74AHC1G66 PHILIPS
Document overview
- Manufacturer or author: Provided By digicamel.com
- PDF pages: 24
Technical content
Product specification Supersedes data of 2002 Feb 15
2002 Jun 06
74AHC1G66; 74AHCT1G66 Bilateral switch
2002 Jun 06 2
Philips Semiconductors Product specification Bilateral switch 74AHC1G66; 74AHCT1G66
FEATURES
- Very low ON-resistance: –2 6 Ω (typical) at VCC = 3.0 V –1 6 Ω (typical) at VCC = 4.5 V –1 4 Ω (typical) at VCC = 5.5 V.
- ESD protection: – HBM EIA/JESD22-A114-A exceeds 2000 V – MM EIA/JESD22-A115-A exceeds 200 V – CDM EIA/JESD22-C101 exceeds 1000 V.
- High noise immunity
- Low power dissipation
- Balanced propagation delays
- SOT353 and SOT753 package
- Output capability: non standard
- Specified from−40 to +125°C.
DESCRIPTION
The 74AHC1G/AHCT1G66 is a high-speed Si-gate CMOS device. The 74AHC1G/AHCT1G66 provides an analog switch. The switch has two input/output pins (Y and Z) and an active HIGH enable input pin (E). When pin E is LOW, the analog switch is turned off. QUICK REFERENCE DATA Ground = 0 V; T amb =2 5°C; tr =tf≤ 3n s . Notes 1. C PD is used to determine the dynamic power dissipation (PD inµW). PD =C PD × VCC 2 × fi+ ((CL +C S)× VCC 2 × fo) where: fi= input frequency in MHz; fo = output frequency in MHz; C L = output load capacitance in pF; C S = maximum switch capacitance in pF; VCC = supply voltage in Volts. 2. The condition is VI= GND to VCC . SYMBOL PARAMETER CONDITIONS TYPICAL UNIT AHC1G AHCT1G tPZH /tPZL turn-on time E to Vos C L = 15 pF; RL =1k Ω ; VCC =5V 33n s tPHZ /tPLZ turn-off time E to Vos C L = 15 pF; RL =1k Ω ; VCC =5V 55n s C I input capacitance 2 2 pF C PD power dissipation capacitance CL = 50 pF; f = 10 MHz; notes 1 and 2 13 15 pF C S switch capacitance 4 4 pF
2002 Jun 06 3
Philips Semiconductors Product specification Bilateral switch 74AHC1G66; 74AHCT1G66 FUNCTION TABLE See note 1. Note 1. H = HIGH voltage level; L = LOW voltage level.
ORDERING INFORMATION
RANGE PINS PACKAGE MATERIAL CODE MARKING 74AHC1G66GW −40 to +125°C 5 SC-88A plastic SOT353 AL 74AHCT1G66GW −40 to +125°C 5 SC-88A plastic SOT353 CL 74AHC1G66GV −40 to +125°C 5 SC-74A plastic SOT753 A66 74AHCT1G66GV −40 to +125°C 5 SC-74A plastic SOT753 C66 PIN SYMBOL DESCRIPTION
1 Y independent input/output
2 Z independent output/input
3 GND ground (0 V)
4 E enable input (active HIGH)
handbook, halfpage MNA074 VCC Z EGND Y Fig.1 Pin configuration. handbook, halfpage MNA627 Y Z E Fig.2 Logic symbol.
2002 Jun 06 4
Philips Semiconductors Product specification Bilateral switch 74AHC1G66; 74AHCT1G66 handbook, halfpage MNA076 4 # 1 2 Fig.3 IEC logic symbol. handbook, halfpage MNA628VCC E Y Z Fig.4 Logic diagram.
2002 Jun 06 5
Philips Semiconductors Product specification Bilateral switch 74AHC1G66; 74AHCT1G66 RECOMMENDED OPERATING CONDITIONS LIMITING VALUES In accordance with the Absolute Maximum Rating System (IEC 60134); voltages are referenced to GND (ground = 0 V); note 1. Note 1. To avoid drawing VCC current out of pin Z, when switch current flows into pin Y, the voltage drop across the bidirectional switch must not exceed 0.4 V. If the switch current flows into pin Z, no VCC current will flow out of pin Y. In this case there is no limit for the voltage drop across the switch, but the voltage at pins Y and Z may not exceed V CC or GND. SYMBOL PARAMETER CONDITIONS 74AHC1G66 74AHCT1G66 UNIT VI input voltage 0 − 5.5 0 − 5.5 V VS switch voltage 0 − VCC 0 − VCC V Tamb operating ambient temperature see DC and AC characteristics per device −40 +25 +125 −40 +25 +125 °C t r,tf input rise and fall times VCC = 3.3±0.3 V −− 100 −−− ns/V SYMBOL PARAMETER CONDITIONS MIN. MAX. UNIT VCC supply voltage −0.5 +7.0 V IIK input diode current V I< −0.5 V or VI>V CC + 0.5 V −− 20 mA ISK switch diode current V S < −0.5 V or VS >V CC + 0.5 V −± 20 mA IS switch source or sink current−0 . 5V<VO <V CC + 0.5 V −± 25 mA ICC , IGND VCC or GND current −± 75 mA Tstg storage temperature −65 +150 °C PD power dissipation per package for temperature range from−40 to +125°C − 250 mW
2002 Jun 06 6
Philips Semiconductors Product specification Bilateral switch 74AHC1G66; 74AHCT1G66 DC CHARACTERISTICS Type 74AHC1G66 At recommended operating conditions; voltages are referenced to GND (ground = 0 V). SYMBOL PARAMETER TEST CONDITIONS T amb (°C) UNIT OTHER VCC (V) 25 −40 to +85 −40 to +125 VIH HIGH-level input voltage VIL LOW-level input voltage ILI input leakage current VI=V CC or GND 5.5 −− 0.1 − 1.0 − 2.0 µA IS analog switch current, OFF-state VI=V IH or VIL; |VS|=V CC − GND; see Fig.5 analog switch current, ON-state VI=V IH or VIL; |VS|=V CC − GND; see Fig.6 ICC quiescent supply current VI=V CC or GND; Vis= GND or VCC ; Vos =V CC or GND C I input capacitance of enable input (E) − 21 0 − 10 − 10 pF C S maximum switch capacitance independent I/O − 41 0 − 10 − 10 pF
2002 Jun 06 7
Philips Semiconductors Product specification Bilateral switch 74AHC1G66; 74AHCT1G66 Type 74AHCT1G66 At recommended operating conditions; voltages are referenced to GND (ground=0V ) . SYMBOL PARAMETER TEST CONDITIONS T amb (°C) UNIT OTHER V CC (V) 25 −40 to +85 −40 to +125 VIH HIGH-level input voltage VIL LOW-level input voltage ILI input leakage current VI=V CC or GND 5.5 −− 0.1 − 1.0 − 2.0 µA IS analog switch current, OFF-state V I=V IH or VIL; |VS|=V CC − GND; see Fig.5 analog switch current, ON-state V I=V IH or VIL; |VS|=V CC − GND; see Fig.6 ICC quiescent supply current VI=V CC or GND; Vis= GND or VCC ; Vos =V CC or GND ΔICC additional quiescent supply current V I= 3.4 V; other inputs at V CC or GND; IO =0 C I input capacitance of enable input (E) − 21 0 − 10 − 10 pF C S maximum switch capacitance independent I/O − 41 0 − 10 − 10 pF
2002 Jun 06 8
Philips Semiconductors Product specification Bilateral switch 74AHC1G66; 74AHCT1G66 Type 74AHC1G66 and 74AHCT1G66 Note 1. At supply voltage approaching 2 V, the analog switch ON-resistance becomes extremely non-linear. Therefore, it is recommended that these devices are used to transmit digital signals only, when using this supply voltage. SYMBOL PARAMETER TEST CONDITIONS Tamb (°C) UNIT25 −40 to +85 −40 to +125 VCC = 2.0 V; IS = 1 mA; VI=V IH or VIL;see Figs 7 and 8 R ON ON-resistance (peak) Vis=V CC to GND − 148(1) −−−−−Ω ON-resistance (rail) VCC = 3.0 to 3.6 V; IS = 10 mA; VI=V IH or VIL;see Figs 7 and 8 R ON ON-resistance (peak) Vis=V CC to GND − 28 50 − 70 − 110 Ω ON-resistance (rail) Vis= GND − 20 50 − 65 − 90 Ω Vis=V CC − 18 50 − 65 − 90 Ω VCC = 4.5 to 5.5 V; IS = 10 mA; VI=V IH or VIL;see Figs 7 and 8 R ON ON-resistance (peak) Vis=V CC to GND − 15 30 − 40 − 60 Ω ON-resistance (rail) Vis= GND − 15 22 − 26 − 40 Ω Vis=V CC − 13 22 − 26 − 40 Ω
2002 Jun 06 9
Philips Semiconductors Product specification Bilateral switch 74AHC1G66; 74AHCT1G66 handbook, full pagewidth MNA079 AA YZ VI = VCC or GND V O = GND or VCC LOW (from enable input) GND Fig.5 Test circuit for measuring OFF-state current. handbook, full pagewidth MNA080 AA YZ VI = VCC or GND V O (open circuit) HIGH (from enable input) GND Fig.6 Test circuit for measuring ON-state current. handbook, full pagewidth MNA629 V YZ IisVis = 0 to VCC GND HIGH (from enable input) GND Fig.7 Test circuit for measuring ON-resistance (RON ).
2002 Jun 06 10
Philips Semiconductors Product specification Bilateral switch 74AHC1G66; 74AHCT1G66 handbook, halfpage
0246 Vis (V)
(Ω ) MNA630 VCC = 3.0 V 4.5 V 5.5 V Fig.8 Typical ON-resistance as a function of input voltage.
2002 Jun 06 11
Philips Semiconductors Product specification Bilateral switch 74AHC1G66; 74AHCT1G66 AC CHARACTERISTICS Type 74AHC1G66 GND = 0 V; tr =tf≤ 3n s . Note SYMBOL PARAMETER TEST CONDITIONS T amb (°C) UNIT WAVEFORMS C L (pF) 25 −40 to +85 −40 to +125 VCC = 2.0 V; RL =1k Ω ; note 1 tPHL /tPLH propagation delay Visto Vos see Figs 13 and 16 50 − 2.2 5.0 − 6.0 − 7.0 ns tPZH /tPZL turn-on time Et oVos see Figs 14 and 16 15 − 7.0 25.0 − 33.0 − 40.0 ns 50 − 11.0 35.0 − 46.0 − 57.0 ns tPHZ /tPLZ turn-off time Et oVos see Figs 14 and 16 15 − 9.0 25.0 − 33.0 − 40.0 ns 50 − 13.0 35.0 − 46.0 − 57.0 ns VCC = 3.0 to 3.6 V; RL =1k Ω ; note 1 tPHL /tPLH propagation delay Visto Vos see Figs 13 and 16 50 − 1.0 2.0 − 3.0 − 4.0 ns tPZH /tPZL turn-on time Et oVos see Figs 14 and 16 15 − 4.0 11.0 − 14.0 − 18.0 ns 50 − 5.8 15.0 − 20.0 − 25.0 ns tPHZ /tPLZ turn-off time Et oVos see Figs 14 and 16 15 − 6.0 11.0 − 14.0 − 18.0 ns 50 − 8.4 15.0 − 20.0 − 25.0 ns VCC = 4.5 to 5.5 V; RL =1k Ω ; note 1 tPHL /tPLH propagation delay Visto Vos see Figs 13 and 16 50 − 0.6 1.0 − 2.0 − 3.0 ns tPZH /tPZL turn-on time Et oVos see Figs 14 and 16 15 − 3.0 8.0 − 10.0 − 13.0 ns 50 − 4.4 11.0 − 13.0 − 17.0 ns tPHZ /tPLZ turn-off time Et oVos see Figs 14 and 16 15 − 5.0 8.0 − 10.0 − 13.0 ns 50 − 6.1 11.0 − 13.0 − 17.0 ns
2002 Jun 06 12
Philips Semiconductors Product specification Bilateral switch 74AHC1G66; 74AHCT1G66 74AHCT1G66 GND = 0 V; tr =tf≤ 3n s . Note 1. All typical values are measured at VCC =5V . TYPE 74AHC1G66 AND 74AHCT1G66 Recommended conditions and typical values. GND = 0 V; tr =tf=3n s .Visis the input voltage at pins Y or Z, whichever is assigned as an input. Vos is the output voltage at pin Y or Z, whichever is assigned as an output. Notes 1. Adjust input voltage Vis is 0 dBm level (0 dBm=1m W into 600Ω ). 2. Adjust input voltage Vis is 0 dBm level at Vos for 1 MHz (0 dBm=1m W into 50Ω ). SYMBOL PARAMETER TEST CONDITIONS T amb (°C) UNIT WAVEFORMS C L (pF) 25 −40 to +85 −40 to +125 VCC = 4.5 to 5.5 V; RL =1k Ω ; note 1 tPHL /tPLH propagation delay Visto Vos see Figs 13 and 16 50 − 0.7 1.0 − 2.0 − 3.0 ns tPZH /tPZL turn-on time Et oVos see Figs 14 and 16 15 − 3.0 7.0 − 10.0 − 13.0 ns 50 − 4.7 10.0 − 13.0 − 17.0 ns tPHZ /tPLZ turn-off time Et oVos see Figs 14 and 16 15 − 5.0 8.0 − 10.0 − 13.0 ns 50 − 6.5 11.0 − 13.0 − 17.0 ns SYMBOL PARAMETER TEST CONDITIONS V is(p-p)(V) V CC (V) TYPICAL UNIT sine-wave distortion at fin= 1 kHz R L =1 0kΩ ; C L = 50 pF; see Fig.9 2.5 3.0 to 3.6 0.025 % 4.0 4.5 to 5.5 0.015 % sine-wave distortion at fin= 10 kHz R L =1 0kΩ ; C L = 50 pF; see Fig.9 2.5 3.0 to 3.6 0.025 % 4.0 4.5 to 5.5 0.015 % switch OFF signal feed-through R L = 600Ω ; C L = 50 pF; f = 1 MHz; see Fig.10 note 1 3.0 to 3.6 −50 dB 4.5 to 5.5−50 dB fmax minimum frequency response (−3 dB) R L =5 0Ω ; C L = 10 pF; see Figs 11 and 12 note 2 3.0 to 3.6 230 MHz 4.5 to 5.5 280 MHz
2002 Jun 06 13
Philips Semiconductors Product specification Bilateral switch 74AHC1G66; 74AHCT1G66 handbook, full pagewidth MNA632 10 µF R L R L Vos VCC Vis C L DISTORTION METER Z/YY/Z GND fin = 1 kHz sine-wave channel ON Fig.9 Test circuit for measuring sine-wave distortion. handbook, full pagewidth MNA633 0.1 µF R L R L Vos VCC Vis C L dB Z/YY/Z GNDchannel OFF Fig.10 Test circuit for measuring switch OFF signal feed-through.
2002 Jun 06 14
Philips Semiconductors Product specification Bilateral switch 74AHC1G66; 74AHCT1G66 handbook, full pagewidth (dB) MNA643 104 105 106 107 108 109 f (Hz) Fig.11 Typical frequency response. Test conditions: VCC = 4.5 V; GND = 0 V; RL =5 0Ω ; RSOURCE =1k Ω . handbook, full pagewidth MNA631 0.1 µF R L R L Vos VCC Vis C L dB Z/YY/Z GNDchannel ON sine-wave Fig.12 Test circuit for measuring minimum frequency response. Adjust input voltage to obtain 0 dBm at Vos when f = 1 MHz. After set-up, the frequency is increased to obtain a reading of−3d Ba tVos.
2002 Jun 06 15
Philips Semiconductors Product specification Bilateral switch 74AHC1G66; 74AHCT1G66 AC WAVEFORMS handbook, halfpage MNA593 tPLH tPHL VM VMVis Vos GND VI VOH VOL VIINPUT REQUIREMENTS VM INPUT GND to VCC 50% V CC VOL and VOH are typical output voltage drop that occur with the output load. Fig.13 The input (Vis) to output (Vos) propagation delays. handbook, full pagewidth MNA634 tPLZ tPHZ outputs disabled outputs enabled VOH − 0.3 V VOL + 0.3 V outputs enabled output LOW-to-OFF OFF-to-LOW output HIGH-to-OFF OFF-to-HIGH E input VI VCC VM VOL VOH GND GND tPZL tPZH VM VM Fig.14 The turn-on and turn-off times. TYPE VIINPUT REQUIREMENTS VM INPUT V M OUTPUT AHC1G GND to V CC 50% V CC 50% V CC AHCT1G GND to 3.0 V 1.5 V 1.5 V
2002 Jun 06 16
Philips Semiconductors Product specification Bilateral switch 74AHC1G66; 74AHCT1G66 handbook, full pagewidth MNA595 tTHL (tf)t TLH (tr) VM tW positive input pulse negative input pulse 0 V amplitude90% 10% tTLH (tr)t THL (tf) VM tW 0 V amplitude90% 10% Fig.15 Input pulse definitions. FAMILY VIINPUT REQUIREMENTS VM INPUT AHC1G GND to V CC 50% V CC AHCT1G GND to 3.0 V 1.5 V tr =tf= 3 ns, when measuring fmax , there is no constraint on tr,tf with 50% duty factor. handbook, full pagewidth open GND VCC VCC VI VO MNA635 D.U.T. C LR T 1 kΩ PULSE GENERATOR Vis Fig.16 Load circuitry for switching times. Definitions for test circuit: C L = load capacitance including jig and probe capacitance (see “AC characteristics” for values). R T = termination resistance should be equal to the output impedance Zo of the pulse generator. TEST S 1 Vis tPLH /tPHL open pulse tPLZ /tPZL VCC GND tPHZ /tPZH GND V CC
2002 Jun 06 17
Philips Semiconductors Product specification Bilateral switch 74AHC1G66; 74AHCT1G66 PACKAGE OUTLINES REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC EIAJ SOT353 wB Mbp D e A Lp Q detail X H E E v M A AB y 0 1 2 mm scale c X 13 2 Plastic surface mounted package; 5 leads SOT353 UNIT A 1 max bp cD E (2) e1 H E Lp Qy wv mm 0.1 0.30 0.20 2.2 1.8 0.25 0.10 1.35 1.15 0.65 e 1.3 2.2 2.0 0.2 0.10.2 DIMENSIONS (mm are the original dimensions) 0.45 0.15 0.25 0.15 A 1.1 0.8 97-02-28SC-88A
2002 Jun 06 18
Philips Semiconductors Product specification Bilateral switch 74AHC1G66; 74AHCT1G66 REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA SOT753 SC-74A wB Mbp D e A Lp Q detail X H E E v M A AB y 0 1 2 mm scale c X 13 2 Plastic surface mounted package; 5 leads SOT753 UNIT A 1 bp cD E H E Lp Qy wv mm 0.100 0.013 0.40 0.25 3.1 2.7 0.26 0.10 1.7 1.3 e 0.95 3.0 2.5 0.2 0.10.2 DIMENSIONS (mm are the original dimensions) 0.6 0.2 0.33 0.23 A 1.1 0.9 02-04-16
2002 Jun 06 19
Philips Semiconductors Product specification Bilateral switch 74AHC1G66; 74AHCT1G66 SOLDERING Introduction to soldering surface mount packages This text gives a very brief insight to a complex technology. A more in-depth account of soldering ICs can be found in our “Data Handbook IC26; Integrated Circuit Packages” (document order number 9398 652 90011). There is no soldering method that is ideal for all surface mount IC packages. Wave soldering can still be used for certain surface mount ICs, but it is not suitable for fine pitch SMDs. In these situations reflow soldering is recommended. Reflow soldering Reflow soldering requires solder paste (a suspension of fine solder particles, flux and binding agent) to be applied to the printed-circuit board by screen printing, stencilling or pressure-syringe dispensing before package placement. Several methods exist for reflowing; for example, convection or convection/infrared heating in a conveyor type oven. Throughput times (preheating, soldering and cooling) vary between 100 and 200 seconds depending on heating method. Typical reflow peak temperatures range from 215 to 250°C. The top-surface temperature of the packages should preferable be kept below 220°C for thick/large packages, and below 235°C for small/thin packages. Wave soldering Conventional single wave soldering is not recommended for surface mount devices (SMDs) or printed-circuit boards with a high component density, as solder bridging and non-wetting can present major problems. To overcome these problems the double-wave soldering method was specifically developed. If wave soldering is used the following conditions must be observed for optimal results:
- Use a double-wave soldering method comprising a turbulent wave with high upward pressure followed by a smooth laminar wave.
- For packages with leads on two sides and a pitch (e): – larger than or equal to 1.27 mm, the footprint longitudinal axis ispreferred to be parallel to the transport direction of the printed-circuit board; – smaller than 1.27 mm, the footprint longitudinal axis must be parallel to the transport direction of the printed-circuit board. The footprint must incorporate solder thieves at the downstream end.
- For packages with leads on four sides, the footprint must be placed at a 45° angle to the transport direction of the printed-circuit board. The footprint must incorporate solder thieves downstream and at the side corners. During placement and before soldering, the package must be fixed with a droplet of adhesive. The adhesive can be applied by screen printing, pin transfer or syringe dispensing. The package can be soldered after the adhesive is cured. Typical dwell time is 4 seconds at 250°C. A mildly-activated flux will eliminate the need for removal of corrosive residues in most applications. Manual soldering Fix the component by first soldering two diagonally-opposite end leads. Use a low voltage (24 V or less) soldering iron applied to the flat part of the lead. Contact time must be limited to 10 seconds at up to 300 °C. When using a dedicated tool, all other leads can be soldered in one operation within 2 to 5 seconds between 270 and 320°C.
2002 Jun 06 20
Philips Semiconductors Product specification Bilateral switch 74AHC1G66; 74AHCT1G66 Suitability of surface mount IC packages for wave and reflow soldering methods Notes 1. For more detailed information on the BGA packages refer to the“(LF)BGA Application Note” (AN01026); order a copy from your Philips Semiconductors sales office. 2. All surface mount (SMD) packages are moisture sensitive. Depending upon the moisture content, the maximum temperature (with respect to time) and body size of the package, there is a risk that internal or external package cracks may occur due to vaporization of the moisture in them (the so called popcorn effect). For details, refer to the Drypack information in the “Data Handbook IC26; Integrated Circuit Packages; Section: Packing Methods”. 3. These packages are not suitable for wave soldering. On versions with the heatsink on the bottom side, the solder cannot penetrate between the printed-circuit board and the heatsink. On versions with the heatsink on the top side, the solder might be deposited on the heatsink surface. 4. If wave soldering is considered, then the package must be placed at a 45° angle to the solder wave direction. The package footprint must incorporate solder thieves downstream and at the side corners. 5. Wave soldering is suitable for LQFP, TQFP and QFP packages with a pitch (e) larger than 0.8 mm; it is definitely not suitable for packages with a pitch (e) equal to or smaller than 0.65 mm. 6. Wave soldering is suitable for SSOP and TSSOP packages with a pitch (e) equal to or larger than 0.65 mm; it is definitely not suitable for packages with a pitch (e) equal to or smaller than 0.5 mm. PACKAGE (1) SOLDERING METHOD WAVE REFLOW (2) BGA, LBGA, LFBGA, SQFP , TFBGA, VFBGA not suitable suitable HBCC, HBGA, HLQFP , HSQFP , HSOP , HTQFP , HTSSOP , HVQFN, HVSON, SMS not suitable(3) suitable PLCC (4), SO, SOJ suitable suitable LQFP , QFP , TQFP not recommended (4)(5) suitable SSOP , TSSOP , VSO not recommended (6) suitable
2002 Jun 06 21
Philips Semiconductors Product specification Bilateral switch 74AHC1G66; 74AHCT1G66 DATA SHEET STATUS Notes 1. Please consult the most recently issued data sheet before initiating or completing a design. 2. The product status of the device(s) described in this data sheet may have changed since this data sheet was DATA SHEET STATUS (1) PRODUCT STATUS (2) DEFINITIONS Objective data Development This data sheet contains data from the objective specification for product development. Philips Semiconductors reserves the right to change the specification in any manner without notice. Preliminary data Qualification This data sheet contains data from the preliminary specification. Supplementary data will be published at a later date. Philips Semiconductors reserves the right to change the specification without notice, in order to improve the design and supply the best possible product. Product data Production This data sheet contains data from the product specification. Philips Semiconductors reserves the right to make changes at any time in order to improve the design, manufacturing and supply. Changes will be communicated according to the Customer Product/Process Change Notification (CPCN) procedure SNW-SQ-650A. DEFINITIONS Short-form specification The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 60134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. DISCLAIMERS Life support applications These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no licence or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified.
2002 Jun 06 22
Philips Semiconductors Product specification Bilateral switch 74AHC1G66; 74AHCT1G66 NOTES
2002 Jun 06 23
Philips Semiconductors Product specification Bilateral switch 74AHC1G66; 74AHCT1G66 NOTES
© Koninklijke Philips Electronics N.V. 2002 SCA74 All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights. Philips Semiconductors – a worldwide company Contact information For additional information please visit http://www.semiconductors.philips.com. Fax: +31 40 27 24825 Printed in The Netherlands 613508/03/pp24 Date of release:2002 Jun 06 Document order number: 9397 750 09711