of 20 Philips Semiconductors 74AHC2G126; 74AHCT2G126 Dual buffer/line driver; 3-state Switch positions: tPLH , tPHL : open tPLZ , tPZL : VCC tPHZ , tPZH : GND Definitions for test circuit: C L = Load capacitance including jig and probe capacitance (seeSection12 for the value). R L = Load resistor. R T = Termination resistance should be equal to the output impedance Zo of the pulse generator. Fig 8. Load circuitry for switching times. open GND VCC VCC VI VO mna232 D.U.T. C LR T R L = 1000 Ω PULSE GENERATOR
9397 750 13736 © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 02 — 21 September 2004 15 of 20 Philips Semiconductors 74AHC2G126; 74AHCT2G126 Dual buffer/line driver; 3-state 14. Package outline Fig 9. Package outline SOT505-2 (TSSOP8). UNIT A 1 A max. A 2 A 3 bp LH E Lp wyvce D (1) E(1) Z(1) q REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA mm 0.15 0.00 0.95 0.75 0.38 0.22 0.18 0.08 3.1 2.9 3.1 2.9 0.65 4.1 3.9 0.70 0.35 0°0.13 0.10.20.5 DIMENSIONS (mm are the original dimensions) Note 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 0.47 0.33 w Mbp D Z e 0.25 8 5 q Lp (A3) detail X A L H E E c v M A XA y 2.5 5 mm0 scale TSSOP8: plastic thin shrink small outline package; 8 leads; body width 3 mm; lead length 0.5 mmSOT505-2 1.1 pin 1 index
9397 750 13736 © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 02 — 21 September 2004 16 of 20 Philips Semiconductors 74AHC2G126; 74AHCT2G126 Dual buffer/line driver; 3-state Fig 10. Package outline SOT765-1 (VSSOP8). UNIT A 1 A max. A 2 A 3 bp LH E Lp wyvce D (1) E(2) Z(1) θ REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA mm 0.15 0.00 0.85 0.60 0.27 0.17 0.23 0.08 2.1 1.9 2.4 2.2 0.5 3.2 3.0 0.4 0.1 0°0.13 0.10.20.4 DIMENSIONS (mm are the original dimensions) Notes 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. Plastic or metal protrusions of 0.25 mm maximum per side are not included. 0.40 0.15 Q 0.21 0.19 SOT765-1 MO-187 02-06-07 w Mbp D Z e 0.12 8 5 θ Q Lp (A3) detail X A L H E E c v M A X A y 2.5 5 mm0 scale VSSOP8: plastic very thin shrink small outline package; 8 leads; body width 2.3 mm SOT765-1 pin 1 index
9397 750 13736 © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 02 — 21 September 2004 17 of 20 Philips Semiconductors 74AHC2G126; 74AHCT2G126 Dual buffer/line driver; 3-state Fig 11. Package outline SOT833-1 (XSON8). terminal 1 index area REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA SOT833-1 04-07-15 04-07-22 DIMENSIONS (mm are the original dimensions) XSON8: plastic extremely thin small outline package; no leads; 8 terminals; body 0.95 x 1.95 x 0.5 mm D E e A 1 b LL1 e1 e1 0 1 2 mm scale Notes 1. Including plating thickness. 2. Can be visible in some manufacturing processes. UNIT mm 0.25 0.17 2.0 1.9 0.35 0.27 A max b E 1.0 0.9 D ee 1 L 0.40 0.32 0.50.6 A (1) max 0.5 0.04 (2) (2) A
9397 750 13736 © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 02 — 21 September 2004 18 of 20 Philips Semiconductors 74AHC2G126; 74AHCT2G126 Dual buffer/line driver; 3-state 15. Revision history Table 13: Revision history Document ID Release date Data sheet statusChange notice Order number Supersedes 74AHC_AHCT2G126_2 20040921 Product data sheet - 9397 750 13736 74AHC_AHCT2G126_1 Modification: • Addition of SOT833-1 and Ordering information. 74AHC_AHCT2G126_1 20040304 Product data sheet - 9397 750 12698 -
Philips Semiconductors 74AHC2G126; 74AHCT2G126 Dual buffer/line driver; 3-state 9397 750 13736 © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 02 — 21 September 2004 19 of 20 16. Data sheet status [1] Please consult the most recently issued data sheet before initiating or completing a design. [2] The product status of the device(s) described in this data sheet may have changed since this data sheet was published. The latest information is available on the Internet at URL http://www.semiconductors.philips.com. [3] For data sheets describing multiple type numbers, the highest-level product status determines the data sheet status. 17. Definitions Short-form specification —The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 60134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. 18. Disclaimers Life support —These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes —Philips Semiconductors reserves the right to make changes in the products - including circuits, standard cells, and/or software - described or contained herein in order to improve design and/or performance. When the product is in full production (status ‘Production’), relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN). Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. 19. Contact information For additional information, please visit: http://www.semiconductors.philips.com For sales office addresses, send an email to: sales.addresses@www.semiconductors.philips.com Level Data sheet status[1] Product status[2][3] Definition I Objective data Development This data sheet contains data from the objective specification for product development. Philips Semiconductors reserves the right to change the specification in any manner without notice. II Preliminary data Qualification This data sheet contains data from the preliminary specification. Supplementary data will be published at a later date. Philips Semiconductors reserves the right to change the specification without notice, in order to improve the design and supply the best possible product. III Product data Production This data sheet contains data from the product specification. Philips Semiconductors reserves the right to make changes at any time in order to improve the design, manufacturing and supply. Relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN).
© Koninklijke Philips Electronics N.V. 2004 All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights. Date of release: 21 September 2004 Document number: 9397 750 13736 Published in The Netherlands Philips Semiconductors 74AHC2G126; 74AHCT2G126 Dual buffer/line driver; 3-state 20. Contents