5KP DBLECTRO
Document overview
- Manufacturer or author: Provided By digicamel.com
- PDF pages: 3
Technical content
For bidirectional type having Vrwm of 10 volts and less, the IR limit is double. For parts without A , the VBR is + 10% VOLTAGE - 5.0 TO 180 Volts 5000Watts Peak Pulse Power 5KP SERIES GLASS PASSIVATED JUNCTION TRANSIENT VOLTAGE SUPPRESSOR 5KP PART NUMBER REVERSE STAND- OFF VOLTAGE VRWM(V) BREAKDOWN VOLTAGE VBR(V) MIN. @IT BREAKDOWN VOLTAGE VBR(V) MAX. @IT TEST CURRENT IT (mA) MAXIMUM CLAMPING VOLTAGE @Ipp Vc(V) PEAK PULSE CURRENT Ipp (A) REVERSE LEAKAGE @ VRWM IR(µA)
FEATURES
Glass passivated chip junction Excellent clamping capability Pepetition rate(duty cycle):0.05% Low incremental surge resistance Fast response time: typically less than 1.0ps from 0 Volts to BV Typical IR less than 3mA for Vbr>=10V High temperature soldering guaranteed: 265°C/10 seconds/.375", (9.5mm) lead length, 5lbs., (2.3kg) tension MECHANICAL DATA Case: Molded plastic over glass passivated junction Mounting Position: Any Weight: 0.07ounce, 2.1gram SYMBOL VALUE UNITS P PPM Minimum
5000 Watts
PM(AV) 8 Watts TJ , TSTG -55 to + 175 Notes : 1.Non-repetitive current pulse , per Fig. 3 and derated above TA = 25 per Fig. 2 . 3.8.3ms single half sine-wave , or equivalent square wave, Duty cycle = 4 pulses per minutes maximum. 5KP SERIES GLASS PASSIVATED JUNCTION TRANSIENT VOLTAGE SUPPRESSOR VOLTAGE-5.0 TO 180 Volts 5000 watt Peak Pulse Power DEVICES FOR BIPOLAR APPLICATION For Bidirectional use C or CA Suffix for types 5KP5.0 thru types 5KP180 (e.g. 5KP5.0C , 5KP180CA) Electrical characteristics apply in both directions MAXIMUM RATINGS AND CHARACTERISTICS Peak Pulse Power Dissipation on 10/1000 s waveform (Note 1,FIG.1) Peak Pulse Current of on 10/1000 s waveform (Note 1,FIG.3) Peak Forward Surge Current,8.3ms Single Half Sine-Wave Superimposed on Rated Load,(JEDEC Method) (Note 3) 5000W Peak Pulse Power capability on 10/1000µs waveform Terminal: Plated Axial leads, solderable per MIL-STD-750, Method 2026 Polarity: Color band denotes positive end (cathode) except Bipolar Operating junction and Storage Temperature Range Ratings at 25 ambient temperature unless otherwise specified. Steady State Power Dissipation at TL = 75 , Lead lengths.375",(9.5mm) (Note 2) IFSM 400 Amps RATING
Characteristic Curves(TA=25 unless otherwise noted) 5KP SERIES RATINGS AND CHARACTERISTIC CURVES PPM(AV),Steady State Power Dissipation (W) 0 25 50 75 100 125 150 175 200 Fig. 5 - Steady State Power Derating Curve TL - Lead Temperature (°C) 0.375" (9.5mm) Lead Lengths Copper Heat Sinks 60Hz Resistive or Inductive Load 12.5 37.5 62.5 87.5 100 0 25 50 75 100 125 150 175 200 Fig.2 - Pulse Derating Curve TA - Ambient Temperatur(°C) PPPM-Peak Pulse Power (kW) 3.0 4.0 150 1.0 2.0 tr = 10µsec. Peak Value I PPM TJ = 25°C Pulse Width(td)is defined as the point where the peak current decays to 50% of I PPM 10/1000µsec.Waveform as defined by R.E.A. td Fig.3 - Pulse Waveform 4.0 Half Value- IPPM 100 IPPM - Peak Pulse Current,% IRSM 3.00 t - Time(ms) 200 250 300 350 400 450 500 1 10 100 Fig.6 - Maximum Non-repetitive Forward Surge current Number of Cycles at 60 HZ IFSM,Peak Forward Surge Currnet (A) 8.3ms Single Half Sine-Wave (JEDEC Method) 0.1 100 10ms0.1µs 1.0µs 10µs 100µs 1.0ms td - Pulse Width (sec.) Fig. 1 - Peak Pulse Power Rating Curve PPPM-Peak Pulse Power (kW) Non-repetitive pulse waveform shown in Fig.3 T A = 25°C 100 1000 10000 100000 1 10 100 100 5 Fig. 4 - Typical Junction Capacitance 10 200 Measured at Stand-off Vottage, V WM Measured at Zero Bias TJ = 25°C f = 1MHZ Vsig = 50mVp-p t,Time (ms) CJ, Junction Capacitance (pF)