74ABT162244 NEXPERIA
Document overview
- PDF pages: 11
Technical content
Page 1
16-bit buffer/line driver with 30 Ω series termination resistors; 3-state
1. General description
The 74ABT162244 is a 16-bit buffer/line driver with 30 Ω termination resistors and 3-state outputs. The device can be used as four 4-bit buffers, two 8-bit buffers or one 16-bit buffer. The device features four output enables (1OE, 2OE, 3OE and 4OE), each controlling four of the 3-state outputs. A HIGH on nOE causes the outputs to assume a high-impedance OFF-state. This device is fully specified for partial power down applications using IOFF. The IOFF circuitry disables the output, preventing the potentially damaging backflow current through the device when it is powered down.
2. Features and benefits
- Supply voltage range from 4.5 V to 5.5 V
- BiCMOS high speed and output drive
- Direct interface with TTL levels
- Power-up 3-state
- IOFF circuitry provides partial Power-down mode operation
- Latch-up protection exceeds 500 mA per JESD78B class II level A
- 16-bit bus interface
- Multiple VCC and GND pins minimize switching noise
- 3-state buffers
- Output capability: +12 mA and -32 mA
- Live insertion and extraction permitted
- ESD protection:
- HBM JESD22-A114F exceeds 2000 V
- CDM JESD22-C101-C exceeds 1000 V
- Specified from -40 °C to +85 °C
3. Ordering information
Table 1. Ordering information
| Type number | Package | |||
|---|---|---|---|---|
| Temperature range | Name | Description | Version | |
| 74ABT162244DGG | -40 °C to +85 °C | TSSOP48 | plastic thin shrink small outline package; 48 leads; body width 6.1 mm | SOT362-1 |
Page 2
4. Functional diagram
| 47 2 36 13 1A0 1Y0 3A0 3Y0 46 3 35 14 1A1 1Y1 3A1 3Y1 44 5 33 16 1A2 1Y2 3A2 3Y2 43 6 32 17 1A3 1Y3 3A3 3Y3 1 25 1OE 3OE 41 8 30 19 2A0 2Y0 4A0 4Y0 40 9 29 20 2A1 2Y1 4A1 4Y1 38 11 27 22 2A2 2Y2 4A2 4Y2 37 12 26 23 2A3 2Y3 4A3 4Y3 48 24 2OE 4OE mna996 Fig. 1. Logic symbol | 1 1OE EN1 48 2OE EN2 25 3OE EN3 24 4OE EN4 47 2 1A0 1 1 1Y0 46 3 1A1 1Y1 44 5 1A2 1Y2 43 6 1A3 1Y3 41 8 2A0 1 2 2Y0 40 9 2A1 2Y1 38 11 2A2 2Y2 37 12 2A3 2Y3 36 13 3A0 1 3 3Y0 35 14 3A1 3Y1 33 16 3A2 3Y2 32 17 3A3 3Y3 30 19 4A0 1 4 4Y0 29 20 4A1 4Y1 27 22 4A2 4Y2 26 23 4A3 4Y3 001aae231 Fig. 2. IEC logic symbol |
|---|---|
| VCC output GND 001aac384 Fig. 3. Logic diagram one output | |
2 / 11
Page 3
5. Pinning information
5.1. Pinning

5.2. Pin description
Table 2. Pin description
| Symbol | Pin | Description |
|---|---|---|
| 1OE, 2OE, 3OE, 4OE | 1, 48, 25, 24 | 1 to 4 output enable (LOW active) |
| 1Y0, 1Y1, 1Y2, 1Y3 | 2, 3, 5, 6 | 1 data output 0 to output 3 |
| GND | 4, 10, 15, 21, 28, 34, 39, 45 | ground (0 V) |
| V CC | 7, 18, 31, 42 | supply voltage |
| 2Y0, 2Y1, 2Y2, 2Y3 | 8, 9, 11, 12 | 2 data output 0 to output 3 |
| 3Y0, 3Y1, 3Y2, 3Y3 | 13, 14, 16, 17 | 3 data output 0 to output 3 |
| 4Y0, 4Y1, 4Y2, 4Y3 | 19, 20, 22, 23 | 4 data output 0 to output 3 |
| 4A0, 4A1, 4A2, 4A3 | 30, 29, 27, 26 | 4 data input 0 to input 3 |
| 3A0, 3A1, 3A2, 3A3 | 36, 35, 33, 32 | 3 data input 0 to input 3 |
| 2A0, 2A1, 2A2, 2A3 | 41, 40, 38, 37 | 2 data input 0 to input 3 |
| 1A0, 1A1, 1A2, 1A3 | 47, 46, 44, 43 | 1 data input 0 to input 3 |
3 / 11
Page 4
6. Functional description
Table 3. Function table H = HIGH voltage level; L = LOW voltage level; X = don t care; Z = high-impedance OFF-state.
| Control | Input | Output |
| nOE | nAn | nYn |
| L | L | L |
| L | H | H |
| H | X | Z |
7. Limiting values
Table 4. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134).
| Symbol | Parameter | Conditions | Min | Max | Unit |
|---|---|---|---|---|---|
| V CC | supply voltage | -0.5 | +7.0 | V | |
| V I | input voltage | [1] | -1.2 | +7.0 | V |
| V O | output voltage | output in OFF-state or HIGH-state [1] | -0.5 | +5.5 | V |
| I IK | input clamping current | V < 0 V I | -18 | - | mA |
| I OK | output clamping current | V < 0 V O | -50 | - | mA |
| I O | output current | output in LOW-state | - | 128 | mA |
| output in HIGH-state | - | -64 | mA | ||
| T j | junction temperature | [2] | - | 150 | °C |
| T stg | storage temperature | -65 | +150 | °C |
[1] The input and output voltage ratings may be exceeded if the input and output current ratings are observed. [2] The performance capability of a high-performance integrated circuit in conjunction with its thermal environment can create junction temperatures which are detrimental to reliability.
8. Recommended operating conditions
Table 5. Operating conditions Voltages are referenced to GND (ground = 0 V).
| Symbol | Parameter | Conditions | Min | Typ | Max | Unit |
|---|---|---|---|---|---|---|
| V CC | supply voltage | 4.5 | - | 5.5 | V | |
| V I | input voltage | 0 | - | V CC | V | |
| V IH | HIGH-level input voltage | 2.0 | - | - | V | |
| V IL | LOW-level Input voltage | - | - | 0.8 | V | |
| I OH | HIGH-level output current | -32 | - | - | mA | |
| I OL | LOW-level output current | - | - | 12 | mA | |
| Δt/ΔV | input transition rise and fall rate | - | - | 10 | ns/V | |
| T amb | ambient temperature | in free air | -40 | - | +85 | °C |
4 / 11
Page 5
9. Static characteristics
Table 6. Static characteristics
| Symbol | Parameter | Conditions | 25 °C | -40 °C to +85 °C | Unit | |||
|---|---|---|---|---|---|---|---|---|
| Min | Typ | Max | Min | Max | ||||
| V IK | input clamping voltage | V = 4.5 V; I = -18 mA CC IK | - | -0.9 | -1.2 | - | -1.2 | V |
| V OH | HIGH-level output voltage | V = V or V I IL IH | ||||||
| V = 4.5 V; I = -3 mA CC OH | 2.5 | 2.9 | - | 2.5 | - | V | ||
| V = 5.0 V; I = -3 mA CC OH | 3.0 | 3.4 | - | 3.0 | - | V | ||
| V = 4.5 V; I = -32 mA CC OH | 2.0 | 2.4 | - | 2.0 | - | V | ||
| V OL | LOW-level output voltage | V = V or V I IL IH | ||||||
| V = 4.5 V; I = 8 mA CC OL | - | - | 0.65 | - | 0.65 | V | ||
| V = 4.5 V; I = 12 mA CC OL | - | - | 0.80 | - | 0.80 | V | ||
| I I | input leakage current | V = 5.5 V; V = V or GND CC I CC | - | ±0.01 | ±1.0 | - | ±1.0 | μA |
| I OFF | power-off leakage current | V = 0 V; V or V ≤ 4.5 V CC I O | - | ±5.0 | ±100 | - | ±100 | μA |
| I O(pu/pd) | power-up/power- down output current | V = 2.0 V; V = 0.5 V; [1] CC O V = GND or V ; nOE = HIGH I CC | - | ±5.0 | ±50 | - | ±50 | μA |
| I OZ | OFF-state output current | V = 5.5 V; V = V or V CC I IL IH | ||||||
| output HIGH-state at V = 5.5 V O | - | 0.1 | 10 | - | 10 | μA | ||
| output LOW-state at V = 0 V O | - | -0.1 | -10 | - | -10 | μA | ||
| I CEX | output high leakage current | HIGH-state; V = 5.5 V; O V = 5.5 V; V = GND or V CC I CC | - | 5.0 | 50 | - | 50 | μA |
| I O | output current | V = 5.5 V; V = 2.5 V [2] CC O | -50 | -100 | -180 | -50 | -180 | mA |
| I CC | supply current | V = 5.5 V; V = GND or V CC I CC | ||||||
| outputs HIGH-state | - | 0.50 | 1.0 | - | 1.0 | mA | ||
| outputs LOW-state | - | 10 | 19 | - | 19 | mA | ||
| outputs 3-state | - | 0.50 | 1.0 | - | 1.0 | mA | ||
| ΔI CC | additional supply current | per input pin; V = 5.5 V; [3] CC one input at 3.4 V and other inputs [4] at V or GND CC | - | 100 | 250 | - | 250 | μA |
| C I | input capacitance | V = 0 V or V I CC | - | 3 | - | - | - | pF |
| C I/O | input/output capacitance | outputs disabled; V = 0 V or V O CC | - | 7 | - | - | - | pF |
[1] This parameter is valid for any VCC between 0 V and 2.1 V, with a transition time of up to 10 ms. From VCC = 2.1 V to VCC = 5 V ± 10 %, a transition time of up to 100 μs is permitted. [2] Not more than one output should be tested at a time, and the duration of the test should not exceed one second. [3] This is the increase in supply current for each input at 3.4 V. [4] This data sheet limit may vary among suppliers.
5 / 11
Page 6
10. Dynamic characteristics
Table 7. Dynamic characteristics GND = 0 V. For test circuit, see Fig. 7.
| Symbol | Parameter | Conditions | 25 °C; V = 5.0 V CC | -40 °C to +85 °C; V = 5.0 V ± 0.5 V CC | Unit | |||
|---|---|---|---|---|---|---|---|---|
| Min | Typ | Max | Min | Max | ||||
| t PLH | LOW to HIGH propagation delay | nAn to nYn, see Fig. 5 | 1.0 | 1.8 | 2.4 | 1.0 | 2.7 | ns |
| t PHL | HIGH to LOW propagation delay | nAn to nYn, see Fig. 5 | 1.6 | 3.2 | 4.0 | 1.6 | 4.4 | ns |
| t PZH | OFF-state to HIGH propagation delay | nOE to nYn; see Fig. 6 | 1.2 | 2.7 | 3.5 | 1.2 | 4.3 | ns |
| t PZL | OFF-state to LOW propagation delay | nOE to nYn; see Fig. 6 | 2.6 | 5.0 | 6.2 | 2.6 | 7.3 | ns |
| t PHZ | HIGH to OFF-state propagation delay | nOE to nYn; see Fig. 6 | 1.5 | 3.0 | 3.8 | 1.5 | 4.5 | ns |
| t PLZ | LOW to OFF-state propagation delay | nOE to nYn; see Fig. 6 | 1.3 | 2.6 | 3.3 | 1.3 | 4.6 | ns |
10.1. Waveforms and test circuit


6 / 11
Page 7

Table 8. Test data
| Input | Load | V EXT | ||||||
| V I | f i | t W | t, t r f | C L | R L | t , t PHZ PZH | t , t PLZ PZL | t , t PLH PHL |
| 3.0 V | 1 MHz | 500 ns | 2.5 ns | 50 pF | 500 Ω | open | 7.0 V | open |
7 / 11
Page 8
11. Package outline
TSSOP48: plastic thin shrink small outline package; 48 leads; body width 6.1 mm
SOT362-1

Fig. 8. Package outline SOT362-1 (TSSOP48)
8 / 11
Page 9
12. Abbreviations
Table 9. Abbreviations
| Acronym | Description |
|---|---|
| BiCMOS | Bipolar Complementary Metal Oxide Semiconductor |
| CDM | Charged Device Model |
| DUT | Device Under Test |
| ESD | ElectroStatic Discharge |
| HBM | Human Body Model |
| TTL | Transistor-Transistor Logic |
13. Revision history
Table 10. Revision history
| Document ID | Release date | Data sheet status | Change notice | Supersedes |
| 74ABT162244 v.7 | 20210702 | Product data sheet | - | 74ABT162244 v.6 |
| Modifications: | • The format of this data sheet has been redesigned to comply with the identity guidelines of Nexperia. • Legal texts have been adapted to the new company name where appropriate. • Fig. 8: Package outline drawing SOT362-1 (TSSOP48) updated. • Type number 74ABT162244DL (SOT370-1/SSOP48) removed. • Section 1 and Section 2 updated. | |||
| 74ABT162244 v.6 | 20111103 | Product data sheet | - | 74ABT162244 v.5 |
| Modifications: | • Legal pages updated | |||
| 74ABT162244 v.5 | 20100525 | Product data sheet | - | 74ABT162244 v.4 |
| 74ABT162244 v.4 | 20090409 | Product data sheet | - | 74ABT_H162244 v.3 |
| 74ABT_H162244 v.3 | 19981022 | Product specification | - | 74ABT_H162244 v.2 |
| 74ABT_H162244 v.2 | 19980225 | Product specification | - | 74ABT_H162244 v.1 |
| 74ABT_H162244 v.1 | 19961023 | Product specification | - | - |
9 / 11
Page 10
14. Legal information
Data sheet status
| Document status [1][2] | Product status [3] | Definition |
| Objective [short] data sheet | Development | This document contains data from the objective specification for product development. |
| Preliminary [short] data sheet | Qualification | This document contains data from the preliminary specification. |
| Product [short] data sheet | Production | This document contains the product specification. |
[1] Please consult the most recently issued document before initiating or completing a design. [2] The term 'short data sheet' is explained in section "Definitions". [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the internet at https://www.nexperia.com.
Definitions
Draft — The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. Nexperia does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information.
Short data sheet — A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local Nexperia sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail.
Product specification — The information and data provided in a Product data sheet shall define the specification of the product as agreed between Nexperia and its customer, unless Nexperia and customer have explicitly agreed otherwise in writing. In no event however, shall an agreement be valid in which the Nexperia product is deemed to offer functions and qualities beyond those described in the Product data sheet.
Disclaimers
Limited warranty and liability — Information in this document is believed to be accurate and reliable. However, Nexperia does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. Nexperia takes no responsibility for the content in this document if provided by an information source outside of Nexperia.
In no event shall Nexperia be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory.
Notwithstanding any damages that customer might incur for any reason whatsoever, Nexperia’s aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of Nexperia.
Right to make changes — Nexperia reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof.
Suitability for use — Nexperia products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or malfunction of an Nexperia product can reasonably be expected to result in personal
injury, death or severe property or environmental damage. Nexperia and its suppliers accept no liability for inclusion and/or use of Nexperia products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk.
Quick reference data — The Quick reference data is an extract of the product data given in the Limiting values and Characteristics sections of this document, and as such is not complete, exhaustive or legally binding.
Applications — Applications that are described herein for any of these products are for illustrative purposes only. Nexperia makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification.
Customers are responsible for the design and operation of their applications and products using Nexperia products, and Nexperia accepts no liability for any assistance with applications or customer product design. It is customer’s sole responsibility to determine whether the Nexperia product is suitable and fit for the customer’s applications and products planned, as well as for the planned application and use of customer’s third party customer(s). Customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products.
Nexperia does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer’s applications or products, or the application or use by customer’s third party customer(s). Customer is responsible for doing all necessary testing for the customer’s applications and products using Nexperia products in order to avoid a default of the applications and the products or of the application or use by customer’s third party customer(s). Nexperia does not accept any liability in this respect.
Limiting values — Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the device. Limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the Recommended operating conditions section (if present) or the Characteristics sections of this document is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device.
Terms and conditions of commercial sale — Nexperia products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nexperia.com/profile/terms, unless otherwise agreed in a valid written individual agreement. In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. Nexperia hereby expressly objects to applying the customer’s general terms and conditions with regard to the purchase of Nexperia products by customer.
No offer to sell or license — Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights.
Export control — This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from competent authorities.
Non-automotive qualified products — Unless this data sheet expressly states that this specific Nexperia product is automotive qualified, the product is not suitable for automotive use. It is neither qualified nor tested in accordance with automotive testing or application requirements. Nexperia accepts no liability for inclusion and/or use of non-automotive qualified products in automotive equipment or applications.
In the event that customer uses the product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall use the product without Nexperia’s warranty of the product for such automotive applications, use and specifications, and (b) whenever customer uses the product for automotive applications beyond Nexperia’s specifications such use shall be solely at customer’s own risk, and (c) customer fully indemnifies Nexperia for any liability, damages or failed product claims resulting from customer design and use of the product for automotive applications beyond Nexperia’s standard warranty and Nexperia’s product specifications.
Translations — A non-English (translated) version of a document is for reference only. The English version shall prevail in case of any discrepancy between the translated and English versions.
Trademarks
Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners.
10 / 11
Page 11
Contents
- General description......................................................1 2. Features and benefits.................................................. 1 3. Ordering information....................................................1 4. Functional diagram.......................................................2 5. Pinning information......................................................3 5.1. Pinning.........................................................................3 5.2. Pin description.............................................................3 6. Functional description................................................. 4 7. Limiting values............................................................. 4
- Recommended operating conditions..........................4 9. Static characteristics....................................................5 10. Dynamic characteristics............................................ 6 10.1. Waveforms and test circuit........................................ 6 11. Package outline.......................................................... 8 12. Abbreviations..............................................................9 13. Revision history..........................................................9 14. Legal information......................................................10
For more information, please visit: http://www.nexperia.com For sales office addresses, please send an email to: salesaddresses@nexperia.com Date of release: 2 July 2021
11 / 11