74AHC573_10 NXP
Document overview
- Manufacturer or author: Provided By digicamel.com
- PDF pages: 19
Technical content
- General description The 74AHC573; 74AHCT573 is a high-speed Si-gate CMOS device and is pin compatible with Low-power Schottky TTL (LSTTL). It is specified in compliance with JEDEC standard No. 7A. The 74AHC573; 74AHCT573 consists of eight D-type transparent latches featuring separate D-type inputs for each latch and 3-state true outputs for bus oriented applications. A latch enable input (LE) and an output enable input (OE) are common to all latches. When pin LE is HIGH, data at the Dn inputs enters the latches. In this condition the latches are transparent, i.e. a latch output will change state each time its corresponding Dn input changes. When pin LE is LOW, the latches store the information that is present at the Dn inputs, after a set-up time preceding the HIGH-to-LOW transition of LE. When pin OE is LOW, the contents of the 8 latches are available at the outputs. When pin OE is HIGH, the outputs go to the high-impedance OFF-state. Operation of the OE input does not affect the state of the latches. The 74AHC573; 74AHCT573 is functionally identical to the 74AHC373; 74AHCT373, but has a different pin arrangement. 2. Features and benefits Balanced propagation delays All inputs have a Schmitt trigger action Common 3-state output enable input Functionally identical to the 74AHC373; 74AHCT373 Inputs accept voltages higher than VCC Input levels: For 74AHC573: CMOS input level For 74AHCT573: TTL input level ESD protection: HBM EIA/JESD22-A114E exceeds 2000 V MM EIA/JESD22-A115-A exceeds 200 V CDM EIA/JESD22-C101C exceeds 1000 V Multiple package options Specified from −40 °C to +85 °C and from −40 °C to +125 °C 74AHC573; 74AHCT573 Octal D-type transparant latch; 3-state Rev. 05 — 25 March 2010 Product data sheet
Table 1. Ordering information
Product data sheet Rev. 05 — 25 March 2010 3 of 19 NXP Semiconductors 74AHC573; 74AHCT573 Octal D-type transparant latch; 3-state Fig 2. Logic symbol Fig 3. IEC logic symbol mna807 LE OE mna808 11 C1
1 EN1
Fig 4. Logic diagram mna810 D LE Q D LE Q D LE Q D LELELE Q D LATCH LATCH LATCH LATCH LATCH Q LE OE LE LE LE LE D LE Q LATCH LE D LE Q LATCH LE D LE Q LATCH LE
5.1 Pinning
5.2 Pin description
Table 2. Pin description
Z = high-impedance OFF-state. [1] The input and output voltage ratings may be exceeded if the input and output current ratings are observed. [2] For SO20 packages: above 70 °C the value of Ptot derates linearly at 8 mW/K. For TSSOP20 packages: above 60 °C the value of Ptot derates linearly at 5.5 mW/K. For DHVQFN20 packages: above 60 °C the value of Ptot derates linearly with 4.5 mW/K. Table 3. Function table [1] Table 4. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V).
- Recommended operating conditions
Table 5. Operating conditions Table 6. Static characteristics At recommended operating conditions; voltages are referenced to GND (ground = 0 V).
Table 6. Static characteristics …continued At recommended operating conditions; voltages are referenced to GND (ground = 0 V).
Table 7. Dynamic characteristics Voltages are referenced to GND (ground = 0 V); for test circuit see Figure 11.
[1] Typical values are measured at nominal supply voltage (V CC = 3.3 V and VCC = 5.0 V). [2] t pd is the same as tPHL and tPLH. [3] t en is the same as tPZH and tPZL. [4] t dis is the same as tPHZ and tPLZ. [5] C PD is used to determine the dynamic power dissipation (PD in μW). L × VCC2 × fo) = sum of the outputs. Table 7. Dynamic characteristics …continued Voltages are referenced to GND (ground = 0 V); for test circuit see Figure 11.
Product data sheet Rev. 05 — 25 March 2010 10 of 19 NXP Semiconductors 74AHC573; 74AHCT573 Octal D-type transparant latch; 3-state 11. Waveforms Measurement points are given in Table 8. VOL and VOH are typical voltage output levels that occur with the output load. Fig 7. Data input to output propagation delays mna811 Dn input Qn output tPHL tPLH GND VI VM VM VOH VOL VOL and VOH are typical voltage output levels that occur with the output load. Fig 8. Latch enable input to output propagation delays mna812 LE input Qn output tPHL tPLH tW 1/fmax VM VOH VI GND VOL VM
Measurement points are given in Table 8. VOL and VOH are typical voltage output levels that occur with the output load. Measurement points are given in Table 8. VOL and VOH are typical voltage output levels that occur with the output load. The shaded areas indicate when the input is permitted to change for predicable output performance. Table 8. Measurement points
Test data is given in Table 9. RT = termination resistance should be equal to output impedance Zo of the pulse generator. CL = load capacitance including jig and probe capacitance. Table 9. Test data
Product data sheet Rev. 05 — 25 March 2010 13 of 19 NXP Semiconductors 74AHC573; 74AHCT573 Octal D-type transparant latch; 3-state 12. Package outline Fig 12. Package outline SOT163-1 (SO20) UNIT A max. A1 A2 A3 bp cD (1) E (1) (1)eH E LL p Q Zywv θ REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA mm inches 2.65 0.3 0.1 2.45 2.25 0.49 0.36 0.32 0.23 13.0 12.6 7.6 7.4 1.27 10.65 10.00 1.1 1.0 0.9 0.4 8 o o 0.25 0.1 DIMENSIONS (inch dimensions are derived from the original mm dimensions) Note 1. Plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included. 1.1 0.4 SOT163-1 w M bp detail X Z e D y 0.25 075E04 MS-013 pin 1 index 0.1 0.012 0.004 0.096 0.089 0.019 0.014 0.013 0.009 0.51 0.49 0.30 0.29 0.05 1.4 0.0550.419 0.394 0.043 0.039 0.035 0.0160.01 0.25 0.01 0.0040.043 0.0160.01 0 5 10 mm scale X θ AA1 HE Lp Q E c L v M A (A )3 A SO20: plastic small outline package; 20 leads; body width 7.5 mm SOT163-1 99-12-27 03-02-19
Product data sheet Rev. 05 — 25 March 2010 14 of 19 NXP Semiconductors 74AHC573; 74AHCT573 Octal D-type transparant latch; 3-state Fig 13. Package outline SOT360-1 (TSSOP20) UNIT A 1 A2 A3 bp cD (1) E (2) (1)eH E LL p QZ ywv θ REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA mm 0.15 0.05 0.95 0.80 0.30 0.19 0.2 0.1 6.6 6.4 4.5 4.3 0.65 6.6 6.2 0.4 0.3 0.5 0.2 o o0.13 0.10.21 DIMENSIONS (mm are the original dimensions) Notes 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. Plastic interlead protrusions of 0.25 mm maximum per side are not included. 0.75 0.50 SOT360-1 MO-153 99-12-27 03-02-19 w M bp D Z e 0.25 11 0 20 11 pin 1 index θ AA1 Lp Q detail X L (A )3 HE E c v M A XA y 0 2.5 5 mm scale TSSOP20: plastic thin shrink small outline package; 20 leads; body width 4.4 mm SOT360-1 A max. 1.1
Product data sheet Rev. 05 — 25 March 2010 15 of 19 NXP Semiconductors 74AHC573; 74AHCT573 Octal D-type transparant latch; 3-state Fig 14. Package outline SOT764-1 (DHVQFN20) terminal 1 index area 0.51 A1 EhbUNIT ye 0.2 c REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA mm 4.6 4.4 Dh 3.15 2.85 2.6 2.4 1.15 0.85 3.50.30 0.18 0.05 0.00 0.05 0.1 DIMENSIONS (mm are the original dimensions) 0.5 0.3 L 0.1 v 0.05 w 0 2.5 5 mm scale SOT764-1 DHVQFN20: plastic dual in-line compatible thermal enhanced very thin quad flat package; no leads; 20 terminals; body 2.5 x 4.5 x 0.85 mm A(1) max. A c detail X yy1 Ce L Eh Dh e b 19 12 101 X D E C B A terminal 1 index area AC C Bv M w M E(1) Note 1. Plastic or metal protrusions of 0.075 mm maximum per side are not included. D(1) 02-10-17 03-01-27
Table 10. Abbreviations Table 11. Revision history
- Added type numbers 74AHC573BQ and 74AHCT573BQ (DHVQFN20 / SOT764-1 package). 74AHC_AHCT573_3 20080424 Product data sheet - 74AHC_AHCT573_2 74AHC_AHCT573_2 20031208 Product specification - 74AHC_AHCT573_1 74AHC_AHCT573_1 19990927 Pr oduct specification - -
Product data sheet Rev. 05 — 25 March 2010 17 of 19 NXP Semiconductors 74AHC573; 74AHCT573 Octal D-type transparant latch; 3-state 15. Legal information
15.1 Data sheet status
[1] Please consult the most recently issued document before initiating or completing a design. [2] The term ‘short data sheet’ is explained in section “Definitions”. [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com.
15.2 Definitions
Draft — The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet — A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. Product specification — The information and data provided in a Product data sheet shall define the specification of the product as agreed between NXP Semiconductors and its customer, unless NXP Semiconductors and customer have explicitly agreed otherwise in writing. In no event however, shall an agreement be valid in which the NXP Semiconductors product is deemed to offer functions and qualities beyond those described in the Product data sheet.
15.3 Disclaimers
Limited warranty and liability — Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. In no event shall NXP Semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Notwithstanding any damages that customer might incur for any reason whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of NXP Semiconductors. Right to make changes — NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use in automotive applications — This NXP Semiconductors product has been qualified for use in automotive applications. The product is not designed, authorized or warranted to be suitable for use in medical, military, aircraft, space or life support equipment, nor in applications where failure or malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors accepts no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk. Applications — Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. NXP Semiconductors does not accept any liability related to any default, damage, costs or problem which is based on a weakness or default in the customer application/use or the application/use of customer’s third party customer(s) (hereinafter both referred to as “Application”). It is customer’s sole responsibility to check whether the NXP Semiconductors product is suitable and fit for the Application planned. Customer has to do all necessary testing for the Application in order to avoid a default of the Application and the product. NXP Semiconductors does not accept any liability in this respect. Limiting values — Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the device. Limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the Recommended operating conditions section (if present) or the Characteristics sections of this document is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. Terms and conditions of commercial sale — NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms , unless otherwise agreed in a valid written individual agreement. In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. NXP Semiconductors hereby expressly objects to applying the customer’s general terms and conditions with regard to the purchase of NXP Semiconductors products by customer. No offer to sell or license — Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. Export control — This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from national authorities.
15.4 Trademarks
Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This docu ment contains the product specification.
Product data sheet Rev. 05 — 25 March 2010 18 of 19 NXP Semiconductors 74AHC573; 74AHCT573 Octal D-type transparant latch; 3-state 16. Contact information For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com
NXP Semiconductors 74AHC573; 74AHCT573 Octal D-type transparant latch; 3-state © NXP B.V. 2010. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com Date of release: 25 March 2010 Document identifier: 74AHC_AHCT573_5 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section ‘Legal information’. 17. Contents