DATASHEET SEARCH SITE
Document overview
- PDF pages: 8
Technical content
Page 1
Technical Data
RF Power GaN Transistor
Document Number: A3G23H500W17S
Rev. 1, 05/2021

This 80 W asymmetrical Doherty RF power GaN transistor is designed for cellular base station applications requiring very wide instantaneous bandwidth capability covering the frequency range of 2300 to 2400 MHz. This part is characterized and performance is guaranteed for applications operating in the 2300 to 2400 MHz band. There is no guarantee of performance

when this part is used in applications designed outside of these frequencies.
2300 MHz Typical Doherty Single--Carrier W--CDMA Performance: VDD = 48 Vdc, IDQA = 300 mA, VGSB = –5.0 Vdc, Pout = 80 W Avg., Input Signal PAR = 9.9 dB @ 0.01% Probability on CCDF.

| Frequency | Gps (dB) | D (%) | Output PAR (dB) | ACPR (dBc) |
| 2300 MHz | 14.5 | 53.7 | 8.4 | –30.5 |
| 2350 MHz | 14.6 | 52.8 | 8.3 | –30.6 |
| 2400 MHz | 14.2 | 53.2 | 8.1 | –31.9 |
Features

High terminal impedances for optimal broadband performance Advanced high performance in--package Doherty Improved linearized error vector magnitude with next generation signal Able to withstand extremely high output VSWR and broadband operating conditions

Page 2
Table 1. Maximum Ratings
| Rating | Symbol | Value | Unit |
|---|---|---|---|
| Drain--Source Voltage | VDSS | 125 | Vdc |
| Gate--Source Voltage | VGS | –8, 0 | Vdc |
| Operating Voltage | VDD | 55 | Vdc |
| Maximum Forward Gate Current, IG (A+B), @ TC = 25C | IGMAX | 66 | mA |
| Storage Temperature Range | Tstg | –65 to +150 | C |
| Case Operating Temperature Range | TC | –55 to +150 | C |
| Maximum Channel Temperature | TCH | 225 | C |
Table 2. Recommended Operating Conditions
| Rating | Symbol | Value | Unit |
|---|---|---|---|
| Operating Voltage | VDD | 48 | Vdc |
Table 3. Thermal Characteristics
| Characteristic | Symbol | Value | Unit |
|---|---|---|---|
| Thermal Resistance by Infrared Measurement, Active Die Surface--to--Case Case Temperature 90C, PD = 84 W | R JC (IR) | 0.53 (1) | C/W |
| Thermal Resistance by Finite Element Analysis, Channel--to--Case Case Temperature 90C, PD = 84 W | R CHC (FEA) | 0.96 (2) | C/W |
Table 4. ESD Protection Characteristics
| Test Methodology | Class |
| Human Body Model (per JS--001--2017) | 1C |
| Charge Device Model (per JS--002--2014) | C3 |
Table 5. Electrical Characteristics (TA = 25C unless otherwise noted)
Symbol
Min Typ Max Unit
Characteristic
Off Characteristics (3) Drain--Source Breakdown Voltage
V(BR)DSS
— — Vdc
(VGS = –8 Vdc, ID = 24 mAdc)
Carrier
150
(VGS = –8 Vdc, ID = 42 mAdc)
150
Peaking
On Characteristics — Side A, Carrier
| Gate Threshold Voltage (VDS = 10 Vdc, ID = 20 mAdc) | VGS(th) | –3.5 | –2.8 | –2.3 | Vdc |
| Gate Quiescent Voltage (VDD = 48 Vdc, IDA = 300 mAdc, Measured in Functional Test) | VGSA(Q) | –3.2 | –2.7 | –2.2 | Vdc |
| Gate--Source Leakage Current (VDS = 150 Vdc, VGS = –8 Vdc) | IGSS | –9.9 | — | — | mAdc |
On Characteristics — Side B, Peaking
| Gate Threshold Voltage (VDS = 10 Vdc, ID = 20 mAdc) | VGS(th) | –3.8 | –3.1 | –2.3 | Vdc |
| Gate--Source Leakage Current (VDS = 150 Vdc, VGS = –8 Vdc) | IGSS | –9.9 | — | — | mAdc |
- Refer to AN1955, Thermal Measurement Methodology of RF Power Amplifiers. Go to http://www.nxp.com/RF and search for AN1955. 2. RCHC (FEA) must be used for purposes related to reliability and limitations on maximum channel temperature. MTTF may be estimated by the expression MTTF (hours) = 10[A + B/(T + 273)], where T is the channel temperature in degrees Celsius, A = –11.1 and B = 8366. 3. Each side of device measured separately.
(continued)
Page 3
Table 5. Electrical Characteristics (TA = 25C unless otherwise noted) (continued)
Characteristic
Symbol
Min Typ Max Unit
Functional Tests (1) (In NXP Doherty Production Test Fixture, 50 ohm system) VDD = 48 Vdc, IDQA = 300 mA, VGSB = –5.0 Vdc, Pout = 80 W Avg., f = 2300 MHz, Single--Carrier W--CDMA, IQ Magnitude Clipping, Input Signal PAR = 9.9 dB @ 0.01% Probability on CCDF. ACPR measured in 3.84 MHz Channel Bandwidth @ 5 MHz Offset. [See note on correct biasing sequence.]
| Power Gain | Gps | 13.3 | 14.3 | 16.5 | dB |
| Drain Efficiency | D | 48.0 | 52.7 | — | % |
| Psat, Pulsed CW | Psat | 55.7 | 56.4 | — | dBm |
| Adjacent Channel Power Ratio | ACPR | — | –34.2 | –31.3 | dBc |
Wideband Ruggedness (In NXP Doherty Production Test Fixture, 50 ohm system) IDQA = 300 mA, VGSB = –5.0 Vdc, f = 2350 MHz, Additive White Gaussian Noise (AWGN) with 10 dB PAR ISBW of 400 MHz at 55 Vdc, 151 W Avg. Modulated Output Power
No Device Degradation
(3 dB Input Overdrive from 80 W Avg. Modulated Output Power)
Typical Performance (In NXP Doherty Production Test Fixture, 50 ohm system) VDD = 48 Vdc, IDQA = 300 mA, VGSB = –5.0 Vdc, 2300–2400 MHz Bandwidth
| Pout @ 3 dB Compression Point (2) | P3dB | — | 603 | — | W |
| AM/PM (Maximum value measured at the P3dB compression point across the 2300–2400 MHz bandwidth) | | — | –8 | — | |
| VBW Resonance Point (IMD Third Order Intermodulation Inflection Point) | VBWres | — | 300 | — | MHz |
| Gain Flatness in 100 MHz Bandwidth @ Pout = 80 W Avg. | GF | — | 0.25 | — | dB |
| Gain Variation over Temperature (–40C to +85C) | G | — | 0.008 | — | dB/C |
| Output Power Variation over Temperature (–40C to +85C) | P3dB | — | 0.003 | — | dB/C |
Table 6. Ordering Information
| Device | Tape and Reel Information | Package |
| A3G23H500W17SR3 | R3 Suffix = 250 Units, 44 mm Tape Width, 13--inch Reel | NI--780S--4S2S |
- Part internally input matched. 2. P3dB = Pavg + 7.0 dB where Pavg is the average output power measured using an unclipped W--CDMA single--carrier input signal where output PAR is compressed to 7.0 dB @ 0.01% probability on CCDF.
NOTE: Correct Biasing Sequence for GaN Depletion Mode Transistors in a Doherty Configuration
Bias ON the device 1. Set gate voltage VGSA and VGSB to –5 V. 2. Set drain voltage VDSA and VDSB to nominal supply voltage (+48 V). 3. Increase VGSA (carrier side) until IDQA current is attained. 4. Increase VGSB (peaking side) to target bias voltage. 5. Apply RF input power to desired level.
Bias OFF the device 1. Disable RF input power. 2. Adjust gate voltage VGSA and VGSB to –5 V. 3. Adjust drain voltage VDSA and VDSB to 0 V. Allow adequate time for drain voltage to reduce to 0 V from external drain capacitors. 4. Disable VGSA and VGSB.
Page 4

Figure 2. A3G23H500W17S Production Test Circuit Component Layout
Table 7. A3G23H500W17S Production Test Circuit Component Designations and Values
| Part | Description | Part Number | Manufacturer |
|---|---|---|---|
| C1, C8, C9, C11, C15, C17 | 10 uF Chip Capacitor | C5750X7S2A106M | TDK |
| C2, C4, C5, C7, C10, C16 | 11 pF Chip Capacitor | 600F110JT250XT | ATC |
| C3 | 1.2 pF Chip Capacitor | 600F1R2BT250XT | ATC |
| C6 | 0.8 pF Chip Capacitor | 600F0R8BT250XT | ATC |
| C12 | 3.9 pF Chip Capacitor | 600F3R9BT250XT | ATC |
| C13 | 6.8 pF Chip Capacitor | 600F6R8BT250XT | ATC |
| C14 | 0.6 pF Chip Capacitor | 600F0R6BT250XT | ATC |
| C18, C19 | 220 F, 100 V Electrolytic Capacitor | MCGPR100V227M16X26-RH | Multicomp |
| C20 | 0.3 pF Chip Capacitor | 600F0R3BT250XT | ATC |
| R1 | 50 , 10 W Termination Chip Resistor | C10A50Z4 | Anaren |
| R2, R3 | 3.6 , 1/4 W Chip Resistor | CRCW12063R60FKEA | Vishay |
| Z1 | 2300–2700 MHz, 90, 4 dB Hybrid Coupler | X3C25P1-04S | Anaren |
| PCB | Rogers RO4350B, 0.020, r = 3.66 | D140827 | MTL |
Page 5
PACKAGE INFORMATION



Page 6

Page 7
PRODUCT DOCUMENTATION, SOFTWARE AND TOOLS
Refer to the following resources to aid your design process. Application Notes AN1908: Solder Reflow Attach Method for High Power RF Devices in Air Cavity Packages AN1955: Thermal Measurement Methodology of RF Power Amplifiers Software .s2p File Development Tools Printed Circuit Boards
REVISION HISTORY
The following table summarizes revisions to this document.
| Revision | Date | Description |
|---|---|---|
| 0 | Apr. 2021 | Initial release of data sheet |
| 1 | May 2021 | Table 3, ESD Protection Characteristics: added Human Body Model, p. 2 |
Page 8
Information in this document is provided solely to enable system and software
How to Reach Us:
implementers to use NXP products. There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits based on the information
Home Page:
in this document. NXP reserves the right to make changes without further notice to any
nxp.com
products herein.
Web Support:
NXP makes no warranty, representation, or guarantee regarding the suitability of its
nxp.com/support
products for any particular purpose, nor does NXP assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters that may be provided in NXP data sheets and/or specifications can and do vary in different applications, and actual performance may vary over time. All operating parameters, including “typicals,” must be validated for each customer application by customer’s technical experts. NXP does not convey any license under its patent rights nor the rights of others. NXP sells products pursuant to standard terms and conditions of
sale, which can be found at the following address: nxp.com/SalesTermsandConditions.
NXP, the NXP logo and Airfast are trademarks of NXP B.V. All other product or service names are the property of their respective owners. E 2021 NXP B.V.
