74ABT08 PHILIPS

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 10

Technical content

/C0109 /C0110 /C0114 74ABT08 Quad 2-input AND gate Product specification 1995 Sep 18 INTEGRATED CIRCUITS IC23 Data Handbook

Philips Semiconductors Product specification 74ABT08Quad 2-input AND gate

21995 Sep 18 853-1806 15752

Tamb = 25°C; GND = 0V TYPICAL UNIT tPLH tPHL Propagation delay An or Bn to Yn C L = 50pF; VCC =5 V 2.4 1.9 ns tOSLH tOSHL Output to Output skew VCC = 5V 0.4 ns C IN Input capacitance VI = 0V or VCC 3 pF ICC Total supply current Outputs disabled; V CC = 5.5V 50 µA PIN CONFIGURATION GND VCC SA00342 LOGIC SYMBOL B1A0 B0 A1 A2 B2 A3 B3 Y0 Y1 Y2 Y3 368 1 1 12 4 5 9 1 0 1 2 1 3 VCC = Pin 14 GND = Pin 7 SA00343 LOGIC DIAGRAM Y3VCC = Pin 14 GND = Pin 7 SA00344 PIN DESCRIPTION PIN NUMBER SYMBOL NAME AND FUNCTION 1, 2, 4, 5, 9, 10, 12, 13 An-Bn Data inputs 3, 6, 8, 11 Yn Data outputs

7 GND Ground (0V)

14 VCC Positive supply voltage

LOGIC SYMBOL (IEEE/IEC) SA00363 FUNCTION TABLE INPUTS OUTPUT An Bn Yn L L L L H L H L L H H H NOTES: H = High voltage level L = Low voltage level

ORDERING INFORMATION

PACKAGES TEMPERATURE RANGE OUTSIDE NORTH AMERICA NORTH AMERICA DWG NUMBER 14-Pin Plastic DIP –40°C to +85°C 74ABT08 N 74ABT08 N SOT27-1 14-Pin plastic SO –40°C to +85°C 74ABT08 D 74ABT08 D SOT108-1 14-Pin Plastic SSOP Type II –40°C to +85°C 74ABT08 DB 74ABT08 DB SOT337-1 14-Pin Plastic TSSOP Type I –40°C to +85°C 74ABT08 PW 74ABT08PW DH SOT402-1

Philips Semiconductors Product specification 74ABT08Quad 2-input AND gate

1995 Sep 18 3

ABSOLUTE MAXIMUM RATINGS 1, 2 SYMBOL PARAMETER CONDITIONS RATING UNIT VCC DC supply voltage –0.5 to +7.0 V IIK DC input diode current VI < 0 –18 mA VI DC input voltage3 –1.2 to +7.0 V IOK DC output diode current VO < 0 –50 mA VOUT DC output voltage3 output in Off or High state –0.5 to +5.5 V IOUT DC output current output in Low state 40 mA Tstg Storage temperature range –65 to 150 °C NOTES: 1. Stresses beyond those listed may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 2. The performance capability of a high-performance integrated circuit in conjunction with its thermal environment can create junction temperatures which are detrimental to reliability. The maximum junction temperature of this integrated circuit should not exceed 150°C. 3. The input and output voltage ratings may be exceeded if the input and output current ratings are observed. RECOMMENDED OPERATING CONDITIONS SYMBOL PARAMETER LIMITS UNITSYMBOL PARAMETER MIN MAX UNIT VCC DC supply voltage 4.5 5.5 V VI Input voltage 0 VCC V VIH High-level input voltage 2.0 V VIL Low-level input voltage 0.8 V IOH High-level output current –15 mA IOL Low-level output current 20 mA Δt/Δv Input transition rise or fall rate 0 5 ns/V Tamb Operating free-air temperature range –40 +85 °C DC ELECTRICAL CHARACTERISTICS LIMITS SYMBOL PARAMETER TEST CONDITIONS Tamb = +25°C Tamb = –40°C to +85°C UNIT MIN TYP MAX MIN MAX VIK Input clamp voltage VCC = 4.5V; IIK = –18mA –0.9 –1.2 –1.2 V VOH High-level output voltageVCC = 4.5V; IOH = –15mA; VI = VIL or VIH 2.5 2.9 2.5 V VOL Low-level output voltage VCC = 4.5V; IOL = 20mA; VI = VIL or VIH 0.35 0.5 0.5 V IOFF Power-off leakage currentVCC = 0.0V; VO or VI ≤ 4.5V ±5.0 ±100 ±100 µA ICEX Output High leakage currentVCC = 5.5V; VO = 5.5V; VI = GND or VCC 5.0 50 50 µA IO Output current1 VCC = 5.5V; VO = 2.5V –50 –75 –180 –50 –180 mA ICC Quiescent supply current VCC = 5.5V; VI = GND or VCC 2 50 50 µA ΔICC Additional supply current per input pin2 VCC = 5.5V; One data input at 3.4V, other inputs at VCC or GND 0.25 500 500 µA NOTES: 1. Not more than one output should be tested at a time, and the duration of the test should not exceed one second. 2. This is the increase in supply current for each input at 3.4V.

Philips Semiconductors Product specification 74ABT08Quad 2-input AND gate

1995 Sep 18 4

GND = 0V; tR = tF = 2.5ns; CL = 50pF, RL = 500Ω LIMITS SYMBOL PARAMETER WAVEFORM Tamb = +25°C VCC = +5.0V Tamb = –40°C to +85°C VCC = +5.0V ±0.5V UNIT MIN TYP MAX MIN MAX tPLH tPHL Propagation delay An or Bn to Yn 1 1.0 1.0 2.4 1.9 3.4 2.8 1.0 1.0 4.0 3.0 ns tOSHL tOSLH 1 Output to Output skew An or Bn to Yn 2 0.4 0.4 0.5 0.5 0.5 0.5 ns NOTE: 1. Skew is defined as the absolute value of the difference between the actual propagation delay for any two separate outputs of the same device. The specification applies to any outputs switching in the the same direction, either HIGH-to-LOW (tOSHL ) or LOW-to-HIGH (tOSLH ); parameter guaranteed by design. AC WAVEFORMS VM = 1.5V, VIN = GND to 3.0V VMVM VMVM Yn An, Bn tPHL tPLH SA00345 Waveform 1. Propagation Delay for Non-Inverting Outputs OUTPUT N same part INPUT SA00381 OUTPUT tPLH MIN tPHL MIN tPLH MAX tPHL MAX tOSLH tOSHL Waveform 2. Common edge skew TEST CIRCUIT AND WAVEFORMS PULSE GENERATOR R T VIN D.U.T. VOUT C L R L VCC Test Circuit for Outputs VM VM tW AMP (V) NEGATIVE PULSE 10% 10% 90% 90% VM VM tW AMP (V) POSITIVE PULSE 90% 90% 10% 10% tTHL (tF) tTLH (tR )t THL (tF) tTLH (tR ) VM = 1.5V Input Pulse Definition DEFINITIONS R L = Load resistor; see AC CHARACTERISTICS for value. C L = Load capacitance includes jig and probe capacitance; see AC CHARACTERISTICS for value. R T = Termination resistance should be equal to ZOUT of pulse generators. INPUT PULSE REQUIREMENTS FAMILY 74ABT SH00067 Amplitude Rep. Rate t W tF 3.0V 1MHz 500ns 2.5ns tR 2.5ns

Philips Semiconductors Product specification 74ABT08Quad 2-input AND gate

1995 Sep 18 5

DIP14: plastic dual in-line package; 14 leads (300 mil) SOT27-1

Philips Semiconductors Product specification 74ABT08Quad 2-input AND gate

1995 Sep 18 6

SO14: plastic small outline package; 14 leads; body width 3.9 mm SOT108-1

Philips Semiconductors Product specification 74ABT08Quad 2-input AND gate

1995 Sep 18 7

SSOP14: plastic shrink small outline package; 14 leads; body width 5.3 mm SOT337-1

Philips Semiconductors Product specification 74ABT08Quad 2-input AND gate

1995 Sep 18 8

TSSOP14: plastic thin shrink small outline package; 14 leads; body width 4.4 mm SOT402-1

Philips Semiconductors Product specification 74ABT08Quad 2-input AND gate

1995 Sep 18 9

Philips Semiconductors Product specification 74ABT08Quad 2-input AND gate Philips Semiconductors and Philips Electronics North America Corporation reserve the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. LIFE SUPPORT APPLICATIONS Philips Semiconductors and Philips Electronics North America Corporation Products are not designed for use in life support appliances, devices, or systems where malfunction of a Philips Semiconductors and Philips Electronics North America Corporation Product can reasonably be expected to result in a personal injury. Philips Semiconductors and Philips Electronics North America Corporation customers using or selling Philips Semiconductors and Philips Electronics North America Corporation Products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors and Philips Electronics North America Corporation for any damages resulting from such improper use or sale. This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips Semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. Philips Semiconductors

811 East Arques Avenue

P.O. Box 3409 Sunnyvale, California 94088–3409 Telephone 800-234-7381 DEFINITIONS Data Sheet Identification Product Status Definition Objective Specification Preliminary Specification Product Specification Formative or in Design Preproduction Product Full Production This data sheet contains the design target or goal specifications for product development. Specifications may change in any manner without notice. This data sheet contains Final Specifications. Philips Semiconductors reserves the right to make changes at any time without notice, in order to improve design and supply the best possible product. Philips Semiconductors and Philips Electronics North America Corporation register eligible circuits under the Semiconductor Chip Protection Act.  Copyright Philips Electronics North America Corporation 1995 All rights reserved. Printed in U.S.A.