74ABT2240 FAIRCHILD
Document overview
- Manufacturer or author: Provided By digicamel.com
- PDF pages: 8
Technical content
Features
I Guaranteed latchup protection I High impedance glitch-free bus loading during entire power up and power down cycle I Nondestructive hot insertion capability Ordering Code: Devices also available in Tape and Reel. Specify by appending letter suffix “X” to the ordering code. Connection Diagram Schematic of Each Output Pin Descriptions Truth Table H = HIGH Voltage Level L = LOW Voltage Level X = Immaterial Z = High Impedance Order Number Package Number Package Description 74ABT2240CSC M20B 20-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-013, 0.300” Wide Body 74ABT2240CSJ M20D 20-Lead Small Outline Package (SOP), EIAJ TYPE II, 5.3mm Wide 74ABT2240CMSA MSA20 20-Lead Shrink Small Outline Package (SSOP), EIAJ TYPE II, 5.3mm Wide 74ABT2240CMTC MTC20 20-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 4.4mm Wide Pin Names Descriptions OE 1, OE2 Output Enable Input (Active LOW) D 0–D 7 Data Inputs O 0–O 7 Outputs OE 1 I0–3 O 0–3 OE 2 I4–7 O 4–7 H X Z H X Z L H L L H L L L H L L H
www.fairchildsemi.com 2 74ABT2240 Absolute Maximum Ratings(Note 1) Recommended Operating Conditions Note 1: Absolute maximum ratings are values beyond which the device may be damaged or have its useful life impaired. Functional operation under these conditions is not implied. Note 2: Either voltage limit or current limit is sufficient to protect inputs. Note 3: Guaranteed, but not tested. Note 4: For 8 bits toggling, ICCD < 0.8 mA/MHz. Storage Temperature −65°C to +150°C Ambient Temperature under Bias −55°C to +125°C Junction Temperature under Bias −55°C to +150°C VCC Pin Potential to Ground Pin −0.5V to +7.0V Input Voltage (Note 2) −0.5V to +7.0V Input Current (Note 2) −30 mA to +5.0 mA Voltage Applied to Any Output in the Disabled or Power-off State −0.5V to 5.5V in the HIGH State −0.5V to V CC Current Applied to Output in LOW State (Max) twice the rated I OL (mA) DC Latchup Source Current (Across Comm Operating Range) −300 mA Over Voltage Latchup (I/O) 10V Free Air Ambient Temperature −40°C to +85°C Supply Voltage +4.5V to +5.5V Minimum Input Edge Rate (∆V/∆t) Data Input 50 mV/ns Enable Input 20 mV/ns Symbol Parameter Min Typ Max Units VCC Conditions VIH Input HIGH Voltage 2.0 V Recognized HIGH Signal VIL Input LOW Voltage 0.8 V Recognized LOW Signal VCD Input Clamp Diode Voltage −1.2 V Min I IN = −18 mA VOH Output HIGH 2.5 V Min I OH = −3 mA Voltage 2.0 V Min I OH = −32 mA VOL Output LOW Voltage 0.8 V Min I OL = 15 mA IIH Input HIGH Current 1 µAM a x VIN = 2.7V (Note 3) 1V IN = V CC IBVI Input HIGH Current Breakdown Test 7 µAM a x V IN = 7.0V I IL Input LOW Current −1 µAM a x VIN = 0.5V (Note 3) −1V IN = 0.0V VID Input Leakage Test V 0.0 I ID = 1.9 µA All Other Pins Grounded IOZH Output Leakage Current 10 µA0 − 5.5V VOUT = 2.7V; OEn = 2.0V IOZL Output Leakage Current −10 µA0 − 5.5V VOUT = 0.5V; OEn = 2.0V IOS Output Short-Circuit Current −275 mA Max V OUT = 0.0V ICEX Output HIGH Leakage Current 50 µAM a x V OUT = V CC IZZ Bus Drainage Test 100 µA0 . 0 V OUT = 5.5V; All Others GND ICCH Power Supply Current 50 µA Max All Outputs HIGH ICCL Power Supply Current 30 mA Max All Outputs LOW ICCZ Power Supply Current 50 µAM a x OE n = V CC All Others at VCC or GND ICCT Additional Outputs Enabled 1.5 mA V I = V CC − 2.1V ICC /Input Outputs 3-STATE 1.5 mA Max Enable Input V I = VCC − 2.1V Outputs 3-STATE 50 µA Data Input V I = VCC − 2.1V All Others at VCC or GND ICCD Dynamic ICC No Load mA/ Max Outputs OPEN (Note 3) 0.1 MHz OE n = GND (Note 4) One Bit Toggling, 50% Duty Cycle
3 www.fairchildsemi.com 74ABT2240 Capacitance Note 5: C OUT is measured at frequency f = 1 MHz, per MIL-STD-883, Method 3012. Symbol Parameter TA = +25°CT A = −40°C to +85°C Units VCC = +5V V CC = 4.5V–5.5V CL = 50 pF C L = 50 pF Min Typ Max Min Max tPLH Propagation 1.0 4.9 1.0 4.9 ns tPHL Delay Data to Outputs 1.5 5.3 1.5 5.3 tPZH Output Enable 1.5 6.6 1.5 6.6 ns tPZL Time 2.7 6.9 2.7 6.9 tPHZ Output Disable 1.9 6.4 1.9 6.4 ns tPLZ Time 1.9 6.4 1.9 6.4 Symbol Parameter Typ Units Conditions TA = 25°C CIN Input Capacitance 5.0 pF V CC = 0V COUT (Note 5) Output Capacitance 9.0 pF V CC = 5.0V
5 www.fairchildsemi.com 74ABT2240 Physical Dimensions inches (millimeters) unless otherwise noted 20-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-013, 0.300” Wide Body Package Number M20B
www.fairchildsemi.com 6 74ABT2240 Physical Dimensions inches (millimeters) unless otherwise noted (Continued) 20-Lead Small Outline Package (SOP), EIAJ TYPE II, 5.3mm Wide Package Number M20D
7 www.fairchildsemi.com 74ABT2240 Physical Dimensions inches (millimeters) unless otherwise noted (Continued) 20-Lead Shrink Small Outline Package (SSOP), EIAJ TYPE II, 5.3mm Wide
www.fairchildsemi.com 8 74ABT2240 Octal Buffer/Line Driver with 25Ω Series Resistors in the Outputs Physical Dimensions inches (millimeters) unless otherwise noted (Continued) 20-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 4.4mm Wide Fairchild does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and Fairchild reserves the right at any time without notice to change said circuitry and specifications. LIFE SUPPORT POLICY FAIRCHILD ’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be rea- sonably expected to result in a significant injury to the user. 2. A critical component in any component of a life support device or system whose failure to perform can be rea- sonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. www.fairchildsemi.com