6809

6809 ALLEGRO

Document overview

• Manufacturer or author: Provided By www.digicamel.com(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 8

Technical content

DABiC-IV , 10-BIT SERIAL-INPUT, LATCHED SOURCE DRIVERS A6810xA Data Sheet26182.124B ABSOLUTE MAXIMUM RATINGS at TA = 25°C Continuous Output Current Range, Input Voltage Range, Package Power Dissipation, Operating Temperature Range, T A Storage Temperature Range, Caution: These CMOS devices have input static protection (Class 2) but are still susceptible to damage if exposed to extremely high static electrical charges. The A6809– and A6810– devices combine 10-bit CMOS shift registers, accompanying data latches and control circuitry with bipolar sourcing outputs and pnp active pull downs. Designed primarily to drive vacuum-fluorescent displays, the 60 V and -40 mA output ratings also allow these devices to be used in many other peripheral power driver applications. The A6809– and A6810– feature an increased data input rate (compared with the older UCN/UCQ5810-F) and a con- trolled output slew rate. The A6809xLW and A6810xLW are identical except for pinout. The CMOS shift register and latches allow direct interfacing with microprocessor-based systems. With a 3.3 V or 5 V logic supply, typical serial-data input rates are up to 33 MHz. A CMOS serial data output permits cascade connections in applica- tions requiring additional drive lines. Similar devices are avail-able as the A6811– (12 bits), A6812– (20 bits), and A6818– (32 bits). The A6809– and A6810– output source drivers are npn Darling- tons, capable of sourcing up to 40 mA. The controlled output slew rate reduces electromagnetic noise, which is an important consideration in systems that include telecommunications and/or microprocessors and to meet government emissions regulations. For inter-digit blanking, all output drivers can be disabled and all sink drivers turned on with a BLANKING input high. The pnp active pull-downs will sink at least 2.5 mA. All devices are available in two temperature ranges for optimum performance in commercial (suffix S-) or industrial (suffix E-) applica- tions. The A6810– is provided in three package styles for through-hole DIP (suffix -A), surface-mount SOIC (suffix -LW), or minimum-area surface-mount PLCC (suffix -EP). The A6809– is provided in the SOIC (suffix -LW) only. Copper lead frames, low logic-power dissi- pation, and low output-saturation voltages allow all devices to source 25 mA from all outputs continuously over the maximum operating temperature range.

FEATURES

I Controlled Output Slew Rate I High-Speed Data Storage I 60 V Minimum Output Breakdown I High Data Input Rate I PNP Active Pull-Downs Complete part number includes a suffix to identify operating temperature range (E- or S-) and package type (-A, -EP, or -LW). Always order by complete part number, e.g., A6810SLW .

6809 AND

I Low Output-Saturation Voltages I Low-Power CMOS Logic and Latches I Improved Replacements for TL4810–, UCN5810–, and UCQ5810– 91 0 SERIAL DATA OUT LOAD SUPPLY SERIAL DATA IN BLANKINGLOGIC SUPPLY STROBE GROUND CLOCK CLK V ST BLNK DD BBV OUT 9 OUT 10 OUT1 OUT 2 OUT 3 Dwg. PP-029 OUT8 OUT7 OUT6 OUT 5 OUT4 LATCHES REGISTER REGISTER LATCHES

6809 AND 6810

10-BIT SERIAL-INPUT, LATCHED SOURCE DRIVERS

115 Northeast Cutoff, Box 15036

Worcester, Massachusetts 01615-0036 (508) 853-5000 Copyright © 1998, 2000 Allegro MicroSystems, Inc. A6810xEP TYPICAL OUTPUT DRIVER TYPICAL INPUT CIRCUIT A6809xLW SERIAL DATA OUT LOAD SUPPLY SERIAL DATA IN BLANKINGBLNK V OUT1 OUT2 OUT3 REGISTER LATCHES LOGIC SUPPLY STROBE V ST DD OUT 5 OUT 4 GROUND CLOCK CLK BB OUT9 OUT10 Dwg. PP-029-9 OUT 8 OUT7 OUT 6 LATCHES REGISTER 10 11 NO CONNECTION NC NO CONNECTIONNC A6810xLW SERIAL DATA OUT LOAD SUPPLY SERIAL DATA IN BLANKING OUT OUT10 OUT1 OUT2 OUT3 11 NO CONNECTION LOGIC SUPPLY STROBE GROUND CLOCK OUT8 OUT7 OUT 6 OUT 5 OUT 4 10NO CONNECTION CLK V ST BLNKDD BBV Dwg. PP-029-2 LATCHES REGISTER REGISTER LATCHES NCNC 13 19 STROBE V DD Dwg. PP-059 OUT1 OUT10 OUT5 OUT6 LATCHES REGISTER REGISTER LATCHES V BB CLOCK NC GROUND LOGIC SUPPLY SERIAL DATA OUT LOAD SUPPLY NC SERIAL DATA IN BLANKINGST CLK BLNK 50 75 100 125 150 2.5 0.5 ALLOWABLE PACKAGE POWER DISSIPATION IN WATTS AMBIENT TEMPERATURE IN °C 2.0 1.5 1.0 SUFFIX 'A', R = 60°C/WθJA SUFFIX 'EP', R = 59°C/WθJA Dwg. GP-024-1 SUFFIX 'LW', R = 70°C/WθJA Dwg. EP-010-5 IN VDDVBB Dwg. EP-021-19 OUTN

10-BIT SERIAL-INPUT, LATCHED SOURCE DRIVERS www.allegromicro.com FUNCTIONAL BLOCK DIAGRAM TRUTH TABLE Serial Shift Register Contents Serial Latch Contents Output Contents Data Clock Data Strobe Input Input I HH R 1 R2 ... R N-2 RN-1 RN-1 LL R 1 R2 ... R N-2 RN-1 RN-1 XR 1 R2 R3 ... R N-1 RN RN L = Low Logic Level H = High Logic Level X = Irrelevant P = Present State R = Previous State MOS BIPOLAR OUT 1 OUT 2GROUND Dwg. FP-013-1OUT 3 OUT N CLOCK SERIAL DATA IN STROBE BLANKING SERIAL DATA OUTSERIAL-PARALLEL SHIFT REGISTER LATCHES VDD VBB LOGIC SUPPLY LOAD SUPPLY

10-BIT SERIAL-INPUT, LATCHED SOURCE DRIVERS Worcester, Massachusetts 01615-0036 (508) 853-5000 Limits @ VDD = 3.3 V Limits @ V DD = 5 V Output Leakage Current I CEX VOUT = 0 V — <-0.1 -15 — <-0.1 -15 µA Output Voltage V OUT(1) IOUT = -25 mA 57.5 58.3 — 57.5 58.3 — V VOUT(0) IOUT = 1 mA — 1.0 1.5 — 1.0 1.5 V Output Pull-Down Current I OUT(0) VOUT = 5 V to VBB 2.5 5.0 — 2.5 5.0 — mA Input Voltage V IN(1) 2.2 —— 3.3 —— V Input Current I IN(1) VIN = VDD — <0.01 1.0 — <0.01 1.0 µA Input Clamp Voltage V IK IIN = -200 µA — -0.8 -1.5 — -0.8 -1.5 V Serial Data Output Voltage V OUT(1) IOUT = -200 µA 2.8 3.05 — 4.5 4.75 — V VOUT(0) IOUT = 200 µA — 0.15 0.3 — 0.15 0.3 V Maximum Clock Frequency f c 10 33 — 10 33 — MHz Logic Supply Current I DD(1) All Outputs High — 0.25 0.75 — 0.3 1.0 mA IDD(0) All Outputs Low — 0.25 0.75 — 0.3 1.0 mA Load Supply Current I BB(1) All Outputs High, No Load — 1.5 3.0 — 1.5 3.0 mA IBB(0) All Outputs Low — 0.2 20 — 0.2 20 µA Blanking-to-Output Delay t dis(BQ) CL = 30 pF, 50% to 50% — 0.7 2.0 — 0.7 2.0 µs ten(BQ) CL = 30 pF, 50% to 50% — 1.8 3.0 — 1.8 3.0 µs Output Fall Time t f RL = 2.3 kΩ, CL ≤ 30 pF 2.4 — 12 2.4 — 12 µs Output Rise Time t r RL = 2.3 kΩ, CL ≤ 30 pF 2.4 — 12 2.4 — 12 µs Output Slew Rate dV/dt R L = 2.3 kΩ, CL ≤ 30 pF 4.0 — 20 4.0 — 20 V/ µs Clock-to-Serial Data Out Delay t p(CH-SQX) IOUT = ±200 µA — 50 —— 50 — ns Negative current is defined as coming out of (sourcing) the specified device terminal. Typical data is is for design information only and is at T A = +25°C. ELECTRICAL CHARACTERISTICS at TA = +25°C (A6809SLW & A6810S-) or over operating temperature range (A6809ELW & A6810E-), VBB = 60 V unless otherwise noted.

10-BIT SERIAL-INPUT, LATCHED SOURCE DRIVERS www.allegromicro.com TIMING REQUIREMENTS and SPECIFICATIONS (Logic Levels are VDD and Ground) Serial Data present at the input is transferred to the shift register on the logic “0” to logic “1” transition of the CLOCK input pulse. On succeeding CLOCK pulses, the registers shift data information towards the SERIAL DATA OUTPUT. The SERIAL DATA must appear at the input prior to the rising edge of the CLOCK input waveform. Information present at any register is transferred to the respective latch when the STROBE is high (serial-to-parallel conversion). The latches will continue to accept new data as long as the STROBE is held high. Applications where the latches are bypassed (STROBE tied high) will require that the BLANKING input be high during serial data entry. When the BLANKING input is high, the output source drivers are disabled (OFF); the pnp active pull-down sink drivers are ON. The information stored in the latches is not affected by the BLANKING input. With the BLANKING input low, the outputs are controlled by the state of their respective latches. CLOCK SERIAL DATA IN STROBE BLANKING OUTN Dwg. WP-029 50%SERIAL DATA OUT DATA DATA 10% 90% 50% 50% 50% C A B D E LOW = ALL OUTPUTS ENABLED p(STH-QL)t p(CH-SQX)t DATA p(STH-QH)t BLANKING OUTN Dwg. WP-030 DATA 10% 50% en(BQ)t dis(BQ)t HIGH = ALL OUTPUTS BLANKED (DISABLED) 90% rt ft A. Data Active Time Before Clock Pulse B. Data Active Time After Clock Pulse NOTE – Timing is representative of a 10 MHz clock. Signifi- cantly higher speeds are attainable.

10-BIT SERIAL-INPUT, LATCHED SOURCE DRIVERS Worcester, Massachusetts 01615-0036 (508) 853-5000 A6810EA & A6810SA Dimensions in Inches (controlling dimensions) Dimensions in Millimeters (for reference only) NOTES: 1. Exact body and lead configuration at vendor ’s option within limits shown. 2. Lead spacing tolerance is non-cumulative. 3. Lead thickness is measured at seating plane or below. 0.014 0.008 0.300 BSC Dwg. MA-001-18A in 0.430 MAX 1 9 0.280 0.240 0.210 MAX 0.070 0.045 0.015 MIN 0.022 0.014 0.100 BSC 0.005 MIN 0.150 0.115 0.920 0.880 0.355 0.204 7.62 BSC Dwg. MA-001-18A mm 10.92 MAX 1 9 7.11 6.10 5.33 MAX 1.77 1.15 0.39 MIN 0.558 0.356 2.54 BSC 0.13 MIN 3.81 2.93 23.37 22.35

10-BIT SERIAL-INPUT, LATCHED SOURCE DRIVERS www.allegromicro.com A6810EEP & A6810SEP Dimensions in Inches (controlling dimensions) Dimensions in Millimeters (for reference only) NOTES: 1. Exact body and lead configuration at vendor ’s option within limits shown. 2. Lead spacing tolerance is non-cumulative. The products described here are manufactured under one or more Allegro MicroSystems, Inc. reserves the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the performance, reliability, or manufacturability of its products. Before placing an order, the user is cautioned to verify that the information being relied upon is current. Allegro products are not authorized for use as critical components in life-support devices or systems without express written approval. The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, Inc. assumes no responsi- bility for its use; nor for any infringement of patents or other rights of third parties which may result from its use. 913 0.020 MIN 0.180 0.165 0.050 BSC 120 2 Dwg. MA-005-20A in 0.395 0.385 0.356 0.350 0.032 0.026 0.021 0.013 814 0.356 0.350 0.395 0.385 INDEX AREA 0.169 0.141 0.169 0.141 913 0.51 MIN 4.57 4.20 1.27 BSC 120 2 Dwg. MA-005-20A mm 10.03 9.78 9.042 8.890 0.812 0.661 0.533 0.331 814 9.042 8.890 10.03 9.78 INDEX AREA 4.29 3.58 4.29 3.58

10-BIT SERIAL-INPUT, LATCHED SOURCE DRIVERS Worcester, Massachusetts 01615-0036 (508) 853-5000 A6809ELW, A6809SLW, A6810ELW, & A6810SLW Dimensions in Inches (for reference only) Dimensions in Millimeters (controlling dimensions) NOTES: 1. Exact body and lead configuration at vendor ’s option within limits shown. 2. Lead spacing tolerance is non-cumulative. 0° TO 8° 1 2 30.020 0.013 0.0040 MIN. 0.0125 0.0091 0.050 0.016 Dwg. MA-008-20 in 0.050 BSC 20 11 0.2992 0.2914 0.419 0.394 0.5118 0.49610.0926 0.1043 0° TO 8° 2 30.51 0.33 0.10 MIN. Dwg. MA-008-20 mm 1.27 BSC 0.32 0.23 1.27 0.40 7.60 7.40 10.65 10.00 13.00 12.602.65 2.35