74AHCT595 NEXPERIA
Document overview
- Manufacturer or author: Provided By digicamel.com
- PDF pages: 19
Technical content
Datasheet sections
74AHC595; 74AHCT595 8-bit serial-in/serial-out or parallel-out shift register with output latches Rev. 6 — 26 May 2020 Product data sheet 1. General description The 74AHC595; 74AHCT595 is an 8-bit serial-in/serial or parallel-out shift register with a storage register and 3-state outputs. Both the shift and storage register have separate clocks. The device features a serial input (DS) and a serial output (Q7S) to enable cascading and an asynchronous reset MR input. A LOW on MR will reset the shift register. Data is shifted on the LOW-to-HIGH transitions of the SHCP input. The data in the shift register is transferred to the storage register on a LOW-to-HIGH transition of the STCP input. If both clocks are connected together, the shift register will always be one clock pulse ahead of the storage register. Data in the storage register appears at the output whenever the output enable input (OE) is LOW. A HIGH on OE causes the outputs to assume a high-impedance OFF-state. Operation of the OE input does not affect the state of the registers. The 74AHCT595 features TTL compatible inputs. Both 74AHC595 and 74AHCT595 inputs are overvoltage tolerant. This feature allows the use of these devices as translators in mixed voltage environments. 2. Features and benefits
- Wide supply voltage range from 2.0 V to 5.5 V
- Balanced propagation delays
- All inputs have Schmitt-trigger action
- Overvoltage tolerant inputs to 5.5 V
- High noise immunity
- CMOS low power dissipation
- Input levels:
- The 74AHC595 operates with CMOS input levels
- The 74AHCT595 operates with TTL input levels
- ESD protection:
- HBM JESD22-A114F exceeds 2000 V
- MM JESD22-A115-A exceeds 200 V
- CDM JESD22-C101E exceeds 1000 V
- Latch-up performance exceeds 100 mA per JESD 78 Class II Level A
- Multiple package options
- Specified from -40 °C to +85 °C and from -40 °C to +125 °C 3. Applications
- Serial-to-parallel data conversion
- Remote control holding register
Table 1. Ordering information
13 EN3
Nexperia 74AHC595; 74AHCT595 8-bit serial-in/serial-out or parallel-out shift register with output latches STAGE 0 STAGES 1 TO 6 STAGE 7 FF0 D CP Q R LATCH D CP Q FF7 D CP Q R LATCH D CP Q mna555 D Q Q1 Q2 Q3 Q4 Q5 Q6 Q7 Q7S DS STCP SHCP OE MR Fig. 4. Logic diagram 6. Pinning information 6.1. Pinning 74AHC595 74AHCT595 Q1 VCC Q2 Q0 Q3 DS Q4 OE Q5 STCP Q6 SHCP Q7 MR GND Q7S 001aae538 Fig. 5. Pin configuration SOT109-1 (SO16) and SOT403-1 (TSSOP16) 001aae483 74AHC595 74AHCT595 Q7 MR Q6 SHCP Q5 STCP Q4 OE Q3 DS Q2 Q0 GND Q7S VCC Transparent top view 7 10 6 11 5 12 4 13 3 14 2 15 terminal 1 index area GND(1) (1) This is not a ground pin. There is no electrical or mechanical requirement to solder the pad. In case soldered, the solder land should remain floating or connected to GND. Fig. 6. Pin configuration SOT763-1 (DHVQFN16) 74AHC_AHCT595 All information provided in this document is subject to legal disclaimers. © Nexperia B.V. 2020. All rights reserved Product data sheet Rev. 6 — 26 May 2020 3 / 19
Table 2. Pin description Table 3. Function table Z = high-impedance OFF-state. stage 6 (internal Q6S) appears on the serial output (Q7S).
Table 4. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V). [1] The input and output voltage ratings may be exceeded if the input and output current ratings are observed. [2] For SOT109-1 (SO16) package: Ptot derates linearly with 12.4 mW/K above 110 °C. For SOT403-1 (TSSOP16) package: Ptot derates linearly with 8.5 mW/K above 91 °C. For SOT763-1 (DHVQFN16) package: Ptot derates linearly with 11.2 mW/K above 106 °C.
- Recommended operating conditions
Table 5. Operating conditions Table 6. Static characteristics At recommended operating conditions; voltages are referenced to GND (ground = 0 V).
Table 7. Dynamic characteristics Voltages are referenced to GND (ground = 0 V); for test circuit see Fig. 13.
Nexperia 74AHC595; 74AHCT595 8-bit serial-in/serial-out or parallel-out shift register with output latches 25 °C -40 °C to +85 °C -40 °C to +125 °C Symbol Parameter Conditions Min Typ [1] Max Min Max Min Max Unit MR to Q7S; see Fig. 11 tPHL HIGH to LOW propagation delay OE to Qn; see Fig. 12 [3] ten enable time OE to Qn; see Fig. 12 [4] tdis disable time SHCP or STCP; see Fig. 8 and Fig. 9 VCC = 3.0 V to 3.6 V 80 125 - 60 - 40 - MHz fmax maximum frequency VCC = 4.5 V to 5.5 V 130 170 - 110 - 90 - MHz SHCP HIGH or LOW; see Fig. 8 STCP HIGH or LOW; see Fig. 9 MR LOW; see Fig. 11 tW pulse width DS to SHCP; see Fig. 10 SHCP to STCP; see Fig. 9 tsu set-up time DS to SHCP; see Fig. 10 th hold time MR to SHCP; see Fig. 11 trec recovery time CPD power dissipation capacitance fi = 1 MHz; VI = GND to VCC [5] [6] - 180 - - - - - pF 74AHC_AHCT595 All information provided in this document is subject to legal disclaimers. © Nexperia B.V. 2020. All rights reserved Product data sheet Rev. 6 — 26 May 2020 8 / 19
Nexperia 74AHC595; 74AHCT595 8-bit serial-in/serial-out or parallel-out shift register with output latches 25 °C -40 °C to +85 °C -40 °C to +125 °C Symbol Parameter Conditions Min Typ [1] Max Min Max Min Max Unit 74AHCT595 SHCP to Q7S; see Fig. 8 [2] STCP to Qn; see Fig. 9 [2] tpd propagation delay MR to Q7S; see Fig. 11 tPHL HIGH to LOW propagation OE to Qn; see Fig. 12 [3] ten enable time OE to Qn; see Fig. 12 [4] tdis disable time fmax maximum frequency SHCP and STCP; VCC = 4.5 V to 5.5 V; see Fig. 8 and Fig. 9 130 170 - 110 - 90 - MHz SHCP HIGH or LOW; VCC = 4.5 V to 5.5 V; see Fig. 8 STCP HIGH or LOW; VCC = 4.5 V to 5.5 V; see Fig. 9 tW pulse width MR LOW; VCC = 4.5 V to 5.5 V; see Fig. 11 DS to SHCP; VCC = 4.5 V to 5.5 V; see Fig. 10 3.0 - - 3.0 - 3.0 - nstsu set-up time SHCP to STCP; VCC = 4.5 V to 5.5 V; see Fig. 9 th hold time DS to SHCP; VCC = 4.5 V to 5.5 V; see Fig. 10 trec recovery time MR to SHCP; VCC = 4.5 V to 5.5 V; see Fig. 11 CPD power dissipation capacitance fi = 1 MHz; VI = GND to VCC [5] [6] - 190 - - - - - pF [1] Typical values are measured at nominal supply voltage. [2] tpd is the same as tPHL and tPLH. [3] ten is the same as tPZL and tPZH. [4] tdis is the same as tPLZ and tPHZ. [5] CPD is used to determine the dynamic power dissipation (PD in μW). PD = CPD × VCC 2 × fi + Σ(CL × VCC 2 × fo) where: fi = input frequency in MHz; fo = output frequency in MHz; Σ(CL × VCC 2 × fo) = sum of outputs; CL = output load capacitance in pF; VCC = supply voltage in V. [6] All 9 outputs switching. 74AHC_AHCT595 All information provided in this document is subject to legal disclaimers. © Nexperia B.V. 2020. All rights reserved Product data sheet Rev. 6 — 26 May 2020 9 / 19
Nexperia 74AHC595; 74AHCT595 8-bit serial-in/serial-out or parallel-out shift register with output latches 11.1. Waveforms and test circuit mna557 SHCP input Q7S output tPLH tPHL tW 1/fmax VM VOH VI GND VOL VM Measurement points are given in Table 8. VOL and VOH are typical output voltage levels that occur with the output load. Fig. 8. Shift clock pulse, maximum frequency and input to output propagation delays mna558 STCP input Qn output tPLH tPHL tW tsu 1/fmax VM VOH VI GND VOL VM SHCP input VI GND VM Measurement points are given in Table 8. VOL and VOH are typical output voltage levels that occur with the output load. Fig. 9. Storage clock to output propagation delays 74AHC_AHCT595 All information provided in this document is subject to legal disclaimers. © Nexperia B.V. 2020. All rights reserved Product data sheet Rev. 6 — 26 May 2020 10 / 19
Nexperia 74AHC595; 74AHCT595 8-bit serial-in/serial-out or parallel-out shift register with output latches mna560 GND GND th tsu th tsu VM VM VM VI VOH VOL VI Q7S output SHCP input DS input Measurement points are given in Table 8. The shaded areas indicate when the input is permitted to change for predictable output performance. VOL and VOH are typical output voltage levels that occur with the output load. Fig. 10. Data set-up and hold times mna561 MR input SHCP input Q7S output tPHL tW trec VM VOH VOL VI GND VI GND VM VM Measurement points are given in Table 8. VOL and VOH are typical output voltage levels that occur with the output load. Fig. 11. Master reset to output propagation delays 74AHC_AHCT595 All information provided in this document is subject to legal disclaimers. © Nexperia B.V. 2020. All rights reserved Product data sheet Rev. 6 — 26 May 2020 11 / 19
Measurement points are given in Table 8. VOL and VOH are typical output voltage levels that occur with the output load. Table 8. Measurement points
Test data is given in Table 9. CL = load capacitance including jig and probe capacitance. RT = termination resistance should be equal to the output impedance Zo of the pulse generator. Table 9. Test data
Nexperia 74AHC595; 74AHCT595 8-bit serial-in/serial-out or parallel-out shift register with output latches 12. Package outline X w M θ A A 1 A 2 b p D H E L p Q detail X E Z e c L v M A (A ) 3 A y pin 1 index UNIT A max. A 1 A 2 A 3 b p c D (1) E (1) (1) e H E L L p Q Z y w v θ REFERENCES OUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA mm inches 1.75 0.25 0.10 1.45 1.25 0.25 0.49 0.36 0.25 0.19 10.0 9.8 4.0 3.8 1.27 6.2 5.8 0.7 0.6 0.7 0.3 8 o o 0.25 0.1 DIMENSIONS (inch dimensions are derived from the original mm dimensions) Note 1. Plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included. 1.0 0.4 SOT109-1 99-12-27 03-02-19 076E07 MS-012 0.069 0.010 0.004 0.057 0.049 0.01 0.019 0.014 0.0100 0.0075 0.39 0.38 0.16 0.15 0.05 1.05 0.041 0.244 0.228 0.028 0.020 0.028 0.012 0.01 0.25 0.01 0.004 0.039 0.016 0 2.5 5 mm scale SO16: plastic small outline package; 16 leads; body width 3.9 mm SOT109-1 Fig. 14. Package outline SOT109-1 (SO16) 74AHC_AHCT595 All information provided in this document is subject to legal disclaimers. © Nexperia B.V. 2020. All rights reserved Product data sheet Rev. 6 — 26 May 2020 14 / 19
Nexperia 74AHC595; 74AHCT595 8-bit serial-in/serial-out or parallel-out shift register with output latches UNIT A 1 A 2 A 3 b p c D (1) E (2) (1) e H E L L p Q Z y w v θ REFERENCES OUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA mm 0.15 0.05 0.95 0.80 0.30 0.19 0.2 0.1 5.1 4.9 4.5 4.3 0.65 6.6 6.2 0.4 0.3 0.40 0.06 o o 0.13 0.1 0.2 1 DIMENSIONS (mm are the original dimensions) Notes 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. Plastic interlead protrusions of 0.25 mm maximum per side are not included. 0.75 0.50 SOT403-1 MO-153 99-12-27 03-02-18 w M b p D Z e 0.25 1 8 16 9 θ A A 1 A 2 L p Q detail X L (A ) 3 H E E c v M A X A y 0 2.5 5 mm scale TSSOP16: plastic thin shrink small outline package; 16 leads; body width 4.4 mm SOT403-1 A max. 1.1 pin 1 index Fig. 15. Package outline SOT403-1 (TSSOP16) 74AHC_AHCT595 All information provided in this document is subject to legal disclaimers. © Nexperia B.V. 2020. All rights reserved Product data sheet Rev. 6 — 26 May 2020 15 / 19
Nexperia 74AHC595; 74AHCT595 8-bit serial-in/serial-out or parallel-out shift register with output latches terminal 1 index area 0.5 1 A1 Eh b UNIT y e 0.2 c REFERENCES OUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA mm 3.6 3.4 Dh 2.15 1.85 2.6 2.4 1.15 0.85 2.5 0.30 0.18 0.05 0.00 0.05 0.1 DIMENSIONS (mm are the original dimensions) 0.5 0.3 L 0.1 v 0.05 w 0 2.5 5 mm scale SOT763-1 DHVQFN16: plastic dual in-line compatible thermal enhanced very thin quad flat package; no leads; 16 terminals; body 2.5 x 3.5 x 0.85 mm A(1) max. A c detail X y y1 C e L Eh Dh e b 2 7 15 10 8 1 X D E C B A terminal 1 index area A C C B v M w M E (1) Note 1. Plastic or metal protrusions of 0.075 mm maximum per side are not included. D (1) 02-10-17 03-01-27 Fig. 16. Package outline SOT763-1 (DHVQFN16) 74AHC_AHCT595 All information provided in this document is subject to legal disclaimers. © Nexperia B.V. 2020. All rights reserved Product data sheet Rev. 6 — 26 May 2020 16 / 19
Table 10. Abbreviations Table 11. Revision history
- Legal texts have been adapted to the new company name where appropriate.
- Section 1 and Section 2 updated.
- Fig. 7: Timing diagram updated with SHCP waveform.
- Table 4: Derating values for Ptot total power dissipation updated.
- Table 7: Propagation delay symbol and parameter corrected (Errata). 74AHC_AHCT595 v.5 20120704 Product data sheet - 74AHC_AHCT595 v.4 Modifications: • Added GND in the pin configuration drawing DHVQFN16 (errata) 74AHC_AHCT595 v.4 20090811 Product data sheet - 74AHC_AHCT595 v.3 74AHC_AHCT595 v.3 20080425 Product data sheet - 74AHC_AHCT595 v.2 74AHC_AHCT595 v.2 20060323 Product data sheet - 74AHC_AHCT595 v.1 74AHC_AHCT595 v.1 20000315 Product specification - - 74AHC_AHCT595 All information provided in this document is subject to legal disclaimers. © Nexperia B.V. 2020. All rights reserved Product data sheet Rev. 6 — 26 May 2020 17 / 19
Nexperia 74AHC595; 74AHCT595 8-bit serial-in/serial-out or parallel-out shift register with output latches 15. Legal information Data sheet status Document status [1][2] Product status [3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification. [1] Please consult the most recently issued document before initiating or completing a design. [2] The term 'short data sheet' is explained in section "Definitions". [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the internet at https://www.nexperia.com. Definitions Draft — The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. Nexperia does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet — A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local Nexperia sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. Product specification — The information and data provided in a Product data sheet shall define the specification of the product as agreed between Nexperia and its customer, unless Nexperia and customer have explicitly agreed otherwise in writing. In no event however, shall an agreement be valid in which the Nexperia product is deemed to offer functions and qualities beyond those described in the Product data sheet. Disclaimers Limited warranty and liability — Information in this document is believed to be accurate and reliable. However, Nexperia does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. Nexperia takes no responsibility for the content in this document if provided by an information source outside of Nexperia. In no event shall Nexperia be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Notwithstanding any damages that customer might incur for any reason whatsoever, Nexperia’s aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of Nexperia. Right to make changes — Nexperia reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use — Nexperia products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or malfunction of an Nexperia product can reasonably be expected to result in personal injury, death or severe property or environmental damage. Nexperia and its suppliers accept no liability for inclusion and/or use of Nexperia products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk. Quick reference data — The Quick reference data is an extract of the product data given in the Limiting values and Characteristics sections of this document, and as such is not complete, exhaustive or legally binding. Applications — Applications that are described herein for any of these products are for illustrative purposes only. Nexperia makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Customers are responsible for the design and operation of their applications and products using Nexperia products, and Nexperia accepts no liability for any assistance with applications or customer product design. It is customer’s sole responsibility to determine whether the Nexperia product is suitable and fit for the customer’s applications and products planned, as well as for the planned application and use of customer’s third party customer(s). Customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. Nexperia does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer’s applications or products, or the application or use by customer’s third party customer(s). Customer is responsible for doing all necessary testing for the customer’s applications and products using Nexperia products in order to avoid a default of the applications and the products or of the application or use by customer’s third party customer(s). Nexperia does not accept any liability in this respect. Limiting values — Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the device. Limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the Recommended operating conditions section (if present) or the Characteristics sections of this document is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. Terms and conditions of commercial sale — Nexperia products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nexperia.com/profile/terms, unless otherwise agreed in a valid written individual agreement. In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. Nexperia hereby expressly objects to applying the customer’s general terms and conditions with regard to the purchase of Nexperia products by customer. No offer to sell or license — Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. Export control — This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from competent authorities. Non-automotive qualified products — Unless this data sheet expressly states that this specific Nexperia product is automotive qualified, the product is not suitable for automotive use. It is neither qualified nor tested in accordance with automotive testing or application requirements. Nexperia accepts no liability for inclusion and/or use of non-automotive qualified products in automotive equipment or applications. In the event that customer uses the product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall use the product without Nexperia’s warranty of the product for such automotive applications, use and specifications, and (b) whenever customer uses the product for automotive applications beyond Nexperia’s specifications such use shall be solely at customer’s own risk, and (c) customer fully indemnifies Nexperia for any liability, damages or failed product claims resulting from customer design and use of the product for automotive applications beyond Nexperia’s standard warranty and Nexperia’s product specifications. Translations — A non-English (translated) version of a document is for reference only. The English version shall prevail in case of any discrepancy between the translated and English versions. Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. 74AHC_AHCT595 All information provided in this document is subject to legal disclaimers. © Nexperia B.V. 2020. All rights reserved Product data sheet Rev. 6 — 26 May 2020 18 / 19