74AHC164_08 NXP
Document overview
- Manufacturer or author: Provided By digicamel.com
- PDF pages: 18
Technical content
- General description The 74AHC164; 74AHCT164 shift register is a high-speed Si-gate CMOS device and is pin compatible with Low-power Schottky TTL (LSTTL). It is specified in compliance with JEDEC standard No. 7A. The 74AHC164; 74AHCT164 input signals are 8-bit serial through one of two inputs (DSA or DSB); either input can be used as an active HIGH enable for data entry through the other input. Both inputs must be connected together or an unused input must be tied HIGH. Data shifts one place to the right on each LOW-to-HIGH transition of the clock input (CP) and enters into output Q0, which is a logical AND of the two data inputs (DSA and DSB) that existed one set-up time prior to the rising clock edge. A LOW-level on the master reset ( MR) input overrides all other inputs and clears the register asynchronously, forcing all outputs LOW. 2. Features n Balanced propagation delays n All inputs have Schmitt-trigger actions n Inputs accept voltages higher than VCC n Input levels: u For 74AHC164: CMOS level u For 74AHCT164: TTL level n ESD protection: u HBM EIA/JESD22-A114E exceeds 2000 V u MM EIA/JESD22-A115-A exceeds 200 V u CDM EIA/JESD22-C101C exceeds 1000 V n Multiple package options n Specified from−40 °C to +85°C and from−40 °C to +125°C 74AHC164; 74AHCT164 8-bit serial-in/parallel-out shift register Rev. 03 — 24 April 2008 Product data sheet
74AHC_AHCT164_3 © NXP B.V. 2008. All rights reserved. Table 1. Ordering information
74AHC_AHCT164_3 © NXP B.V. 2008. All rights reserved. Product data sheet Rev. 03 — 24 April 2008 3 of 18 NXP Semiconductors 74AHC164; 74AHCT164 8-bit serial-in/parallel-out shift register Fig 2. Logic symbol Fig 3. IEC logic symbol 001aac423 2 4 CP DSB DSA MR 001aac424 & 31 R C1/ SRG8 Fig 4. Logic diagram 001aac616 D FF1 Q CP R D CP DSB DSA MR D FF2 Q CP R D D FF3 Q CP R D D FF4 Q CP R D D FF5 Q CP R D D FF6 Q CP R D D FF7 Q CP R D D FF8 Q CP R D
74AHC_AHCT164_3 © NXP B.V. 2008. All rights reserved.
5.1 Pinning
5.2 Pin description
Table 2. Pin description
74AHC_AHCT164_3 © NXP B.V. 2008. All rights reserved. q = lower case letter indicates the state of the referenced input one set-up time prior to the LOW-to-HIGH transition. [1] The input and output voltage ratings may be exceeded if the input and output current ratings are observed. [2] For SO14 packages: above 70°C the value of Ptotderates linearly at 8 mW/K. For TSSOP14 packages: above 60°C the value of Ptotderates linearly at 5.5 mW/K. For DHVQFN14 packages: above 60°C the value of Ptotderates linearly at 4.5 mW/K. Table 3. Function table[1] Table 4. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V).
74AHC_AHCT164_3 © NXP B.V. 2008. All rights reserved.
- Recommended operating conditions
Table 5. Operating conditions Table 6. Static characteristics At recommended operating conditions; voltages are referenced to GND (ground = 0 V).
74AHC_AHCT164_3 © NXP B.V. 2008. All rights reserved. Table 6. Static characteristics …continued At recommended operating conditions; voltages are referenced to GND (ground = 0 V).
74AHC_AHCT164_3 © NXP B.V. 2008. All rights reserved. Table 7. Dynamic characteristics Voltages are referenced to GND (ground = 0 V); for test circuit seeFigure10.
74AHC_AHCT164_3 © NXP B.V. 2008. All rights reserved. [1] Typical values are measured at nominal supply voltage (VCC = 3.3 V and VCC = 5.0 V). [2] tpd is the same as tPLH and tPHL . [3] tpd is the same as tPHL only. [4] C PD is used to determine the dynamic power dissipation (PD inµW). L × VCC 2 × fo) = sum of the outputs. Table 7. Dynamic characteristics …continued Voltages are referenced to GND (ground = 0 V); for test circuit seeFigure10.
74AHC_AHCT164_3 © NXP B.V. 2008. All rights reserved. Product data sheet Rev. 03 — 24 April 2008 10 of 18 NXP Semiconductors 74AHC164; 74AHCT164 8-bit serial-in/parallel-out shift register 11. Waveforms Measurement points are given inTable8. VOL and VOH are typical voltage output levels that occur with the output load. Fig 7. Clock pulse width, maximum frequency and input to output propagation delays 001aac426 CP input Qn output tPHL tPLH tW VOH VI GND VOL VM VM 1/fmax Measurement points are given inTable8. VOL and VOH are typical voltage output levels that occur with the output load. Fig 8. Master reset pulse width, recovery time and propagation delays 001aac446 MR input CP input Qn output tPHL tWL trec VM VI GND VI VOH VOL GND VM VM
74AHC_AHCT164_3 © NXP B.V. 2008. All rights reserved. Measurement points are given inTable8. The shaded areas indicate when the input is permitted to change for predictable output performance. OL and VOH are typical voltage output levels that occur with the output load. Table 8. Measurement points
74AHC_AHCT164_3 © NXP B.V. 2008. All rights reserved. Test data is given inTable9. Table 9. Test data
74AHC_AHCT164_3 © NXP B.V. 2008. All rights reserved. Product data sheet Rev. 03 — 24 April 2008 13 of 18 NXP Semiconductors 74AHC164; 74AHCT164 8-bit serial-in/parallel-out shift register 12. Package outline Fig 11. Package outline SOT108-1 (SO14) UNIT A max. A 1 A 2 A 3 bp cD (1) E (1) (1)eH E LL p QZ ywv q REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA mm inches 1.75 0.25 0.10 1.45 1.25 0.25 0.49 0.36 0.25 0.19 8.75 8.55 4.0 3.8 1.27 6.2 5.8 0.7 0.6 0.7 0.3 8 o o 0.25 0.1 DIMENSIONS (inch dimensions are derived from the original mm dimensions) Note 1. Plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included. 1.0 0.4 SOT108-1 X w M q AA 1 A 2 bp D H E Lp Q detail X E Z e c L v M A (A )3 A y 076E06 MS-012 pin 1 index 0.069 0.010 0.004 0.057 0.049 0.01 0.019 0.014 0.0100 0.0075 0.35 0.34 0.16 0.15 0.05 1.05 0.0410.244 0.228 0.028 0.024 0.028 0.0120.01 0.25 0.01 0.0040.039 0.016 99-12-27 03-02-19 0 2.5 5 mm scale SO14: plastic small outline package; 14 leads; body width 3.9 mm SOT108-1
74AHC_AHCT164_3 © NXP B.V. 2008. All rights reserved. Product data sheet Rev. 03 — 24 April 2008 14 of 18 NXP Semiconductors 74AHC164; 74AHCT164 8-bit serial-in/parallel-out shift register Fig 12. Package outline SOT402-1 (TSSOP14) UNIT A 1 A 2 A 3 bp cD (1) E (2) (1)eH E LL p QZ ywv q REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA mm 0.15 0.05 0.95 0.80 0.30 0.19 0.2 0.1 5.1 4.9 4.5 4.3 0.65 6.6 6.2 0.4 0.3 0.72 0.38 o o0.13 0.10.21 DIMENSIONS (mm are the original dimensions) Notes 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. Plastic interlead protrusions of 0.25 mm maximum per side are not included. 0.75 0.50 SOT402-1 MO-153 99-12-27 03-02-18 w M bp D Z e 0.25 14 8 q AA 1 A 2 Lp Q detail X L (A )3 H E E c v M A XA y 0 2.5 5 mm scale TSSOP14: plastic thin shrink small outline package; 14 leads; body width 4.4 mm SOT402-1 A max. 1.1 pin 1 index
74AHC_AHCT164_3 © NXP B.V. 2008. All rights reserved. Product data sheet Rev. 03 — 24 April 2008 15 of 18 NXP Semiconductors 74AHC164; 74AHCT164 8-bit serial-in/parallel-out shift register Fig 13. Package outline SOT762-1 (DHVQFN14) terminal 1 index area 0.51 A 1 EhbUNIT ye 0.2 c REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA mm 3.1 2.9 D h 1.65 1.35 2.6 2.4 1.15 0.85 20.30 0.18 0.05 0.00 0.05 0.1 DIMENSIONS (mm are the original dimensions) 0.5 0.3 L 0.1 v 0.05 w 0 2.5 5 mm scale SOT762-1 DHVQFN14: plastic dual in-line compatible thermal enhanced very thin quad flat package; no leads; 14 terminals; body 2.5 x 3 x 0.85 mm A (1) max. A c detail X yy1 Ce L Eh D h e b 13 9 X D E C B A 02-10-17 03-01-27 terminal 1 index area AC C Bv M w M E (1) Note 1. Plastic or metal protrusions of 0.075 mm maximum per side are not included. D (1)
74AHC_AHCT164_3 © NXP B.V. 2008. All rights reserved. Table 10. Abbreviations Table 11. Revision history
- Table6: the conditions for input leakage current have been changed. 74AHC_AHCT164_2 20061129 Product data sheet - 74AHC_AHCT164_1 74AHC_AHCT164_1 (9397 750 07332)
20000815 Product specification - -
74AHC_AHCT164_3 © NXP B.V. 2008. All rights reserved. Product data sheet Rev. 03 — 24 April 2008 17 of 18 NXP Semiconductors 74AHC164; 74AHCT164 8-bit serial-in/parallel-out shift register 15. Legal information
15.1 Data sheet status
[1] Please consult the most recently issued document before initiating or completing a design. [2] The term ‘short data sheet’ is explained in section “Definitions”. [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com.
15.2 Definitions
Draft —The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet —A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail.
15.3 Disclaimers
General — Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. Right to make changes —NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use —NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in medical, military, aircraft, space or life support equipment, nor in applications where failure or malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors accepts no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk. Applications —Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Limiting values —Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) may cause permanent damage to the device. Limiting values are stress ratings only and operation of the device at these or any other conditions above those given in the Characteristics sections of this document is not implied. Exposure to limiting values for extended periods may affect device reliability. Terms and conditions of sale —NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms , including those pertaining to warranty, intellectual property rights infringement and limitation of liability, unless explicitly otherwise agreed to in writing by NXP Semiconductors. In case of any inconsistency or conflict between information in this document and such terms and conditions, the latter will prevail. No offer to sell or license —Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights.
15.4 Trademarks
Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. 16. Contact information For more information, please visit:http://www.nxp.com For sales office addresses, please send an email to:salesaddresses@nxp.com Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification.
NXP Semiconductors 74AHC164; 74AHCT164 8-bit serial-in/parallel-out shift register © NXP B.V. 2008. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com Date of release: 24 April 2008 Document identifier: 74AHC_AHCT164_3 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section ‘Legal information’. 17. Contents