DATASHEET SEARCH SITE

Document overview

  • PDF pages: 8

Technical content

Page 1

Technical Data

RF Power GaN Transistor

Document Number: A3G26H350W17S

Rev. 1, 01/2021

PDF page 1 diagram

This 59 W asymmetrical Doherty RF power GaN transistor is designed for cellular base station applications requiring very wide instantaneous bandwidth capability covering the frequency range of 2496 to 2690 MHz. This part is characterized and performance is guaranteed for applications

PDF page 1 diagram

operating in the 2496 to 2690 MHz band. There is no guarantee of performance when this part is used in applications designed outside of these frequencies.

2600 MHz  Typical Doherty Single--Carrier W--CDMA Performance: VDD = 48 Vdc, IDQA = 250 mA, VGSB = –5.5 Vdc, Pout = 59 W Avg., Input Signal

PDF page 1 diagram

PAR = 9.9 dB @ 0.01% Probability on CCDF.

Frequency Gps (dB) D (%) Output PAR (dB) ACPR (dBc)
2496 MHz 13.3 49.9 8.9 –33.2
2590 MHz 13.5 48.5 9.1 –37.2
2690 MHz 13.3 48.5 8.9 –34.5
PDF page 1 diagram

Features

 High terminal impedances for optimal broadband performance  Advanced high performance in--package Doherty  Improved linearized error vector magnitude with next generation signal  Able to withstand extremely high output VSWR and broadband operating conditions

PDF page 1 diagram

Page 2

Table 1. Maximum Ratings

Rating Symbol Value Unit
Drain--Source Voltage VDSS 125 Vdc
Gate--Source Voltage VGS –8, 0 Vdc
Operating Voltage VDD 55 Vdc
Maximum Forward Gate Current, IG (A+B), @ TC = 25C IGMAX 58 mA
Storage Temperature Range Tstg –65 to +150 C
Case Operating Temperature Range TC –55 to +150 C
Maximum Channel Temperature TCH 225 C

Table 2. Recommended Operating Conditions

Rating Symbol Value Unit
Operating Voltage VDD 48 Vdc

Table 3. Thermal Characteristics

Characteristic Symbol Value Unit
Thermal Resistance by Infrared Measurement, Active Die Surface--to--Case Case Temperature 84C, PD = 73 W R JC (IR) 0.70 (1) C/W
Thermal Resistance by Finite Element Analysis, Channel--to--Case Case Temperature 90C, PD = 73 W R CHC (FEA) 1.10 (2) C/W

Table 4. ESD Protection Characteristics

Test Methodology Class
Human Body Model (per JS--001--2017) 1B
Charge Device Model (per JS--002--2014) C3

Table 5. Electrical Characteristics (TA = 25C unless otherwise noted)

Symbol

Min Typ Max Unit

Characteristic

Off Characteristics (3) Drain--Source Breakdown Voltage

V(BR)DSS

— — Vdc

(VGS = –8 Vdc, ID = 16.2 mAdc)

Carrier

150

(VGS = –8 Vdc, ID = 42 mAdc)

150

Peaking

On Characteristics — Side A, Carrier

Gate Threshold Voltage (VDS = 10 Vdc, ID = 16.2 mAdc) VGS(th) –3.8 –2.7 –2.0 Vdc
Gate Quiescent Voltage (VDD = 48 Vdc, IDA = 250 mAdc, Measured in Functional Test) VGSA(Q) –3.2 –2.7 –2.2 Vdc
Gate--Source Leakage Current (VDS = 150 Vdc, VGS = –8 Vdc) IGSS –8.1 — — mAdc

On Characteristics — Side B, Peaking

Gate Threshold Voltage (VDS = 10 Vdc, ID = 42 mAdc) VGS(th) –3.8 –3.1 –2.0 Vdc
Gate--Source Leakage Current (VDS = 150 Vdc, VGS = –8 Vdc) IGSS –9.99 — — mAdc
  1. Refer to AN1955, Thermal Measurement Methodology of RF Power Amplifiers. Go to http://www.nxp.com/RF and search for AN1955. 2. RCHC (FEA) must be used for purposes related to reliability and limitations on maximum channel temperature. MTTF may be estimated by the expression MTTF (hours) = 10[A + B/(T + 273)], where T is the channel temperature in degrees Celsius, A = –11.1 and B = 8366. 3. Each side of device measured separately.

(continued)

Page 3

Table 5. Electrical Characteristics (TA = 25C unless otherwise noted) (continued)

Characteristic

Symbol

Min Typ Max Unit

Functional Tests (1) (In NXP Doherty Production Test Fixture, 50 ohm system) VDD = 48 Vdc, IDQA = 250 mA, VGSB = –5.5 Vdc, Pout = 59 W Avg., f = 2690 MHz, Single--Carrier W--CDMA, IQ Magnitude Clipping, Input Signal PAR = 9.9 dB @ 0.01% Probability on CCDF. ACPR measured in 3.84 MHz Channel Bandwidth @ 5 MHz Offset. [See note on correct biasing sequence.]

Power Gain Gps 12.0 13.3 15.0 dB
Drain Efficiency D 42.7 48.5 — %
Psat, Pulsed CW Psat 55.7 56.6 — dBm
Adjacent Channel Power Ratio ACPR — –34.5 –27.5 dBc

Wideband Ruggedness (In NXP Doherty Production Test Fixture, 50 ohm system) IDQA = 250 mA, VGSB = –5.5 Vdc, f = 2590 MHz, Additive White Gaussian Noise (AWGN) with 10 dB PAR ISBW of 400 MHz at 55 Vdc, 125 W Avg. Modulated Output Power

No Device Degradation

(3 dB Input Overdrive from 59 W Avg. Modulated Output Power)

Typical Performance (In NXP Doherty Production Test Fixture, 50 ohm system) VDD = 48 Vdc, IDQA = 250 mA, VGSB = –5.5 Vdc, 2496–2690 MHz Bandwidth

Pout @ 3 dB Compression Point (2) P3dB — 420 — W
AM/PM (Maximum value measured at the P3dB compression point across the 2496–2690 MHz bandwidth) — –9 —
VBW Resonance Point (IMD Third Order Intermodulation Inflection Point) VBWres — 220 — MHz
Gain Flatness in 194 MHz Bandwidth @ Pout = 59 W Avg. GF — 0.2 — dB
Gain Variation over Temperature (–40C to +85C) G — 0.013 — dB/C
Output Power Variation over Temperature (–40C to +85C) P1dB — 0.006 — dB/C

Table 6. Ordering Information

Device Tape and Reel Information Package
A3G26H350W17SR3 R3 Suffix = 250 Units, 44 mm Tape Width, 13--inch Reel NI--780S--4S2S
  1. Part internally input matched. 2. P3dB = Pavg + 7.0 dB where Pavg is the average output power measured using an unclipped W--CDMA single--carrier input signal where output PAR is compressed to 7.0 dB @ 0.01% probability on CCDF.

NOTE: Correct Biasing Sequence for GaN Depletion Mode Transistors in a Doherty Configuration

Bias ON the device 1. Set gate voltage VGSA and VGSB to –5 V. 2. Set drain voltage VDSA and VDSB to nominal supply voltage (+48 V). 3. Increase VGSA (carrier side) until IDQA current is attained. 4. Increase VGSB (peaking side) to target bias voltage. 5. Apply RF input power to desired level.

Bias OFF the device 1. Disable RF input power. 2. Adjust gate voltage VGSA and VGSB to –5 V. 3. Adjust drain voltage VDSA and VDSB to 0 V. Allow adequate time for drain voltage to reduce to 0 V from external drain capacitors. 4. Disable VGSA and VGSB.

Page 4

PDF page 4 diagram

aaa--038550

Figure 2. A3G26H350W17S Production Test Circuit Component Layout

Table 7. A3G26H350W17S Production Test Circuit Component Designations and Values

Part Description Part Number Manufacturer
C1, C9, C11, C12, C16, C18 10 F Chip Capacitor C5750X7S2A106M TDK
C2, C5, C7, C8, C13, C17 8.2 pF Chip Capacitor 600F8R2BT250XT ATC
C3 1 pF Chip Capacitor 600F1R0BT250XT ATC
C4 0.5 pF Chip Capacitor 600F0R5BT250XT ATC
C6 0.9 pF Chip Capacitor 600F0R9BT250XT ATC
C10, C19 220 F, 100 V Electrolytic Capacitor MCGPR100V227M16X26 Multicomp
C14 3.0 pF Chip Capacitor 600F3R0BT250XT ATC
C15 5.1 pF Chip Capacitor 600F5R1BT250XT ATC
C20 0.2 pF Chip Capacitor 600F0R2BT250XT ATC
R1, R7 15 k, 1/4 W Chip Resistor CRCW120615K0FKEA Vishay
R2, R6 3 , 1/4 W Chip Resistor CRCW12063R00JNEA Vishay
R3, R5 1 , 1/4 W Chip Resistor CRCW12061R00FKEA Vishay
R4 50 , 10 W Termination Chip Resistor C10A50Z4 Anaren
Z1 2300–2900 MHz Band, 90, 3 dB Hybrid Coupler X3C26P1-03 Anaren
PCB Rogers RO4350B, 0.020, r = 3.66 D131318 MTL

Page 5

PACKAGE INFORMATION

PDF page 5 diagram
PDF page 5 diagram
PDF page 5 diagram

Page 6

PDF page 6 diagram

Page 7

PRODUCT DOCUMENTATION, SOFTWARE AND TOOLS

Refer to the following resources to aid your design process. Application Notes  AN1908: Solder Reflow Attach Method for High Power RF Devices in Air Cavity Packages AN1955: Thermal Measurement Methodology of RF Power Amplifiers  Software .s2p File  Development Tools  Printed Circuit Boards

REVISION HISTORY

The following table summarizes revisions to this document.

Revision Date Description
0 Nov. 2020  Initial release of data sheet
1 Jan. 2021  Table 1, Maximum Ratings: updated operating voltage for complete data sheet standardization, p. 2  Table 2, Recommended Operating Conditions: added to data sheet, p. 2

Page 8

Information in this document is provided solely to enable system and software

How to Reach Us:

implementers to use NXP products. There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits based on the information

Home Page:

in this document. NXP reserves the right to make changes without further notice to any

nxp.com

products herein.

Web Support:

NXP makes no warranty, representation, or guarantee regarding the suitability of its

nxp.com/support

products for any particular purpose, nor does NXP assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters that may be provided in NXP data sheets and/or specifications can and do vary in different applications, and actual performance may vary over time. All operating parameters, including “typicals,” must be validated for each customer application by customer’s technical experts. NXP does not convey any license under its patent rights nor the rights of others. NXP sells products pursuant to standard terms and conditions of

sale, which can be found at the following address: nxp.com/SalesTermsandConditions.

NXP, the NXP logo and Airfast are trademarks of NXP B.V. All other product or service names are the property of their respective owners. E 2020–2021 NXP B.V.

PDF page 8 diagram