74ABT821 NXP

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 16

Technical content

  1. General description The 74ABT821 high-performance BiCMOS device combines low static and dynamic power dissipation with high speed and high output drive. The 74ABT821 bus interface register is designed to eliminate the extra packages required to buffer existing registers and provide extra data width for wider data/address paths of buses carrying parity. The 74ABT821 is a buffered 10-bit wide version of the 74ABT374A. The 74ABT821 is a 10-bit, edge-triggered register coupled to ten 3-state output buffers. The device is controlled by the clock (CP) and output enable ( OE) control gates. The register is fully edge triggered. The state of each D input, one set-up time before the LOW-to-HIGH clock transition is transferred to the corresponding output Q of the flip-flop. The 3-state output buffers are designed to drive heavily loaded 3-state buses, MOS memories, or MOS microprocessors. The active LOW output enable (OE) controls all ten 3-state buffers independent of the register operation. WhenOE is LOW, the data in the register appears at the outputs. When OE is HIGH, the outputs are in high-impedance OFF-state, which means they will neither drive nor load the bus. 2. Features and benefits n High-speed parallel registers with positive-edge triggered D-type flip-flops n Ideal where high speed, light loading, or increased fan-in are required with MOS microprocessors n Output capability: +64 mA and−32 mA n Power-on 3-state n Power-on reset n Latch-up protection exceeds 500 mA per JESD78B class II level A n ESD protection: u HBM JESD22-A114F exceeds 2000 V u MM JESD22-A115-A exceeds 200 V 74ABT821 10-bit D-type flip-flop; positive-edge trigger; 3-state Rev. 03 — 25 February 2010 Product data sheet

Table 1. Ordering information

5.1 Pinning

5.2 Pin description

Table 2. Pin description

6.1 Function table

↑ = LOW-to-HIGH clock transition. Table 3. Function table[1]

[1] The input and output voltage ratings may be exceeded if the input and output current ratings are observed. temperatures which are detrimental to reliability. The maximum junction temperature of this integrated circuit should not exceed 150°C.

  1. Recommended operating conditions

Table 4. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Table 5. Recommended operating conditions

[1] For valid test results, data must not be loaded into the flip-flops (or latches) after applying the power. transition time of up to 100µs is permitted. [3] Not more than one output should be tested at a time, and the duration of the test should not exceed one second. [4] This is the increase in supply current for each input at 3.4 V. Table 6. Static characteristics

Table 7. Dynamic characteristics GND = 0 V; for test circuit, seeFigure8. VOL and VOH are typical voltage output levels that occur with the output load.

Product data sheet Rev. 03 — 25 February 2010 8 of 16 NXP Semiconductors 74ABT821 10-bit D-type flip-flop; positive-edge trigger; 3-state VM = 1.5 V. VOL and VOH are typical voltage output levels that occur with the output load. Fig 6. 3-state output (Qn) enable and disable times VM = 1.5 V The shaded areas indicate when the input is permitted to change for predictable output performance. Fig 7. Set-up and hold times data input (Dn) to clock (CP) 001aal299 tPLZ tPHZ outputs disabled outputs enabled VOH − 0.3 V VOL + 0.3 V outputs enabled output LOW-to-OFF OFF-to-LOW output HIGH-to-OFF OFF-to-HIGH OE input VI VOL VOH 3.5 V VM GND GND tPZL tPZH VM VM 001aac738 VM CP input VM VM VM VM VM tsu(H) th(H) tsu(L) th(L) Dn input Vl GND Vl GND

Test data and VEXT levels are given inTable8. C L = Load capacitance including jig and probe capacitance. R T = Termination resistance should be equal to output impedance Zo of the pulse generator. VEXT = Test voltage for switching times. Table 8. Test data

Product data sheet Rev. 03 — 25 February 2010 10 of 16 NXP Semiconductors 74ABT821 10-bit D-type flip-flop; positive-edge trigger; 3-state 12. Package outline Fig 9. Package outline SOT137-1 (SO24) UNIT A max. A 1 A 2 A 3 bp cD (1) E (1) (1)eH E LL p Q Zywv q REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA mm inches 2.65 0.3 0.1 2.45 2.25 0.49 0.36 0.32 0.23 15.6 15.2 7.6 7.4 1.27 10.65 10.00 1.1 1.0 0.9 0.4 8 o o 0.25 0.1 DIMENSIONS (inch dimensions are derived from the original mm dimensions) Note 1. Plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included. 1.1 0.4 SOT137-1 X w M q AA 1 A 2 bp D H E Lp Q detail X E Z c L v M A (A )3 A y 0.25 075E05 MS-013 pin 1 index 0.1 0.012 0.004 0.096 0.089 0.019 0.014 0.013 0.009 0.61 0.60 0.30 0.29 0.05 1.4 0.0550.419 0.394 0.043 0.039 0.035 0.0160.01 0.25 0.01 0.0040.043 0.0160.01 e 0 5 10 mm scale SO24: plastic small outline package; 24 leads; body width 7.5 mm SOT137-1 99-12-27 03-02-19

Product data sheet Rev. 03 — 25 February 2010 11 of 16 NXP Semiconductors 74ABT821 10-bit D-type flip-flop; positive-edge trigger; 3-state Fig 10. Package outline SOT340-1 (SSOP24) UNIT A 1 A 2 A 3 bp cD (1) E (1) (1)eH E LL p QZ ywv q REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA mm 0.21 0.05 1.80 1.65 0.38 0.25 0.20 0.09 8.4 8.0 5.4 5.2 0.65 1.257.9 7.6 0.9 0.7 0.8 0.4 o o0.13 0.10.2 DIMENSIONS (mm are the original dimensions) Note 1. Plastic or metal protrusions of 0.2 mm maximum per side are not included. 1.03 0.63 SOT340-1 MO-150 99-12-27 03-02-19 X w M q A A 1 A 2 bp D H E Lp Q detail X E Z e c L v M A (A )3 A 11 2 24 13 0.25 y pin 1 index 0 2.5 5 mm scale SSOP24: plastic shrink small outline package; 24 leads; body width 5.3 mm SOT340-1 A max.

Product data sheet Rev. 03 — 25 February 2010 12 of 16 NXP Semiconductors 74ABT821 10-bit D-type flip-flop; positive-edge trigger; 3-state Fig 11. Package outline SOT355-1 (TSSOP24) UNIT A 1 A 2 A 3 bp cD (1) E (2) (1)eH E LL p QZ ywv q REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA mm 0.15 0.05 0.95 0.80 0.30 0.19 0.2 0.1 7.9 7.7 4.5 4.3 0.65 6.6 6.2 0.4 0.3 o o0.13 0.10.21 DIMENSIONS (mm are the original dimensions) Notes 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. Plastic interlead protrusions of 0.25 mm maximum per side are not included. 0.75 0.50 SOT355-1 MO-153 99-12-27 03-02-19 0.25 0.5 0.2 w M bp Z e 11 2 24 13 pin 1 index q AA 1 A 2 Lp Q detail X L (A )3 H E E c v M A XAD y 0 2.5 5 mm scale TSSOP24: plastic thin shrink small outline package; 24 leads; body width 4.4 mm SOT355-1 A max. 1.1

Table 9. Abbreviations Table 10. Revision history

  • The format of this data sheet has been redesigned to comply with the new identity guidelines of NXP Semiconductors.
  • Legal texts have been adapted to the new company name where appropriate.
  • DIP 24 (SOT222-1) package removed fromSection 3 “Ordering information” andSection 12 “Package outline”. 74ABT821_2 20050412 Product specification - 74ABT821 74ABT821 19950906 Product specification - -

Product data sheet Rev. 03 — 25 February 2010 14 of 16 NXP Semiconductors 74ABT821 10-bit D-type flip-flop; positive-edge trigger; 3-state 15. Legal information

15.1 Data sheet status

[1] Please consult the most recently issued document before initiating or completing a design. [2] The term ‘short data sheet’ is explained in section “Definitions”. [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com.

15.2 Definitions

Draft —The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet —A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. Product specification —The information and data provided in a Product data sheet shall define the specification of the product as agreed between NXP Semiconductors and its customer, unless NXP Semiconductors and customer have explicitly agreed otherwise in writing. In no event however, shall an agreement be valid in which the NXP Semiconductors product is deemed to offer functions and qualities beyond those described in the Product data sheet.

15.3 Disclaimers

Limited warranty and liability —Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. In no event shall NXP Semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Notwithstanding any damages that customer might incur for any reason whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of NXP Semiconductors. Right to make changes —NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use —NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in medical, military, aircraft, space or life support equipment, nor in applications where failure or malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors accepts no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk. Applications —Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. NXP Semiconductors does not accept any liability related to any default, damage, costs or problem which is based on a weakness or default in the customer application/use or the application/use of customer’s third party customer(s) (hereinafter both referred to as “Application”). It is customer’s sole responsibility to check whether the NXP Semiconductors product is suitable and fit for the Application planned. Customer has to do all necessary testing for the Application in order to avoid a default of the Application and the product. NXP Semiconductors does not accept any liability in this respect. Limiting values —Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the device. Limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the Recommended operating conditions section (if present) or the Characteristics sections of this document is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. Terms and conditions of commercial sale —NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms , unless otherwise agreed in a valid written individual agreement. In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. NXP Semiconductors hereby expressly objects to applying the customer’s general terms and conditions with regard to the purchase of NXP Semiconductors products by customer. No offer to sell or license —Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. Export control —This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from national authorities. Non-automotive qualified products —Unless the data sheet of an NXP Semiconductors product expressly states that the product is automotive qualified, the product is not suitable for automotive use. It is neither qualified nor tested in accordance with automotive testing or application requirements. NXP Semiconductors accepts no liability for inclusion and/or use of non-automotive qualified products in automotive equipment or applications. In the event that customer uses the product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall use the product without NXP Semiconductors’ warranty of the Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification.

Product data sheet Rev. 03 — 25 February 2010 15 of 16 NXP Semiconductors 74ABT821 10-bit D-type flip-flop; positive-edge trigger; 3-state product for such automotive applications, use and specifications, and (b) whenever customer uses the product for automotive applications beyond NXP Semiconductors’ specifications such use shall be solely at customer’s own risk, and (c) customer fully indemnifies NXP Semiconductors for any liability, damages or failed product claims resulting from customer design and use of the product for automotive applications beyond NXP Semiconductors’ standard warranty and NXP Semiconductors’ product specifications.

15.4 Trademarks

Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners.16. Contact information For more information, please visit:http://www.nxp.com For sales office addresses, please send an email to:salesaddresses@nxp.com

NXP Semiconductors 74ABT821 10-bit D-type flip-flop; positive-edge trigger; 3-state © NXP B.V. 2010. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com Date of release: 25 February 2010 Document identifier: 74ABT821_3 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section ‘Legal information’. 17. Contents