6017W2PAM61B30X CONEC
Document overview
- Manufacturer or author: Provided By www.digicamel.com(free datasheet download site)
- PDF pages: 2
Technical content
dim. in mm RR RR date drawn THIS DRAW ING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH d-old norm appd. tolerance material: title: dwg no: DIN- sh: part no: namedate namedescriptionrev.DO NOT ALTER CAD DRAWING BY HAND scale: 15K1A1247 D-SUB COMBINATION MALE SEE NOTES Henneboel07.12.12
07.12.12 Fischer
threaded insert and hexlocking screw 2:1 6017W2PAM61B30X a Original 38,86-0,02 0,23+ 61,4-0 0,3+ 21,1 -00,3 10° 4-40 UNC SEE NOTE 14 AT ALL TIMES WATER RESISTANT CONNECTORS NOT IN USE SHOULD BE COVERED WITH A CONEC WATER RESISTANT CAP OR WATER TIGHT HOOD. POS. 1 POS. 8 O-RING 4-40 UNC SEE NOTE 9 4,6 9,4 8,26-0,03 0,22+ 5,7 -0,18 0,12 3,6 -00,25 7,1 0,3 4,8SW RUBBER GASKET PLACED ON TOP SURFACE OF MALE INSULATOR NOTES: 1. RECOMMENDED SOLDER INSTRUCTION SEE SHEET 2 2. METALSHELLS: COPPER ALLOY; min. 315µin TIN over 40-80µin NICKEL 3. INSULATORS: PBT GF UL 94 V-0, GREEN 4. SIGNAL CONTACTS: COPPER ALLOY PLATING :GOLD FLASH over NICKEL SOLDER CUP ACCEPTS CABLE AWG 20 5. HIGH POWER CONTACTS 10A: COPPER ALLOY PLATING MATING AREA: GOLD FLASH over NICKEL PLATING TERMINATION SIDE: 160-240µin TIN over 80µin NICKEL SOLDER CUP ACCEPTS CABLE AWG 16-20 6. THREADED INSERTS: COPPER ALLOY; min. 200µin TIN over 80µin NICKEL 7. COLLARS: COPPER ALLOY; 200µin TIN over 80µin NICKEL 8. HEXLOCKING SCREWS: STAINLESS STEEL 9. FRAME: ZINC DIE CAST; NICKEL PLATED 10. O-RING: SILICONE; BLUE 11. RUBBER: GASKET; TPE 12. RECOMMENDED PANEL CUT-OUT ON SHEET 2 13. RECOMMENDED TORQUE FOR MOUNTING SCREW 35N cm 14. CONNECTOR IS PART MARKED: 6017W2PAM61B30X CO NEC ABC Directive 2002/95/EC RoHS compliant 1,12Ø (15x) POS. A1 14,24 -0,38 0,12 + SEALING COMPOUND ( 5 : 1 ) 47,04\` 0,13 1,8Ø (2x)
dim. in mm RR RR date drawn THIS DRAW ING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH d-old norm appd. tolerance material: title: dwg no: DIN- sh: part no: namedate namedescriptionrev.DO NOT ALTER CAD DRAWING BY HAND scale: 15K1A1247 PANEL CUT-OUT see sheet1 Henneboel07.12.12 D-SUB COM. MALE 17W2P SOLDER CUP with threaded insert and hexlocking screw 2:1 SEE SHEET 1 a Original 42,5\ 0,1 47,04\ 0,1 3,1 0,05 n (2x) 10°\ 1° 11,4 0,1 3,4 R \ 0,13 i 0,26B i 0,26A B A RECOMMENDED PANEL CUT-OUT Solder Instruction 1. Cable should be prepared for soldering. The cable/wires must be pretinned. 2. Insert cable/wire into solder cup. 3. Signal Contact 3.1. Operate the soldering iron at 350° C, 50 Watt max. and use a pencil tip. 3.2. Put tip to wire in solder cup. 3.3. After 1 second bring in solder. 3.4. Heat for 3 seconds longer. Do not heat contact more than 4 seconds in total. 4. Power Contact 4.1. Operate the soldering iron at 350° C, 100 Watt max. and use a pencil tip. 4.2. Put tip to wire in solder cup. 4.3. After 1 second bring in solder. 4.4. Heat for 5 seconds longer. Do not heat contact more than 6 seconds in total. 5. Remove soldering iron. 6. Wait until solder gets rigid again. 7. Do not solder adjacent contacts consecutively, alternate position within the connector to minimize heat build up.