6009W4PAM61B30X CONEC

Document overview

  • Manufacturer or author: Provided By www.digicamel.com(free datasheet download site)
  • PDF pages: 2

Technical content

( 5 : 1 ) AA AA AA AA BB BB BB BB CC CC CC CC DD DD DD DD EE EE EE EE FF FF FF FF AA AA AA AA BB BB BB BB CC CC CC CC DD DD DD DD 6009W4PAM61B30X CONEC ABC dim. in mm RR RR date drawn THIS DRAW ING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH d-old norm appd. tolerance material: title: dwg no: DIN- sh: part no: namedate namedescriptionrev.DO NOT ALTER CAD DRAWING BY HAND scale: 15K1A1591 D-SUB COMBINATION MALE see notes Henneboel12.12.14

12.12.14 Lehmenkühler

with threaded insert and hexlocking screw 2:1 (5:1) 6009W4PAM61B30X a Original 38,86 - 0,02 0,23+ Pos. 1 Pos. 3 Pos. A1 SEE NOTE 15 1,12n (5x) 5,7 -0,31 7,1 0,314,23 -0,38 0,12 8,26 - 0,03 0,22+ SEALING COMPOUND RUBBER GASKET PLACED ON TOP SURFACE OF MALE INSULATOR 1,8n (4x) 10° O-RING SEE NOTE 8 4,8SW 4-40 UNC AT ALL TIMES WATER RESISTANT CONNECTORS NOT IN USE SHOULD BE COVERED WITH A CONEC WATER RESISTANT CAP OR WATER TIGHT HOOD. 3,6 -00,25 NOTES: 1. RECOMMENDED SOLDER INSTRUCTION SEE SHEET 2 2. METALSHELLS: COPPER ALLOY; min. 315µin TIN ove r 40-80µin NICKEL 3. INSULATORS: PBT GF UL 94 V-0; GREEN 4. SIGNAL CONTACTS: COPPER ALLOY PLATING: GOLD FLASH over NICKEL SOLDER CUP ACCEPTS CABLE AWG 20 5. HIGH POWER CONTACTS 10A: COPPER ALLOY PLATING, MATING AREA: GOLD FLASH over NICKEL PLATING, TERMINATION SIDE: GOLD FLASH over NI CKEL SOLDER CUP ACCEPTS CABLE AWG 16-20 6. THREADED INSERTS: COPPER ALLOY; min. 200µin TI N over 80µin NICKEL 7. COLLARS: COPPER ALLOY, min. 200µin TIN over 80 µin NICKEL 8. FRAME: ZINC DIE CAST; NICKEL PLATED 9. O-RING: SILICON; BLUE 10. RUBBER GASKET: TPE; BLACK 11. HEXLOCKING SCREWS: STAINLESS STEEL 12. SEALING COMPOUND: PUR; BLUE 13. RECOMMENDED PANEL CUT-OUT ON SHEET 2 14. RECOMMENDED TORQUE FOR MOUNTING SCREW 35Ncm (3,1 in.LB) / max. 40Ncm (3,5 in.LB) 15. CONNECTOR IS PART MARKED: 6009W4PAM61B30X CON EC ABC 47,04\` 0,13 61,4 - 0 0,3+ 21,1 -00,3 4-40 UNC RoHS compliant

dim. in mm RR RR date drawn THIS DRAW ING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH d-old norm appd. tolerance material: title: dwg no: DIN- sh: part no: namedate namedescriptionrev.DO NOT ALTER CAD DRAWING BY HAND scale: 15K1A1591 PANEL CUT-OUT see sheet 1 Henneboel12.12.14 D-SUB COMBINATION MALE 9W4P with threaded insert and hexlocking screw 3:1 SEE SHEET 1 a Original 42,5\ 0,1 3,1 0,05 n (2x) 3,4 R \ 0,13 11,4 0,1 i 0,26 A 10°\ 1° 47,04\ 0,1 B i 0,26 B A RECOMMENDED PANEL CUT-OUT Solder Instruction 1. Cable should be prepared for soldering. The cable/wires must be pretinned. 2. Insert cable/wire into solder cup. 3. Signal Contact 3.1. Operate the soldering iron at 350° C, 50 Watt max. and use a pencil tip. 3.2. Put tip to wire in solder cup. 3.3. After 1 second bring in solder. 3.4. Heat for 3 seconds longer. Do not heat contact more than 4 seconds in total. 4. Power Contact 4.1. Operate the soldering iron at 350° C, 100 Watt max. and use a pencil tip. 4.2. Apply some solder to the solder tip of the soldering iron. 4.3. Put tip to wire in solder cup. 4.4. After 1 second bring in solder. 4.5. Heat for 5 seconds longer. Do not heat contact more than 6 seconds in total. 5. Remove soldering iron. 6. Wait until solder gets rigid again. 7. Do not solder adjacent contacts consecutively, alternate position within the connector to minimize heat build up.