74AHCT377 NEXPERIA

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 16

Technical content

  1. General description The 74AHC377; 74AHCT377 is a high-speed Si-gate CMOS device and is pin compatible with Low-power Schottky TTL (LSTTL). It is specified in compliance with JEDEC standard No. 7-A. The 74AHC377; 74AHCT377 has eight edge-triggered, D-type flip-flops with individual D inputs and Q outputs. A common clock input (CP) loads all flip-flops simultaneously when the data enable input ( E) is LOW. The state of each D input, one set-up time before the LOW-to-HIGH clock transition, is transferred to the corresponding output (Qn) of the flip-flop. The E input is only required to be stable one set-up time prior to the LOW-to-HIGH transition for predictable operation. For versions associated with the 74AHC377; 74AHCT377, refer to the following:
  • For the master reset version, see 74AHC273; 74AHCT273
  • For the transparent latch version, see 74AHC373; 74AHCT373
  • For the 3-state version, see 74AHC374; 74AHCT374 2. Features n Balanced propagation delays n All inputs have Schmitt-trigger actions n Inputs accept voltages higher than VCC n Ideal for addressable register applications n Data enable for address and data synchronization n Eight positive-edge triggered D-type flip-flops n Input levels: u For 74AHC377: CMOS level u For 74AHCT377: TTL level n ESD protection: u HBM EIA/JESD22-A114E exceeds 2000 V u MM EIA/JESD22-A115-A exceeds 200 V u CDM EIA/JESD22-C101C exceeds 1000 V n Multiple package options n Specified from−40 °C to +85°C and from−40 °C to +125°C 74AHC377; 74AHCT377 Octal D-type flip-flop with data enable; positive-edge trigger Rev. 02 — 12 June 2008 Product data sheet

Table 1. Ordering information

74AHC_AHCT377_2 Product data sheet Rev. 02 — 12 June 2008 3 of 16 Nexperia 74AHC377; 74AHCT377 Octal D-type flip-flop with data enable; positive-edge trigger Fig 2. Logic symbol Fig 3. IEC logic symbol mna918 E CP mna919 11 1C2 1 G1 2D 2 Fig 4. Logic diagram mna610 D FF1 Q CP CP E D FF2 Q CP D FF3 Q CP D FF4 Q CP D FF5 Q CP D FF6 Q CP D FF7 Q CP D FF8 Q CP © Nexperia B.V. 2017. All rights reserved

5.1 Pinning

5.2 Pin description

Table 2. Pin description

[1] The input and output voltage ratings may be exceeded if the input and output current ratings are observed. [2] For SO20 packages: above 70°C the value of Ptot derates linearly at 8 mW/K. For TSSOP20 packages: above 60°C the value of Ptot derates linearly at 5.5 mW/K. Table 3. Function table[1] Table 4. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V).

  1. Recommended operating conditions

Table 5. Operating conditions Table 6. Static characteristics At recommended operating conditions; voltages are referenced to GND (ground = 0 V).

Table 6. Static characteristics …continued At recommended operating conditions; voltages are referenced to GND (ground = 0 V).

Table 7. Dynamic characteristics Voltages are referenced to GND (ground = 0 V); for test circuit seeFigure8.

[1] Typical values are measured at nominal supply voltage (VCC = 3.3 V and VCC = 5.0 V). [2] tpd is the same as tPLH and tPHL . [3] C PD is used to determine the dynamic power dissipation (PD inµW). Σ(CL × VCC 2 × fo) = sum of the outputs. Table 7. Dynamic characteristics …continued Voltages are referenced to GND (ground = 0 V); for test circuit seeFigure8.

Measurement points are given inTable8. VOL and VOH are typical voltage output levels that occur with the output load. Measurement points are given inTable8. The shaded areas indicate when the input is permitted to change for predictable output performance. Table 8. Measurement points

Test data is given inTable9. R T = termination resistance should be equal to output impedance Zo of the pulse generator. C L = load capacitance including jig and probe capacitance. Table 9. Test data

74AHC_AHCT377_2 Product data sheet Rev. 02 — 12 June 2008 12 of 16 Nexperia 74AHC377; 74AHCT377 Octal D-type flip-flop with data enable; positive-edge trigger 12. Package outline Fig 9. Package outline SOT163-1 (SO20) UNIT A max. A 1 A 2 A 3 bp cD (1) E (1) (1)eH E LL p Q Zy w v q REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA mm inches 2.65 0.3 0.1 2.45 2.25 0.49 0.36 0.32 0.23 13.0 12.6 7.6 7.4 1.27 10.65 10.00 1.1 1.0 0.9 0.4 8 o o 0.25 0.1 DIMENSIONS (inch dimensions are derived from the original mm dimensions) Note 1. Plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included. 1.1 0.4 SOT163-1 w M bp detail X Z e D y 0.25 075E04 MS-013 pin 1 index 0.1 0.012 0.004 0.096 0.089 0.019 0.014 0.013 0.009 0.51 0.49 0.30 0.29 0.05 1.4 0.0550.419 0.394 0.043 0.039 0.035 0.0160.01 0.25 0.01 0.0040.043 0.0160.01 0 5 10 mm scale X q AA 1 A 2 H E Lp Q E c L v M A (A )3 A SO20: plastic small outline package; 20 leads; body width 7.5 mm SOT163-1 99-12-27 03-02-19 © Nexperia B.V. 2017. All rights reserved

74AHC_AHCT377_2 Product data sheet Rev. 02 — 12 June 2008 13 of 16 Nexperia 74AHC377; 74AHCT377 Octal D-type flip-flop with data enable; positive-edge trigger Fig 10. Package outline SOT360-1 (TSSOP20) UNIT A 1 A 2 A 3 bp cD (1) E (2) (1)eH E LL p QZ y w v q REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA mm 0.15 0.05 0.95 0.80 0.30 0.19 0.2 0.1 6.6 6.4 4.5 4.3 0.65 6.6 6.2 0.4 0.3 0.5 0.2 o o0.13 0.10.21 DIMENSIONS (mm are the original dimensions) Notes 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. Plastic interlead protrusions of 0.25 mm maximum per side are not included. 0.75 0.50 SOT360-1 MO-153 99-12-27 03-02-19 w M bp D Z e 0.25 11 0 20 11 pin 1 index q AA 1 A 2 Lp Q detail X L (A )3 H E E c v M A XA y 0 2.5 5 mm scale TSSOP20: plastic thin shrink small outline package; 20 leads; body width 4.4 mm SOT360-1 A max. 1.1 © Nexperia B.V. 2017. All rights reserved

Table 10. Abbreviations Table 11. Revision history

  • The format of this data sheet has been redesigned to comply with the new identity guidelines of NXP Semiconductors .
  • Legal texts have been adapted to the new company name where appropriate.
  • Table6: the conditions for input leakage current have been changed. 74AHC_AHCT377_1 20000815 Product specification - - © Nexperia B.V. 2017. All rights reserved

74AHC_AHCT377_2 Product data sheet Rev. 02 — 12 June 2008 15 of 16 Nexperia 74AHC377; 74AHCT377 Octal D-type flip-flop with data enable; positive-edge trigger 15. Legal information

15.1 Data sheet status

[1] Please consult the most recently issued document before initiating or completing a design. [2] The term ‘short data sheet’ is explained in section “Definitions”. [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www .nexperia.com .

15.2 Definitions

Draft —The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. Nexperia does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet —A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local Nexperia sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail.

15.3 Disclaimers

General — Information in this document is believed to be accurate and reliable.However,Nexperiadoesnotgiveanyrepresentationsor warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. Right to make changes —Nexperia reservestherighttomake changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use — Nexperia products are not designed, authorized or warranted to be suitable for use in medical, military, aircraft, space or life support equipment, nor in applications where failure or malfunction of a Nexperia product can reasonably be expected to result in personal injury, death or severe property or environmental damage. Nexperia accepts no liability for inclusion and/or use of Nexperia products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk. Applications —Applications that are described herein for any of these products are for illustrative purposes only. Nexperia makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Limiting values —Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) may cause permanent damage to the device. Limiting values are stress ratings only and operation of the device at these or any other conditions above those given in the Characteristics sections of this document is not implied. Exposure to limiting values for extended periods may affect device reliability. Terms and conditions of sale — Nexperia products are sold subject to the general terms and conditions of commercial sale, as published athttp://www.nexperia.com /profi le/ter ms , including those pertaining to warranty, intellectual property rights infringement and limitation of liability, unless explicitly otherwise agreed to in writing by Nexperia. In case of any inconsistency or conflict between information in this document and such terms and conditions, the latter will prevail. No offer to sell or license —Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights.

15.4 Trademarks

Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. 16. Contact information For more information, please visit:http://www .nexperia.com For sales office addresses, please send an email to:salesaddresses@nexperia.com Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification. © Nexperia B.V. 2017. All rights reserved

Nexperia 74AHC377; 74AHCT377 Octal D-type flip-flop with data enable; positive-edge trigger 17. Contents © Nexperia B.V. 2017. All rights reserved For more information, please visit: http://www.nexperia.com For sales office addresses, please send an email to: salesaddresses@nexperia.com Date of release:

12 June 2008