74ABT541 FAIRCHILD

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 12

Technical content

Features

Output sink capability of 64mA, source capability of 32mA Guaranteed output skew Guaranteed multiple output switching specifications Output switching specified for both 50pF and 250pF loads Guaranteed simultaneous switching, noise level and dynamic threshold performance Guaranteed latchup protection High-impedance, glitch-free bus loading during entire power up and power down cycle Nondestructive, hot-insertion capability Flow-through pinout for ease of PC board layout Disable time less than enable time to avoid bus contention General Description The ABT541 is an octal buffer and line driver with 3-STATE outputs designed to be employed as a memory and address driver, clock driver, or bus-oriented trans- mitter/receiver. The ABT541 is similar to the ABT244 with broadside pinout.

Ordering Information

Devices also available in Tape and Reel. Specify by appending suffix “X” to the ordering number. Pb-Free package per JEDEC J-STD-020B. Connection Diagram Pin Descriptions Order Number Package Number Package Description 74ABT541CSC M20B 20-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-013, 0.300" Wide 74ABT541CSJ M20D 20-Lead Small Outline Package (SOP), EIAJ TYPE II, 5.3mm Wide 74ABT541CMSA MSA20 20-Lead Shrink Small Outline Package (SSOP), JEDEC MO-150, 5.3mm Wide 74ABT541CMTC MTC20 20-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 4.4mm Wide Pin Names Description OE , OE Output Enable Input (Active LOW) I Inputs O Outputs

74ABT541 Octal Buffer/Line Driver with 3-STATE Outputs ©1992 Fairchild Semiconductor Corporation www.fairchildsemi.com 74ABT541 Rev. 1.4 2 Truth Table H HIGH Voltage Level L LOW Voltage Level X Immaterial Z High Impedance Absolute Maximum Ratings Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be operable above the recommended operating conditions and stressing the parts to these levels is not recommended. In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability. The absolute maximum ratings are stress ratings only. Note: 1. Either voltage limit or current limit is sufficient to protect inputs. Recommended Operating Conditions The Recommended Operating Conditions table defines the conditions for actual device operation. Recommended operating conditions are specified to ensure optimal performance to the datasheet specifications. Fairchild does not recommend exceeding them or designing to absolute maximum ratings. Inputs OutputsOE OE I LLH H HXX Z XHX Z LLL L Symbol Parameter Rating T STG Storage Temperature –65°C to +150°C T A Ambient Temperature Under Bias –55°C to +125°C T J Junction Temperature Under Bias –55°C to +150°C V CC V CC Pin Potential to Ground Pin –0.5V to +7.0V V IN Input Voltage (1) –0.5V to +7.0V I IN Input Current (1) –30mA to +5.0mA V O Voltage Applied to Any Output Disabled or Power-Off State HIGH State –0.5V to 5.5V –0.5V to V CC Current Applied to Output in LOW State (Max.) twice the rated I OL (mA) DC Latchup Source Current –500mA Over Voltage Latchup (I/O) 10V Symbol Parameter Rating T A Free Air Ambient Temperature –40°C to +85°C V CC Supply Voltage +4.5V to +5.5V V t Minimum Input Edge Rate Data Input Enable Input 50mV/ns 20mV/ns

74ABT541 Octal Buffer/Line Driver with 3-STATE Outputs ©1992 Fairchild Semiconductor Corporation www.fairchildsemi.com 74ABT541 Rev. 1.4 3 Notes: 2. For 8-bit toggling, I CCD 0.8mA/MHz. 3. Guaranteed, but not tested. Symbol Parameter V CC Conditions Min. Typ. Max. Units V IH Input HIGH Voltage Recognized HIGH Signal 2.0 V V IL Input LOW Voltage Recognized LOW Signal 0.8 V V CD Input Clamp Diode Voltage Min. I IN –18mA –1.2 V V OH Output HIGH Voltage Min. I OH –3mA 2.5 V I OH –32mA 2.0 V V OL Output LOW Voltage Min. I OL 64mA 0.55 V I IH Input HIGH Current Max. V IN 2.7V (3) 1µ A V IN V CC I BVI Input HIGH Current Breakdown Test Max. V IN 7.0V 7 µA I IL Input LOW Current Max. V IN 0.5V (3) –1 µA V IN 0.0V –1 V ID Input Leakage Test 0.0 I ID 1.9µA, All Other Pins Grounded 4.75 V I OZH Output Leakage Current 0–5.5V V OUT 2.7V, OE n 2.0V 10 µA I OZL Output Leakage Current 0–5.5V V OUT 0.5V, OE n 2.0V –10 µA I OS Output Short-Circuit Current Max. V OUT 0.0V –100 –275 mA I CEX Output HIGH Leakage Current Max. V OUT V CC 50 µA I ZZ Bus Drainage Test 0.0 V OUT 5.5V, All Others GND 100 µA I CCH Power Supply Current Max. All Outputs HIGH 50 µA I CCL Power Supply Current Max. All Outputs LOW 30 mA I CCZ Power Supply Current Max. OE n V CC , All Others at V CC or Ground 50 µA I CCT Additional I CC /Input Outputs Enabled V I V CC – 2.1V 2.5 mA Outputs 3-STATE Max. Enable Input V I V CC – 2.1V 2.5 mA Outputs 3-STATE Data Input V I = VCC – 2.1V, All Others at VCC or Ground 50 µA ICCD Dynamic ICC No Load(3) Max Outputs Open, OE n = GND, One-Bit Toggling(2), 50% Duty Cycle 0.1 mA/ MHz

74ABT541 Octal Buffer/Line Driver with 3-STATE Outputs ©1992 Fairchild Semiconductor Corporation www.fairchildsemi.com 74ABT541 Rev. 1.4 4 SOIC package. Notes: 4. Max number of outputs defined as (n). n – 1 data inputs are driven 0V to 3V. One output at LOW. Guaranteed, but not tested. 5. Max number of outputs defined as (n). n – 1 data inputs are driven 0V to 3V. One output HIGH. Guaranteed, but not tested. 6. Max number of data inputs (n) switching. n – 1 inputs switching 0V to 3V. Input-under-test switching: 3V to threshold (VILD), 0V to threshold (VIHD). Guaranteed, but not tested. SOIC and SSOP package. Symbol Parameter V CC Conditions CL = 50pF, RL = 500Ω Min. Typ. Max. Units VOLP Quiet Output Maximum Dynamic VOL 5.0 T A = 25°C(4) 0.7 1.0 V VOLV Quiet Output Minimum Dynamic VOL 5.0 T A = 25°C(4) –1.3 –0.8 V VOHV Minimum HIGH Level Dynamic Output Voltage VIHD Minimum HIGH Level Dynamic Input Voltage VILD Maximum LOW Level Dynamic Input Voltage Symbol Parameter TA = +25°C, VCC = +5V, CL = 50pF TA = –40°C to +85°C, VCC = 4.5V–5.5V, CL = 50pF tPLH Propagation Delay, Data to Outputs

74ABT541 Octal Buffer/Line Driver with 3-STATE Outputs ©1992 Fairchild Semiconductor Corporation www.fairchildsemi.com 74ABT541 Rev. 1.4 5 Extended AC Electrical Characteristics SOIC package. Notes: 7. This specification is guaranteed but not tested. The limits apply to propagation delays for all paths described switching in phase (i.e., all LOW-to-HIGH, HIGH-to-LOW, etc.). 8. This specification is guaranteed but not tested. The limits represent propagation delay with 250pF load capacitors in place of the 50pF load capacitors in the standard AC load. This specification pertains to single output switching only. 9. This specification is guaranteed but not tested. The limits represent propagation delays for all paths described switching in phase (i.e., all LOW-to-HIGH, HIGH-to-LOW, etc.) with 250pF load capacitors in place of the 50pF load capacitors in the standard AC load. 10. The 3-STATE delays are dominated by the RC network (500Ω, 250pF) on the output and have been excluded from the datasheet. Symbol Parameter –40°C to +85°C, VCC = 4.5V to 5.5V, CL = 50pF,

8 Outputs

Switching(7) TA = –40°C to +85°C, VCC = 4.5V to 5.5V, CL = 250pF,

1 Output

Switching(8) TA = –40°C to +85°C, VCC = 4.5V to 5.5V, CL = 250pF, Switching(9) fTOGGLE Max Toggle Frequency

100 MHz

tPLH Propagation Delay, Data to Outputs tPHZ Output Disable Time 1.0 6.1 (10) ns tPLZ 1.0 5.6

74ABT541 Octal Buffer/Line Driver with 3-STATE Outputs ©1992 Fairchild Semiconductor Corporation www.fairchildsemi.com 74ABT541 Rev. 1.4 6 Skew SOIC package. Notes: 11. This specification is guaranteed but not tested. The limits apply to propagation delays for all paths described switching in phase (i.e., all LOW-to-HIGH, HIGH-to-LOW, etc.) 12. These specifications guaranteed but not tested. The limits represent propagation delays with 250pF load capacitors in place of the 50pF load capacitors in the standard AC load. 13. Skew is defined as the absolute value of the difference between the actual propagation delays for any two separate outputs of the same device. The specification applies to any outputs switching HIGH-to-LOW (tOSHL), LOW-to-HIGH (tOSLH), or any combination switching LOW-to-HIGH and/or HIGH-to-LOW (tOST). The specification is guaranteed but not tested. 14. This describes the difference between the delay of the LOW-to-HIGH and the HIGH-to-LOW transition on the same pin. It is measured across all the outputs (drivers) on the same chip, the worst (largest delta) number is the guaranteed specification. This specification is guaranteed but not tested. 15. Propagation delay variation for a given set of conditions (i.e., temperature and V CC) from device to device. This specification is guaranteed but not tested. Capacitance Note: 16. COUT is measured at frequency of f = 1 MHz, per MIL-STD-883, Method 3012. Symbol Parameter TA = –40°C to +85°C, VCC = 4.5V to 5.5V, CL = 50pF, Switching(11) TA = –40°C to +85°C, VCC = 4.5V to 5.5V, CL = 250pF, Switching(12) UnitsMax. Max. tOSHL (13) Pin to Pin Skew, HL Transitions 1.3 2.3 ns tOSLH (13) Pin to Pin Skew, LH Transitions 1.0 1.8 ns tPS (14) Duty Cycle, LH/HL Skew 2.0 3.5 ns tOST (13) Pin to Pin Skew, LH/HL Transitions 2.0 3.5 ns tPV (15) Device to Device Skew, LH/HL Transitions 2.0 3.5 ns Symbol Parameter Conditions TA = 25°C Typ. Units CIN Input Capacitance V CC = 0.0V 5.0 pF COUT (16) Output Capacitance V CC = 5.0V 9.0 pF

Dimensions are in inches (millimeters) unless otherwise noted. Figure 8. 20-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-013, 0.300" Wide

Dimensions are in millimeters unless otherwise noted. Figure 9. 20-Lead Small Outline Package (SOP), EIAJ TYPE II, 5.3mm Wide

Dimensions are in millimeters unless otherwise noted. Figure 10. 20-Lead Shrink Small Outline Package (SSOP), JEDEC MO-150, 5.3mm Wide

Dimensions are in millimeters unless otherwise noted. Figure 11. 20-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 4.4mm Wide

74ABT541 Octal Buffer/Line Driver with 3-STATE Outputs ©1992 Fairchild Semiconductor Corporation www.fairchildsemi.com 74ABT541 Rev. 1.4 12 TRADEMARKS The following are registered and unregistered trademarks Fairchild Semiconductor owns or is authorized to use and is not intended to be an exhaustive list of all such trademarks. ACEx Across the board. Around the world.¥ ActiveArray¥ Bottomless¥ Build it Now¥ CoolFET¥ CROSSVOLT¥ CTL™ Current Transfer Logic™ DOME¥ E CMOS¥ EcoSPARK EnSigna¥ FACT Quiet Series™ FACT FAST FASTr¥ FPS¥ FRFET GlobalOptoisolator¥ GTO¥ HiSeC¥ i-Lo¥ ImpliedDisconnect¥ IntelliMAX¥ ISOPLANAR¥ MICROCOUPLER¥ MicroPak¥ MICROWIRE¥ MSX¥ MSXPro¥ OCX¥ OCXPro¥ OPTOLOGIC OPTOPLANAR PACMAN¥ POP¥ Power220 Power247 PowerEdge¥ PowerSaver¥ PowerTrench Programmable Active Droop¥ QFET QS¥ QT Optoelectronics¥ Quiet Series¥ RapidConfigure¥ RapidConnect¥ ScalarPump¥ SMART START¥ SPM STEALTH™ SuperFET¥ SuperSOT¥-3 SuperSOT¥-6 SuperSOT¥-8 SyncFET™ TCM¥ The Power Franchise TinyBoost¥ TinyBuck¥ TinyLogic TINYOPTO¥ TinyPower¥ TinyWire¥ TruTranslation¥ PSerDes¥ UHC UniFET¥ VCX¥ Wire¥ DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. THESE SPECIFICATIONS DO NOT EXPAND THE TERMS OF FAIRCHILD’S WORLDWIDE TERMS AND CONDITIONS, SPECIFICALLY THE WARRANTY THEREIN, WHICH COVERS THESE PRODUCTS. LIFE SUPPORT POLICY FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user. 2. A critical component in any component of a life support, device, or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. PRODUCT STATUS DEFINITIONS Definition of Terms Datasheet Identification Product Status Definition Advance Information Formative or In Design This datasheet contains the design specifications for product development. Specifications may change in any manner without notice. Preliminary First Production This datasheet contains preliminary data; supplementary data will be published at a later date. Fairchild Semiconductor reserves the right to make changes at any time without notice to improve design. No Identification Needed Full Production This datasheet contains final specifications. Fairchild Semiconductor reserves the right to make changes at any time without notice to improve design. Obsolete Not In Production This datasheet contains specifications on a product that has been discontinued by Fairchild Semiconductor. The datasheet is printed for reference information only. Rev. I24